AMSAT-NA/PacSatSW

Issues

• Config.h variables should be fully documented

  #40 opened 4 months ago
  0

• An Ax5043 is partially working on a Launchpad board

  #39 opened 5 months ago
  1

• Code to turn PA power on and off with Tx

  #38 opened 6 months ago
  0

• We should try the RTC multiple times at startup before assuming it is not working

  #37 opened 7 months ago
  6

• Add the callsigns to the start up messages in the console

  #36 opened 9 months ago
  0

• The receiver should be configurable by command to process PB, BBS, Commands or Digi

  #35 opened 9 months ago
  0

• A ground command should allow the packet rate to be set for each channel

  #34 opened 9 months ago
  0

• Digipeater needs to be implemented

  #33 opened 9 months ago
  0

• Don't add corrupt headers to the dir

  #32 opened 9 months ago
  0

• Updating or purging a file should always send a valid dir header to the ground station.

  #31 opened 9 months ago
  0

• PB File broadcast does not handle the TX Queue being fulll

  #30 opened 9 months ago
  0

• The ax5043 power levels are hard coded.

  #29 opened 9 months ago
  1

• If we update the oldest header then the client can not close the hole in the dir

  #28 opened 9 months ago
  1

• Add bytes to digipeted packets to show signal strength or congestion

  #27 opened 10 months ago
  2

• Time on spacecraft is offset by 6 hours when booted and connected to debugger

  #26 opened 9 months ago
  0

• Time message error

  #25 opened 9 months ago
  4

• Directory is corrupted if the uploader has a 6 digit callsign

  #24 opened 9 months ago
  2

• The logic for setting the clock needs to be decided. Right now only set at boot.

  #23 opened a year ago
  0

• Telemetry conversions for the demo

  #22 opened a year ago
  2

• The ground station pauses after uploading a file even if it has another to upload

  #21 opened a year ago
  0

• dir_next_file_number() should confirm there is no file on disk with the same number already

  #20 opened 9 months ago
  2

• In process file uploads need to be stored in a table in MRAM.

  #19 opened 9 months ago
  3

• FalconSat-3 sent a UI frame each time a station logged in. We do not.

  #18 opened a year ago
  0

• The number of AX25 preamble bytes should vary based on baud rate and back to back packets

  #17 opened a year ago
  3

• The AX5043 interrupt needs to pass the RX Channel number to the RxTask()

  #16 opened 9 months ago
  4

• We should support longer packets that span more than one AX5043 FIFO.

  #15 opened a year ago
  0

• PB, Uplink and DIR maintenance functions need to run periodically

  #14 opened a year ago
  2

• We need to keep track of the number of bytes broadcast and send the value in a BSTAT packet

  #13 opened a year ago
  0

• We do not check the version bits for incoming PB Packets

  #12 opened a year ago
  0

• Copy of a PB Entry could be optimized better

  #11 opened a year ago
  0

• Commandable configuration is currently set with #defines

  #10 opened a year ago
  0

• Code needs to be written to support the Real Time Clock (RTC)

  #9 opened a year ago
  1

• The state of the radios should be stored in a structure so it can be included in telemetry

  #8 opened a year ago
  1

• Flow ON and OFF are currently not used in the AX25 state machine

  #7 opened a year ago
  1

• Send a DM message to a station that tries to connect to an already busy channel

  #6 opened a year ago
  0

• Many functions return an error code but the error is not yet logged or handled

  #5 opened a year ago
  1

• If the processor resets then connected stations or PB sessions will be lost

  #4 opened a year ago
  4

• If Unix time is not set then the DIR does not load correctly at startup

  #2 opened 2 years ago
  1

• PB only handles the first hole in a list of dir holes.

  #1 opened 2 years ago
  1