This Arduino LoRa library is I hope different to other libraries, this LoRa library has a specific emphasis on providing a large range of working examples for common applications.
There are the normal basic transmit and receive examples, but there are many additional real world examples for;
- Sending and receiving sensor data.
- Remote control of devices, turning LEDs on\off etc.
- GPS tracker transmitters and receivers with displays.
- Using joysticks and servos for remote control.
- Examples using sleep modes for low power consumption.
- High altitude balloon trackers.
- Transferring large data arrays or files.
- Sending and receiving images from ESP32CAMs.
- Sending and receiving packets where an acknowledge is required.
- Sending polling requests to remote nodes for the return of specific data.
- Link test programs to test LoRa devices and antennas.
- Packet loggers with displays.
- Transmitting data with FSK RTTY.
- Transmitting FM tones and playing tunes (Star Wars).
The coding style of the library functions is (I hope) kept simple so that its easy to understand and modify for custom applications.
There are the standard examples showing how to send and receive arrays of data and very easy to use examples that write and read data and variables direct into and from the LoRa devices internal buffer. Examples for sending and receiving structures too.
The library includes the concept of 'Reliable' packets where the library functions automatically append a payload CRC and network ID to each packet. This means the receiver can be very confident that the received packet is from a known source and in the correct sequence. Additionally the transmitter can require a valid acknowledge response from the receiver before it continues. A transmitter can send 'Reliable' poll messages so that only a specific node will respond.
The reliable packets are used for the data transfer examples where LoRa can be used to reliably move images, files or arrays from one Arduino to another. These image or file transfers can also be forwarded from the Arduino to a folder on a PC via a local Serial YModem transfer.
There are examples for the distance measuring or ranging functions of the SX128X, tested up to 85km. Fast Long Range Communication (FLRC) packets are also supported on the SX128X and these packets have an on air rate of up to 1,300,000bps.
The Semtech LoRa devices are used to manufacture a range of LoRa modules sold by companies such as Hope, Dorji, NiceRF and others. The library does not support LoRa modules with a UART based interface such as those from Ebyte and Microchip.
The library does support the following Semtech LoRa devices;
SX1262,SX1262,SX1268,SX1272,SX1276,SX1277,SX1278,SX1279,SX1280,SX1281
However, its up to module manufactures to connect the Semtech LoRa devices up as they see fit. There are several options and additional control pins that a module manufacturer can add, so just because a module uses for example an SX1262 it does not mean the library code can support that particular modules combination of pins. See the section 'Considerations for pin usage' below.
A prime objective of the library was to allow the same program sketches to be used across the range of UHF LoRa modules (SX126x and SX127x) as well as the 2.4Ghz SX128x modules. With this library a sketch written for the SX1278 should run with very minor changes on the SX1262 or SX1280. However, whilst the SX126x and SX128x modules use the same style of internal device programming, the SX127x internal programming is completely different. The function style used for the SX126x and SX128x devices has been emulated for the SX127x.
The base Semtech devices that this library supports are all 3.3V logic level devices and most available modules do not include logic level conversion circuits. So do not use modules directly with 5V logic level Arduinos unless some form of logic level conversion is implemented. There are no specific logic level converters I could recommend.
To install the library select the 'Clone or download' button on the main Git hub page, then select 'Download Zip'. In the Arduino IDE select 'Sketch' then 'Include Library'. Next select 'Add .ZIP library' and browse to and select the ZIP file you downloaded, it's called 'SX12xx-master.zip'.
This library should work on versions 1.8.xx of the Arduino IDE. It has not been tested on versions 2.x.x of the Arduino IDE
A conventional LoRa library normally uses a buffer of data created within the Arduino sketch to contain the data that is sent as a packet. This library has those basic functions, see the example programs 3 and 4 in the 'Basics' folder. There are examples for sending\receiving a simple character buffer ("Hello World") and for sending\receiving a data structure which can also include a character buffer.
An additional feature has been implemented for this library to enable variables or character data to be written direct to the LoRa devices internal buffer. This has the benefit of not requiring a memory buffer in the Arduino and also lends itself to a simple easy to understand way of sending and receiving packets. For instance this is the routine to create a packet for transmission taken from the /LowMemory examples folder;
LT.startWriteSXBuffer(0); //start the write at location 0
LT.writeBuffer(trackerID, sizeof(trackerID)); //= 13 bytes (12 characters plus null (0) at end)
LT.writeUint32(TXpacketCount); //+4 = 17 bytes
LT.writeFloat(latitude); //+4 = 21 bytes
LT.writeFloat(longitude); //+4 = 25 bytes
LT.writeUint16(altitude); //+2 = 27 bytes
LT.writeUint8(satellites); //+1 = 28 bytes
LT.writeUint16(voltage); //+2 = 30 bytes
LT.writeInt8(temperature); //+1 = 31 bytes total to send
len = LT.endWriteSXBuffer();
This is the matching code for the receiver;
LT.startReadSXBuffer(0); //start buffer read at location 0
LT.readBuffer(receivebuffer); //read in the character buffer
txcount = LT.readUint32(); //read in the TXCount
latitude = LT.readFloat(); //read in the latitude
longitude = LT.readFloat(); //read in the longitude
altitude = LT.readUint16(); //read in the altitude
satellites = LT.readUint8(); //read in the number of satellites
voltage = LT.readUint16(); //read in the voltage
temperature = LT.readInt8(); //read in the temperature
RXPacketL = LT.endReadSXBuffer();
Clearly as with other methods of sending data the order in which the packet data is created in the transmitter has to match the order that it is read in the receiver.
Pins settings and usage must be set up either at the head of a program or in the the the 'Settings.h' file that is include in some sketch folders. Program 2_Register_Test is an example of a sketch that does not use a 'Settings.h' file. The library supports the SPI based LoRa modules and these all require that the SPI bus pins, SCK, MOSI and MISO are connected. All modules also need a NSS (chip select pin) and NRESET (reset) pin. All SX126X and SX128X devices need the RFBUSY pin to be used also.
Of the LoRa devices DIO pins the library in standard form only uses DIO0 (SX127X) and DIO1 (SX126X and SX128X). The pin definitions for DIO1 and DIO2 (SX127x) and DIO2 and DIO3 (SX126x and SX128x) are not currently used by the library or examples so can be defined as -1 meaning they will not be configured.
There are 'IRQ' library functions that do not need the use of the DIO0 (SX127X) or DIO1 (SX126X and SX128X) pins. These functions read the LoRa devices IRQ registers to check for transmit or receive completion. See examples such as 3_LoRa_TransmitterIRQ. On the SX127x devices you can normally leave the NRESET pin floating, the device clears itself at power on. This can save another IO pin. There are begin() methods for these combinations.
The Dorji DRF1262 and DRF1268 modules have an SW pin which must be connected, it provides power to the antenna switch used on these modules.
Some SX126x modules may have RX or TX enable pins, Ebyte E22 modules for instance. Whilst there is code in the SX126X library that was copied across from the SX128X library there were no SX126X devices using RX and TX switching available at the time this library was published, so these functions are currently not supported by the library as they have not been tested. If a user has SX126X modules that they want tested with the library, then donations of modules will be accepted.
Some of the SX128x modules may also have RX or TX enable pins, such as the Ebyte E28 modules. These functions have been tested and are supported for SX128x devices. You need to define the pins RX_EN and TX_EN pins used, otherwise leave unused by defining them as -1.
For testing the library and the example programs I used a board of my own design, which uses a 3.3V/8Mhz Arduino Pro Mini and has a socket where you can plug in a LoRa device as a Mikrobus style module. The board is small enough to be used for a GPS tracker application using the end connections for a GPS and display. See the Easy Pro Mini folder for details.
A good first example program to test a layout and connections would be the example program in the Basics folder 2_Register_Test, this just does a simple register print of the LoRa device. If this program does not work, then the rest of the example programs wont either. This program is self contained, it does not need the library installed to operate.
With an example program written and tested on this SX127x library the example should work with some minor changes with the SX126x and SX128x devices. Many of the example programs have already been tested and are working on SX126x, conversion typically takes less than a minute.
The Settings.h file in some examples contains the settings for the LoRa device such as frequency, spreading factor, bandwidth and coding rate. The example programs use a frequency of 434.000Mhz or 2.445Ghz for the SX128x, you will need to check if that frequency is permitted in your part of the World. The radio frequency spectrum is not a free for all, which frequencies, transmitter powers and duty cycles you are permitted to use varies by region and country. By default CRC checking is added to transmitted packets and used to check for errors on reception.
Some of the example sketches, in particular the camera and file transfer sketches use additional Arduino libraries. Some of these such as the SD libraries are part of the Arduino IDE, others you have to download and install. Most of these additional libraries are reliable, but some, such as the SD libraries may not be with some combinations of hardware.
All of the library functions are public and can be accessed from users sketches.
The basic functions will be described in the order that example program 3_LoRa_Transmitter uses them.
SPI.begin()
Standard Arduino library function. Sets up SPI. The library then internally uses;
SPI.beginTransaction(SPISettings(LTspeedMaximum, LTdataOrder, LTdataMode))
before every use of the SPI and this function after it;
SPI.endTransaction()
The parameters used are LTspeedMaximum, LTdataOrder and LTdataMode are defined in SX12XXLT_Definitions.h as;
LTspeedMaximum 8000000
LTdataOrder MSBFIRST
LTdataMode SPI_MODE0
The use of SPI.beginTransaction and SPI.endTransaction can be disabled by commenting out this define at the top of the relevant SX12XXLT.cpp file;
#define USE_SPI_TRANSACTION
begin(NSS, NRESET, DIO0, LORA_DEVICE) (SX127X library)
begin(NSS, NRESET, RFBUSY, DIO1, LORA_DEVICE) (SX126X library)
begin(NSS, NRESET, RFBUSY, DIO1, LORA_DEVICE) (SX128X library)
The basic begin functions initialises the minimal hardware pins used by the device. The begin functions are slightly different for the SX127X, SX126X and SX128X libraries due to the different pins used. NSS, NRESET and DIO0 (SX127X) or DIO1 (SX126x and SX128X) are required.
Other LoRa device pins can be used if you choose and the full list of begin functions is;
SX126X
bool begin(int8_t pinNSS, int8_t pinNRESET, int8_t pinRFBUSY, int8_t pinDIO1, int8_t pinDIO2, int8_t pinDIO3, int8_t pinRXEN, int8_t pinTXEN, int8_t pinSW, uint8_t device);
bool begin(int8_t pinNSS, int8_t pinNRESET, int8_t pinRFBUSY, int8_t pinDIO1, uint8_t device);
bool begin(int8_t pinNSS, int8_t pinNRESET, int8_t pinRFBUSY, int8_t pinDIO1, int8_t pinSW, uint8_t device);
bool begin(int8_t pinNSS, int8_t pinNRESET, int8_t pinRFBUSY, int8_t pinDIO1, int8_t pinRXEN, int8_t pinTXEN, uint8_t device);
bool begin(int8_t pinNSS, int8_t pinNRESET, int8_t pinRFBUSY, uint8_t device);
SX127X
bool begin(int8_t pinNSS, int8_t pinNRESET, int8_t pinDIO0, int8_t pinDIO1, int8_t pinDIO2, uint8_t device);
bool begin(int8_t pinNSS, int8_t pinNRESET, int8_t pinDIO0, uint8_t device);
bool begin(int8_t pinNSS, int8_t pinNRESET, uint8_t device);
bool begin(int8_t pinNSS, uint8_t device);
SX128X
bool begin(int8_t pinNSS, int8_t pinNRESET, int8_t pinRFBUSY, int8_t pinDIO1, int8_t pinDIO2, int8_t pinDIO3, int8_t pinRXEN, int8_t pinTXEN, uint8_t device);
bool begin(int8_t pinNSS, int8_t pinNRESET, int8_t pinRFBUSY, int8_t pinDIO1, uint8_t device);
bool begin(int8_t pinNSS, int8_t pinNRESET, int8_t pinRFBUSY, int8_t pinDIO1, int8_t pinRXEN, int8_t pinTXEN, uint8_t device);
bool begin(int8_t pinNSS, int8_t pinNRESET, int8_t pinRFBUSY, uint8_t device);
bool begin(int8_t pinNSS, int8_t pinRFBUSY, uint8_t device);
Some DIOs are optional and when not used define as -1. The SX126X and SX128X devices have an RFBUSY pin. To ensure compatibility with Dorji SX1262 and SX1268 devices the SW pin needs to be defined. This pin turns on\off the antenna switch on Dorji devices. Set to -1 if not used. Some of the SX128X devices for example from eByte require TX and RX enable pins, set to -1 if your not using them.
LoRA_DEVICE tells the library which actual LoRa RF IC is being used and in the case of the SX127x devices how the antenna is connected. The choices are for the SX127x part of the library are;
DEVICE_SX1272
DEVICE_SX1276
DEVICE_SX1277
DEVICE_SX1278
DEVICE_SX1279
DEVICE_SX1272_PABOOST
DEVICE_SX1277_PABOOST
DEVICE_SX1278_PABOOST
DEVICE_SX1279_PABOOST
DEVICE_SX1276_RFO
DEVICE_SX1277_RFO
DEVICE_SX1278_RFO
DEVICE_SX1279_RFO
Note that in the above list for the SX127x part of the library only and there are new device types that allow the library to differentiate between devices that have the transmit output connected to the PA_BOOST pin (which is the vast majority of SX127x devices) and those that use the RFO LF_ANT or RFO HF_ANT pins for RF output. These RFO connected devices are in the minority and are limited to 14dBm output. There is no library support for a SX1272 using the RFO outputs as I don't have one to test.
The old device types; DEVICE_SX1272, DEVICE_SX1276, DEVICE_SX1277, DEVICE_SX1278 and DEVICE_SX1272 are retained for compatibility with old sketches and are the same device as those with the _PABOOST identity.
Devices using the PABOOST output can be set to power levels from 2dBm to 20dBm, and operation at 20dBm is limited to a 1% duty cycle. Devices using the RFO outputs can be set to power levels from 0dBm to 14dBm.
The device types for the SX126X and SX128X part of the library are;
DEVICE_SX1261 //SX126X library
DEVICE_SX1262 //SX126X library
DEVICE_SX1268 //SX126X library
DEVICE_SX1280 //SX128X library
DEVICE_SX1281 //SX128X library
The next library function called is normally;
setupLoRa(Frequency, Offset, SpreadingFactor, Bandwidth, CodeRate)
This function does the detailed set-up of the LoRa device by calling a number of separate library functions, the functions called are listed bellow. For a an example sketch of using the functions individually, see example 103_Lora_Transmitter_Detailed_Setup.
The functions within setupLoRa() are;
setMode(MODE_STDBY_RC)
Sets the operation mode of the LoRa device. Choices are;
MODE_SLEEP
MODE_STDBY
MODE_STDBY_RC
setPacketType(PACKET_TYPE_LORA)
Set the type of packet to use, currently only LORA is supported, choices are;
PACKET_TYPE_LORA
PACKET_TYPE_GFSK (not yet implemented)
PACKET_TYPE_FLRC (SX128X library only)
PACKET_TYPE_RANGING (SX128X library only)
PACKET_TYPE_BLE (SX128X library only) (not yet implemented)
PACKET_TYPE_NONE
setRfFrequency(Frequency, Offset)
Sets the operating frequency in hertz. A calibration offset also in hertz can be used if there is a calibration value known for a particular module.
calibrateImage(0)
Carries out an internal device calibration, normally carried out after setting the initial operating frequency.
setModulationParams(SpreadingFactor, Bandwidth, CodeRate, LDRO_AUTO)
Sets the LoRa modem parameters for Spreading factor, Bandwidth, CodeRate and Optimisation. The options are;
//LoRa Spreading factors
LORA_SF5 (SX126X and SX128X libraries only)
LORA_SF6
LORA_SF7
LORA_SF8
LORA_SF9
LORA_SF10
LORA_SF11
LORA_SF12
//LoRa Bandwidths SX127X and SX126X libraries
LORA_BW_500 //actual 500000hz
LORA_BW_250 //actual 250000hz
LORA_BW_125 //actual 125000hz
LORA_BW_062 //actual 62500hz
LORA_BW_041 //actual 41670hz
LORA_BW_031 //actual 31250hz
LORA_BW_020 //actual 20830hz
LORA_BW_015 //actual 15630hz
LORA_BW_010 //actual 10420hz
LORA_BW_007 //actual 7810hz
//LoRa Bandwidths SX128X library
LORA_BW_0200 //actually 203125hz
LORA_BW_0400 //actually 406250hz
LORA_BW_0800 //actually 812500hz
LORA_BW_1600 //actually 1625000hz
//LoRa Coding rates
LORA_CR_4_5
LORA_CR_4_6
LORA_CR_4_7
LORA_CR_4_8
The SX126X and SX127X devices have an low data rate optimisation setting that needs to be set when the symbol time is greater than 16mS. You can manually turn it on or off or set it to LDRO_AUTO and the library does the calculation for you.
//Low date rate optimisation, need to be set when symbol time > 16mS
LDRO_OFF
LDRO_ON
LDRO_AUTO //automatically calculated and set
setBufferBaseAddress(0x00, 0x00)
This sets the default address for the locations in the LoRa device buffer where transmitted and received packets start. The defaults of these locations are set in the transmit and receive functions, so this function is not normally required.
setPacketParams(PreAmblelength, LORA_PACKET_VARIABLE_LENGTH, PacketLength, LORA_CRC_ON, LORA_IQ_NORMAL)
Set the packet parameters. PreAmblelength is normally 8. There is a choice of LORA_PACKET_VARIABLE_LENGTH for variable length explicit packets or LORA_PACKET_FIXED_LENGTH for implicit packets. PacketLength is 1 to 255, it can be set here but is normally handled within the transmitter and receiver functions. There is the option of using a packet CRC with LORA_CRC_ON or not using a CRC with LORA_CRC_OFF. IQ can be set to LORA_IQ_NORMAL or LORA_IQ_INVERTED.
setSyncWord(LORA_MAC_PRIVATE_SYNCWORD)
You can define the syncword here, either a 8 bit value of your own choice or the standard values of LORA_MAC_PRIVATE_SYNCWORD (0x12) or LORA_MAC_PUBLIC_SYNCWORD (0x34). Take great care with setting your own syncwords, some values will not work and may not be compatible with other LoRa devices or can give reduced sensitivity. Best to stick to the standard PUBLIC and PRIVATE ones. There is no configurable syncword for SX128x devices.
setHighSensitivity()
Sets LoRa device for the highest sensitivity at expense of slightly higher LNA current. The alternative is setLowPowerReceive() for lower sensitivity with slightly reduced current.
setDioIrqParams(MASK, DIO0_MASK, DIO1_MASK, DIO2_MASK) (SX127X library)
setDioIrqParams(MASK, DIO0_MASK, DIO1_MASK, DIO2_MASK) (SX126X and SX128X libraries)
Sets up the how the device responds to internal events. This function is written for the SX127X to match the style used by the SX126X and SX128X devices. MASK is applied to the IRQ settings for DIO0, DIO1 and DIO2 (SX127X) and DIO1, DIO2 and DIO3 (SX126X and SX128X), its normally set to IRQ_RADIO_ALL (0xFFFF). Whilst the SX127X only has an 8 bit IRQ register the library has extended the function to provide additional IRQ detections that are used for the SX126X and SX127X.
In the case of the SX127X, the function maps the internal interrupts to the DIO0, DIO1 and DIO2 pins according to this table;
IRQ_RADIO_NONE 0x00
IRQ_CAD_ACTIVITY_DETECTED 0x01 //active on DIO1
IRQ_FSHS_CHANGE_CHANNEL 0x02 //active on DIO2
IRQ_CAD_DONE 0x04 //active on DIO0
IRQ_TX_DONE 0x08 //active on DIO0
IRQ_HEADER_VALID 0x10 //read from IRQ register only
IRQ_CRC_ERROR 0x20 //read from IRQ register only
IRQ_RX_DONE 0x40 //active on DIO0
IRQ_RADIO_ALL 0xFFFF
IRQ_TX_TIMEOUT 0x0100 //so that readIrqstatus can return additional detections
IRQ_RX_TIMEOUT 0x0200 //so that readIrqstatus can return additional detections
IRQ_NO_PACKET_CRC 0x0400 //so that readIrqstatus can return additional detections
The SX126X library has this table;
IRQ_RADIO_NONE 0x0000
IRQ_TX_DONE 0x0001
IRQ_RX_DONE 0x0002
IRQ_PREAMBLE_DETECTED 0x0004
IRQ_SYNCWORD_VALID 0x0008
IRQ_HEADER_VALID 0x0010
IRQ_HEADER_ERROR 0x0020
IRQ_CRC_ERROR 0x0040
IRQ_CAD_DONE 0x0080
IRQ_CAD_ACTIVITY_DETECTED 0x0100
IRQ_RX_TX_TIMEOUT 0x0200
IRQ_TX_TIMEOUT 0x0200
IRQ_RX_TIMEOUT 0x0200
IRQ_RADIO_ALL 0xFFFF
And the SX128X has this one;
IRQ_RADIO_NONE 0x0000
IRQ_TX_DONE 0x0001
IRQ_RX_DONE 0x0002
IRQ_SYNCWORD_VALID 0x0004
IRQ_SYNCWORD_ERROR 0x0008
IRQ_HEADER_VALID 0x0010
IRQ_HEADER_ERROR 0x0020
IRQ_CRC_ERROR 0x0040
IRQ_RANGING_SLAVE_RESPONSE_DONE 0x0080
IRQ_RANGING_SLAVE_REQUEST_DISCARDED 0x0100
IRQ_RANGING_MASTER_RESULT_VALID 0x0200
IRQ_RANGING_MASTER_RESULT_TIMEOUT 0x0400
IRQ_RANGING_SLAVE_REQUEST_VALID 0x0800
IRQ_CAD_DONE 0x1000
IRQ_CAD_ACTIVITY_DETECTED 0x2000
IRQ_RX_TX_TIMEOUT 0x4000
IRQ_TX_TIMEOUT 0x4000
IRQ_RX_TIMEOUT 0x4000
IRQ_PREAMBLE_DETECTED 0x8000
IRQ_RADIO_ALL 0xFFFF
As an alternative to setting up the LoRa device with separate functions (as described above) you can use this single function;
setupLoRa(Frequency, Offset, SpreadingFactor, Bandwidth, CodeRate, Optimisation)
The function first sets the Frequency of operation, the frequency is in hertz as a 32 bit unsigned integer. The actual programmed operating frequency is the sum of Frequency and Offset (also 32 bit integer).
SpreadingFactor, Bandwidth and CodeRate are the LoRa modem parameters and the choices are as given for the setModulationParams() described above.
When using setupLoRa() that library function then calls the following functions using these defaults;
setMode(MODE_STDBY_RC)
setPacketType(PACKET_TYPE_LORA);
setRfFrequency(Frequency, Offset);
calibrateImage(0);
setModulationParams(SpreadingFactor, Bandwidth, CodeRate, LDRO_AUTO);
setBufferBaseAddress(0x00, 0x00);
setPacketParams(8, LORA_PACKET_VARIABLE_LENGTH, 255, LORA_CRC_ON, LORA_IQ_NORMAL);
setSyncWord(LORA_MAC_PRIVATE_SYNCWORD);
LORA_MAC_PUBLIC_SYNCWORD = 0x34
setHighSensitivity();
setDioIrqParams(IRQ_RADIO_ALL, IRQ_TX_DONE, 0, 0);
printModemSettings()
Prints the current modem settings to the serial monitor for diagnostic purposes. The parameters printed for LoRa are ; device_type, frequency, spreading factor, bandwidth, coding_rate, syncword, IQ_Status, preamble_length.
printOperatingSettings()
Prints the current operating settings to the serial monitor for diagnostic purposes. The settings printed are; device_type, version_number, packet_mode, header_mode, packet_CRC_on_off, AGC_auto_on_off, LNA_gain, LNA_boostHF, LNA_boostLF.
printRegisters(start, end)
Print the device registers from start address to end address.
printASCIIPacket(buff, length)
Print as ASCII characters to the serial monitor the contents of the buffer name given, for the given length.
transmit(buff, TXPacketL, timeout, TXpower, WAIT_TX)
Transmit the contents of the buffer name given, for the given length. With a time-out in mS, with a TXpower in dBm and wait for the transmit to complete (a blocking command). To have the LoRa device start transmitting and continue as a no blocking command use NO_WAIT.
With transmit and WAIT_TX the function returns the packet length if transmit detected no errors and 0 if errors were detected. If NO_WAIT is used you will need to check when pin DIO0 (SX127X) or DIO1 (SX126X and SX128X) goes high indicating transmission is completed.
CRCCCITT(buff, TXPacketL, 0xFFFF)
Calculates the 16 bit CRC of the buffer given for the length given. Specify the initialise value for the CRC, 0xFFFF in this case.
readIrqStatus()
Reads the value of the IRQ register flags.
The 4_LoRa_Receiver sketch is very similar, with the following differences;
LT.receive(RXBUFFER, RXBUFFER_SIZE, timeout, WAIT_RX)
Copy the received packet into the buffer address given with a maximum buffer size. If the RXBUFFER_SIZE is smaller than the actual received packet then the packet will be truncated. If WAIT_RX is selected then the program will wait for the time-out period (in mS) for a packet to arrive before signalling a timeout, this is a blocking command. To have the receiver wait continuously for a packet set the timeout to 0. To use the receiver in non-blocking mode set NO_WAIT in which case you will need to check DIO0 (SX127X) or DIO1 (SX126X and SX128X) going high to indicate a packet has arrived.
readPacketRSSI()
Read the signal strength in dBm of the received packet.
readPacketSNR()
Read the signal to noise ratio in dB of the received packet. Typical values are +10dB for strong signals and -20dB for reception at the limit.
printIrqStatus()
Prints to the serial monitor the interrupt flags set.
LoRa is a two way technology, each device is a transceiver. Most often on a particular frequency there will be one transmitter and one receiver. However, this may not always be the case and there could be several nodes in use on the same frequency.
In order to keep the software simple and allow for the receipt of signals from multiple receivers or directed commands to a particular node, a basic addressing scheme can be used and is implemented by some example programs, see 17_Sensor_Transmitter for an example. There are library routines to send and receive packets in addressed and non-addressed format so you choose which to send. When using addressed mode regardless of the data content of the actual payload each packet sent has 3 control bytes at the beginning of the packet. In the case of the sensor example mentioned above, the use of the addressing allows the receiver to know from which sensor transmitter the packet came.
In general the control bytes have been restricted to ASCII printable characters so that they can be shown directly on a terminal monitor. The 3 bytes are;
Packet type. This either describes the content of the packet, which could be a GPS location payload or is a command to do something and there is no payload. Details of the packet types defined are in the library file ProgramLT_Definitions.h
Packet Destination. The node number that the packet is destined for.
Packet Source. The node number that the packet was sent from.
The destination and source packet bytes mean that node ‘2’ (could be your base station receiver) can send a command that only station ‘3’ will respond to. This command could be a reset command, a request to turn on and off certain transmission types etc. Node ‘3’ can be set-up so that it only accepts commands from a particular node.
In addressed mode the 3 control bytes are automatically stripped from each received packet.
An example of the 3 control bytes from a tracker would be;
T*2
Which means there is a test packet (T) its been sent as a broadcast (*) and its from node 2.
Library fully tested on 3.3V 8Mhz ATMega328P and ATMega1284P only.
It was not the intention of this library to specifically support the large number of non-Atmel platforms. The use of platform specific hardware functions such as timers or interrupts has been avoided in the libraries, so if a hardware platform supports standard SPI and a program compiles, it should work. There are library functions that use the millis() and micros() functions. Some example programs use SoftwareSerial which is not supported on all platforms. A few programs have been tested and work on ESP32 based boards and an STM32 Xnucleo board. See the Readme for ESP32 and STM32 in the ESP32 and STM32 examples folders.
The examples do work, so if for you they do not, assume there is a problem with how you have wired the modules or that your modules are faulty or that your Arduino set-up or LoRa module is faulty or unsupported. You are best placed to diagnose these issues. It is not practical for me to provide on-going technical support for programs that are not the library examples included. This also applies to external libraries used in examples, if you have problems with these libraries, contact the authors for support.
If you find a bug, or other error in the SX12xx library or examples, and your using the ATMega328P and ATMega1284P platforms please let me know.