GPS IoT tracker board for scanning gps and environment information and sending them to an MQTT server via GPRS.
IoBroker map of the collected SnorkTracker sample.
(see https://github.com/Bastelschlumpf/SnorkView)
The hardware
The housing
The web-interface
The goal of this board is to have an easy-to-use, configurable GPS tracker that passes its data to an MQTT server. It should also be able to scan other environmental data and operate on a 12V power supply with low power consumption over a long period of time.
The main components of the systems are:
- A 'Wemos D1 mini lite' to run the software.
- A BK-808 v2 (SIM808) GPS/GPRS module to communicate with an MQTT server and to send/receive SMS.
- A BME280 module to scan environmental data.
- An LM2596 DC-DC converter to supply the GPS/GPRS board.
- An MCP1703 for the 3.3V Wemos power supply.
To interact with the board it has an easy-to-use browser interface to show the scanned values, configure the system or to debug at runtime via console. It can connect to an existing WiFi or function as an access point.
The board has a voltage divider to measure the power supply voltage and a BME280 sensor to read temperature, humidity and air pressure.
The module operates with a supply voltage of approx. 6V to 16V. Perfect for a car battery.
For power saving the supply voltage can be used to decide if the battery is charging or not and so the system can be configured to go into deep sleep mode which uses only ~0.3mA.
With the GSM chip, the system can receive SMS commands to set default values or send current information such as GPS or temperature.
The system estimates the current power consumption in mAh in energy saving mode and when the sim module is on.
You can also use the software on a esp8266 chip like the wemos d1 for having a serial console over HTTP if you connect to the D5 and D6 pin.
I don't take any responsibility nor liability for using this software nor for the installation or any tips, advice, videos, etc. given by any member of this site or any related site.
This program is licensed under GPL-3.0
The easiest way to understand what the program does is to navigate by the main source modules via the Arduino IDE or
to explore the source code via
DoxyGen generated documentation.
You can update the DoxyGen generated documentation by installing Doxygen (from http://www.doxygen.org) on your machine
and run the DoxyGen generation batch Doxygen.bat from the main folder.
- Overview of the system settings
- Switch on or off the system
- Using the sms interface
- Display system information
- Working with the console
- Firmware Update 'over the air'
- Restart the system
- Arduino IDE
- ESP8266 Board software
- ESP8266 file-system up-loader
- SnorkTracker software
- Parts from the part-list
- Micro-USB cable
- Soldering iron kit
- Multimeter
- Electronics tools
- Download Arduino IDE from
https://www.arduino.cc/en/Main/Software
and follow the installation instructions. - Install ESP8266 board software
- In Arduino IDE set 'File | Preferences' to Boards Manager URL http://arduino.esp8266.com/stable/package_esp8266com_index.json
- Open 'Tools | Board... | Boards Manager...' and search for 'esp8266' and install the software package
- Install the ESP8266 file-system up-loader from
https://github.com/esp8266/arduino-esp8266fs-plugin
and follow the installation instructions. - Download SnorkTracker software by clone or download.
- Copy the content of the snorktracker/libraries directory to the Arduino installation libraries directory. For example c:/Program Files (x86)/Arduino/libraries/
- Configure Arduino IDE
- From 'Tools | Boards' choose 'LOLIN(WEMOS) D1 mini Lite'
- Change 'Tools | Flash Size' to '1M (64k SPIFFS)'
- Change 'Tools | IwIP variant' to 'v2 Higher Bandwidth'
- Take the Breadboard and the other items from the part-list.
- First of all unsolder the (ON/OFF) pin 5 from the DC-DC module, bend it up and
solder a line to it. After that put 4 spacers under the DC-DC module and solder it
to the breadboard. Check that the bottom of the LM2596 module is not in contact with the board.
See
- Place the other parts from the part-list on the breadboard and solder it as shown.
Pay attention to the polarity of the capacitors!
Split the header connector to the length that is needed and solder it.
A header connector is needed because flashing of the Wemos module often does not work
if it is still connected to the board.
Check if the Wemos and SIM808 module has enough space and fits into the pins.
- Connect all the pins of the parts as seen on the circuit image with wires.
- The final board could look like this
- Check all the wiring with a multimeter. Also against short-circuit.
- The first step we have to do is to set the right 5V for the SIM808 module.
- For that unplug the Wemos and the SIM808 module.
- Connect a 12 power supply to the screw connector. Make sure + and - are correct!
- Switch on the LM2596 module by connecting the unsoldered pin 5 to ground.
- Now, connect the multimeter to the output pins of the DC-DC module and screw on the module resistor until the multimeter shows exactly 5.0V on the two out-pins.
- Check the pins on the female header connector for the right voltage.
- Check the 3.3V on the corresponding WEMOS pin.
- Check the 5.0V pin of the SIM808 module connector pin.
- Check the 3.3V on the BME280 module. Be aware that the ground pin is connected to the Wemos module and still open.
- Now its time to flash the software to the Wemos module.
- Unplug the Wemos module (if plugged) and connect it with the USB cable to your computer. After connecting via usb you should be able to select the arduino port under 'Tools | Port | ...'.
- Open the tracker.ino file in the tracker folder and check the Arduino environment settings.
- Upload the SPIFFS files with the 'Tools | ESP8266 Sketch data upload' menu. The SPIFFS files (htmls, styles and javascripts) are taken from the data subdirectory.
- After that go to the Config.h file of the project and enter the right configuration values.
- Now we can flash the program to the Wemos chip by clicking 'Sketch | upload'
- Unplug and plug again the Wemos module to the usb cable and start immediately the serial monitor of the Arduino IDE 'Tools | Serial monitor'.
- If everything is correct you can see an access-point in the WiFi of your computer and you can connect to the browser interface by calling the ip in your browser. The software works in a captive way, so you can enter a dummy (not https) url and the system should redirect you to the web interface. For example http://dummy.com If this does not work find out the new ip via your WiFi router interface.
- If the software works fine on the usb cable then you can plug the wemos into the board and connect a power supply. Check again the connectivity.
- The software in the Wemos module creates a web-server in station and/or in access-point mode.
- The analog input of the wemos is connected to the middle of the two voltage divider resistors. So it can read the power supply voltage of the system (for example the car battery voltage).
- The software can be configured to recognize a charging or discharging car battery to switch on or off the
submodules. With my car this was:
- 11.8 Volt if the car was switched off for more than a day.
- 14.2 Volt if the engine is running.
- 13.3 Volt after switching off the engine.
- A BME280 sensor is connected to the 3.3V power and can be switched on by setting the D4 pin of the wemos chip to ground. This is done only from time to time to save energy.
- There is an LM2596 DC-DC module on the board which can be switched on by a '-' signal to the pin 5 of the LM2596. Behind the DC-DC module there is a SIM808 module with GPS/GPRS/GSM functionality. So the Wemos can switch on/off the SIM808 chip to save energy.
- The Wemos chip can communicate with the SIM808 module via RX and TX signal and AT commands.
- Via the GPRS module it can send the scanned data to a MQTT server and can communicate via SMS to a phone.
| Label | Part Type | Properties |
|---|---|---|
| Breadboard | Double sided PCB board | 24 x 18 holes |
| Power connector | Mount screw connector | 2 pins |
| Header connector | Female header connector | 3 x 9 pins |
| wire | colored breadboard wire | i.e. 0.14 mm2 |
| 12V Plug | Cigarette Lighter Power | 12V To 5.5 x 2.1mm |
| Panel Jack | Jack Socket Female | 5.5 x 2.1mm |
| V1 | VC Power | 6V - 16V |
| WeMos D1 Mini lite | WeMos D1 Mini lite | ESP8295 |
| BK-808v2 | BK-808 v2 | www.and-global.com |
| GPS Antenna | Embedded GPS Antenna | uFL connector |
| GSM Antenna | Embedded GSM Antenna | uFL connector |
| SIM card | SIM card for sms/data | with deposit |
| BME280 | BME280 | 3.3V |
| LM1 | LM2596 | adjustable module |
| U2 | Voltage Regulator 3.3V | MCP1703T-3302E |
| C1 | Electrolytic Capacitor | 1uF (16V) |
| C2 | Electrolytic Capacitor | 1uF (16V) |
| C3 | Ceramic Capacitor | 100 nF (16V) |
| C4 | Ceramic Capacitor | 100 nF (16V) |
| R1 | Resistor | 680 kOhm |
| R2 | Resistor | 100 kOhm |
| R3 | Resistor | 4.7 kOhm |
Here are some sample shopping items. Please check the details if everything is correct.
Some of the items are sets for further projects. You can also buy cheaper single items. The material price should be between 50$ and 100$.
- https://www.arduino.cc Thanks to the Arduino community with all its incredible possibilities and support.*
- https://github.com/arendst/Sonoff-Tasmota Thanks to Theo Arends for his great home automation software project with all the detailed esp functionality.
- http://fritzing.org/home Thanks to the fritzing team for this very intuitive usable software. I could create my circuit in Fritzing with only a half day.
- https://marketplace.visualstudio.com/items?itemName=MadsKristensen.MarkdownEditor Thanks to Mads Kristensen for his helpful Visual Studio MarkDown PlugIn.*
- And a special thanks goes to my brother for all the hours he spent helping me with the electronic circuit.