Modbus library for STM32 Microcontrollers

TCP, USART and USB-CDC Modbus RTU Master and Slave library for STM32 microcontrollers based on Cube HAL and FreeRTOS.

Includes multiple examples for popular development boards including BluePill, NUCLEO-64, NUCLEO-144 and Discovery Boards (Cortex-M3/M4/M7).

This is a port of the Modbus library for Arduino: https://github.com/smarmengol/Modbus-Master-Slave-for-Arduino

Video demo for STM32F4-discovery board and TouchGFX: https://youtu.be/XDCQvu0LirY

NEW Script examples to test the library based on Pymodbus

NEW TCP slave (server) multi-client with configurable auto-aging algorithm for management of TCP connections

Translations supported by the community:

Traditional Chinese: 繁體中文

Characteristics:

Portable to any STM32 MCU supported by ST Cube HAL.
Portable to other Microcontrollers, like the Raspberry PI Pico, requiring little engineering effort.
Multithread-safe implementation based on FreeRTOS.
Multiple instances of Modbus (Master and/or Slave) can run concurrently in the same MCU, only limited by the number of available UART/USART of the MCU.
RS232 and RS485 compatible.
USART DMA support for high baudrates with idle-line detection.
USB-CDC RTU master and Slave support for F103 Bluepill board.
TCP master and slave support with examples for F429 and H743 MCUs

File structure

├── LICENSE
├── README.md
├── Examples
    ├── ModbusBluepill --> STM32F103C8 USART Slave
    ├── ModbusBluepillUSB --> STM32F103C8 USART + USB-CDC Master and Slave 
    ├── ModbusF103 --> NUCLEO-F103RB Modbus Master and Slave
    ├── ModbusF429 --> NUCLEO-F429ZI Modbus Slave 
    ├── ModbusF429TCP --> NUCLEO-F429ZI Modbus TCP
    ├── ModbusF429DMA --> NUCLEO-F429ZI Modbus RTU DMA master and slave 
    ├── ModbusL152DMA --> NUCLEO-L152RE Modbus RTU DMA slave
    ├── ModbusH743 --> NUCLEO-H743ZI Modbus Slave
    ├── ModbusH743TCP --> NUCLEO-H743ZI Modbus TCP
    ├── ModbusF303 --> NUCLEO-F303RE Modbus Slave
    ├── ModbusSTM32F4-discovery --> STM32F4-discovery TouchGFX + Modbus Master
    ├── ModbusWB55DMA --> P-NUCLEO-WB55 Modbus RTU DMA slave with RS485 
    ├── ModbusG070 --> NUCLEO-G070RB Modbus Slave
    ├── ModbusF030 --> STM32F030RCT6 USART Slave
├── Script
    ├── *.ipynb --> various master and slave Jupyter notebooks for testing
├── MODBUS-LIB --> Library Folder
    ├── Inc
    │   └── Modbus.h 
    ├── Config
    │   └── ModbusConfigTemplate.h --> Configuration Template
    └── Src
        ├── Modbus.c 
        └── UARTCallback.c

How to use the examples

Examples provided for STM32CubeIDE Version: 1.8.0 https://www.st.com/en/development-tools/stm32cubeide.html.

Import the examples in the STM32Cube IDE from the system folder
Connect your NUCLEO board
Compile and start your debugging session!
If you need to adjust the Baud rate or any other parameter use the Cube-MX assistant (recommended). If you change the USART port you need to enable the interrupts for the selected USART. Check UARTCallback.c for more details.

Notes and Known issues :

The standard interrupt mode for Modbus RTU USART is suitable for 115200 bps or lower baud rates. For Higher baud rates---tested up to 2 Mbps---it is recommended to use the DMA mode. Check the corresponding examples. It will require extra configurations for the DMA channels in the Cube HAL.
The USB-CDC example supports only the Bluepill development board. It has not been validated with other development boards. To use this example, you need to activate USB-CDC in your ModbusConfig.h file.
The TCP examples have been validated with NUCLEO F429ZI and H743ZI. To use these examples, you need to activate TCP in your ModbusConfig.h file.
The HAL implementation for LWIP TCP of the CubeMX generates code that might not work if the cable is not connected from the very beginning. This is a known issue that can be solved manually changing the generated code as detailed here: https://community.st.com/s/question/0D50X0000CDolzDSQR/ethernet-does-not-work-if-uc-starts-with-the-cable-disconnected

Check the TCP example for the NUCLEO F429, which includes the manual modifications.

How to port to your own MCU

Create a new project in STM32Cube IDE for your MCU
Enable FreeRTOS CMSIS_V2 in the middleware section of Cube-MX
Configure a USART and activate the global interrupt
If you are using the DMA mode for USART, configure the DMA requests for RX and TX
Configure the Preemption priority of USART interrupt to a lower priority (5 or a higher number for a standard configuration) than your FreeRTOS scheduler. This parameter is changed in the NVIC configuration pane.
Import the Modbus library folder (MODBUS-LIB) using drag-and-drop from your host operating system to your STM32Cube IDE project
When asked, choose link folders and files
Update the include paths in the project's properties to include the Inc folder of MODBUS-LIB folder
Create a ModbusConfig.h using the ModbusConfigTemplate.h and add it to your project in your include path
Instantiate a new global modbusHandler_t and follow the examples provided in the repository
Note: If your project uses the USART interrupt service for other purposes you have to modify the UARTCallback.c file accordingly

Recommended Modbus Master and Slave testing tools for Linux and Windows

TODOs:

Implement isolated memory spaces for coils, inputs and holding registers.
Implement wrapper functions for Master function codes. Currently, telegrams are defined manually.
Improve function documentation
~~MODBUS TCP implementation improvement to support multiple clients and TCP session management~~ (10/24/2021)
~~Improve the queue for data reception; the current method is too heavy it should be replaced with a simple buffer, a stream, or another FreeRTOS primitive.~~ Solved Queue replaced by a Ring Buffer (03/19/2021)
~~Test with Rs485 transceivers (implemented but not tested)~~ Verified with MAX485 transceivers (01/03/2021)
~~MODBUS TCP implementation~~ (28/04/2021)

IvanPletnev/Modbus-STM32-HAL-FreeRTOS