RX_SIGNAL_BAR is gone
zhaoparrot opened this issue · 2 comments
zhaoparrot commented
I have MDC1200 enabled (D live OFF)and the rx bar is gone, thinking it may be related to
#ifdef ENABLE_MDC1200
if (mdc1200_rx_ready_tick_500ms > 0)
{
g_center_line = CENTER_LINE_MDC1200;
so i try disable MDC1200
RXbar still no show
my makefile ↓
ENABLE_CLANG := 0
ENABLE_SWD := 0
ENABLE_OVERLAY := 0
ENABLE_LTO := 1
# UART Programming 2.9 kB
ENABLE_UART := 1
ENABLE_UART_DEBUG := 0
# AirCopy 2.5 kB
ENABLE_AIRCOPY := 0
ENABLE_AIRCOPY_REMEMBER_FREQ := 0
ENABLE_AIRCOPY_RX_REBOOT := 0
# FM Radio 4.2 kB
ENABLE_FMRADIO_64_76 := 0
ENABLE_FMRADIO_76_90 := 0
ENABLE_FMRADIO_76_108 := 0
ENABLE_FMRADIO_875_108 := 0
ENABLE_FMRADIO_64_108 := 0
# NOAA 1.2 kB
ENABLE_NOAA := 0
# Voice 1.7 kB
ENABLE_VOICE := 0
ENABLE_MUTE_RADIO_FOR_VOICE := 0
# Tx on Voice 1.0 kB
ENABLE_VOX := 0
ENABLE_REDUCE_LOW_MID_TX_POWER := 1
# Tx Alarm 600 B
ENABLE_ALARM := 0
ENABLE_TX1750 := 0
# MDC1200 2.8 kB
ENABLE_MDC1200 := 0
ENABLE_PWRON_PASSWORD := 0
ENABLE_RESET_AES_KEY := 0
ENABLE_BIG_FREQ := 1
# smaa bolf 580 B
ENABLE_SMALL_BOLD := 1
# smallest font 2 kB
ENABLE_SMALLEST_FONT := 1
# trim trailing 44 B
ENABLE_TRIM_TRAILING_ZEROS := 0
ENABLE_KEEP_MEM_NAME := 1
ENABLE_WIDE_RX := 0
ENABLE_TX_WHEN_AM := 0
# Freq calibration 188 B
ENABLE_F_CAL_MENU := 0
ENABLE_TX_UNLOCK := 0
ENABLE_CTCSS_TAIL_PHASE_SHIFT := 0
ENABLE_CONTRAST := 0
ENABLE_BOOT_BEEPS := 0
ENABLE_DTMF_CALL_FLASH_LIGHT := 0
ENABLE_FLASH_LIGHT_SOS_TONE := 0
ENABLE_SHOW_CHARGE_LEVEL := 0
ENABLE_REVERSE_BAT_SYMBOL := 0
ENABLE_FREQ_SEARCH_TIMEOUT := 0
ENABLE_CODE_SEARCH_TIMEOUT := 0
# Kill and Revive 400 B
ENABLE_KILL_REVIVE := 0
# AM Fix 800 B
ENABLE_AM_FIX := 1
ENABLE_AM_FIX_SHOW_DATA := 0
# Squelch 12 B .. can't be right ?
ENABLE_SQUELCH_MORE_SENSITIVE := 1
ENABLE_SQ_OPEN_WITH_UP_DN_BUTTS := 1
ENABLE_FASTER_CHANNEL_SCAN := 1
ENABLE_COPY_CHAN_TO_VFO_TO_CHAN := 1
# Rx Signal Bar 400 B
ENABLE_RX_SIGNAL_BAR := 1
# Tx Timeout Bar 200 B
ENABLE_TX_TIMEOUT_BAR := 0
# Tx Audio Bar 300 B
ENABLE_TX_AUDIO_BAR := 0
# Side Button Menu 300 B
ENABLE_SIDE_BUTT_MENU := 0
# Key Lock 400 B
ENABLE_KEYLOCK := 1
#ENABLE_PANADAPTER := 0
#ENABLE_SINGLE_VFO_CHAN := 0
by the way MDC1200 does not take 2.8 kB flash in my test, more like 2.3kB to me .
OneOfEleven commented
There are menu options to enable/disable the TX and TX bars, somewhere around menu number 33 or so. check to make sure the RX bar menu is set to ON.
zhaoparrot commented
Ah! it's a menu option now , good to know . works fine then. thanks.