Using Bluepill and STM32 Arduino Official Core (SPI1 REMAP)
rtek1000 opened this issue · 0 comments
rtek1000 commented
Using the official core: https://github.com/stm32duino/Arduino_Core_STM32
(Open your browser and enter IP: 192.168.1.203)
rbbb_server.ino (Modified)
// This is a demo of the RBBB running as webserver with the Ether Card
// 2010-05-28 <jc@wippler.nl> http://opensource.org/licenses/mit-license.php
//
//
//-----------------------------------------------------------------
// Ported to STM32F103 by Vassilis Serasidis on 21 May 2015
// Home: http://www.serasidis.gr
// email: avrsite@yahoo.gr
//
// PIN Connections (Using STM32F103):
//
// ENC28J60 - STM32F103
// VCC - 3.3V
// RESET - Pin PB10
// GND - GND
// SCK - Pin PB3
// SO - Pin PB4
// SI - Pin PB5
// CS - Pin PA15
//-----------------------------------------------------------------
//
//
#include <EtherCard_STM.h>
#include <SPI.h>
// ethernet interface mac address, must be unique on the LAN
static byte mymac[] = { 0x74, 0x69, 0x69, 0x2D, 0x30, 0x31 };
static byte myip[] = { 192, 168, 1, 203 };
byte Ethernet::buffer[500];
BufferFiller bfill;
#define ENC28J60_RESET PB10
void setup () {
STM32F103CBT6_Init();
pinMode(ENC28J60_RESET, OUTPUT);
digitalWrite(ENC28J60_RESET, LOW);
delay(1);
digitalWrite(ENC28J60_RESET, HIGH);
Serial.begin(9600);
delay(10);
if (ether.begin(sizeof Ethernet::buffer, mymac) == 0)
Serial.println(F("Failed to access Ethernet controller"));
ether.staticSetup(myip);
//if (!ether.dhcpSetup())
// Serial.println("DHCP failed");
ether.printIp("IP: ", ether.myip);
ether.printIp("GW: ", ether.gwip);
ether.printIp("DNS: ", ether.dnsip);
}
static word homePage() {
long t = millis() / 1000;
word h = t / 3600;
byte m = (t / 60) % 60;
byte s = t % 60;
bfill = ether.tcpOffset();
bfill.emit_p(PSTR(
"HTTP/1.0 200 OK\r\n"
"Content-Type: text/html\r\n"
"Pragma: no-cache\r\n"
"\r\n"
"<meta http-equiv='refresh' content='1'/>"
"<title>RBBB server</title>"
"<h1>$D$D:$D$D:$D$D</h1>"),
h / 10, h % 10, m / 10, m % 10, s / 10, s % 10);
return bfill.position();
}
void loop () {
if (ether.packetLoop(ether.packetReceive())) { // check if valid tcp data is received
ether.httpServerReply(homePage()); // send web page data
}
}
void STM32F103CBT6_Init() {
//REMAP UART:
Serial.setRx(PA10); // using pin name PY_n
Serial.setTx(PA9); // using pin number PYn
//REMAP SPI:
SPI.setMOSI(PB5); // using pin number PYn
SPI.setMISO(PB4); // using pin name PY_n
SPI.setSCLK(PB3); // using pin number PYn
SPI.setSSEL(PA15); // using pin number PYn
}enc28j60.cpp (Modified, added SPI speed: 35MHz for bluepill; default CS pin: SS)
// Microchip ENC28J60 Ethernet Interface Driver
// Author: Guido Socher
// Copyright: GPL V2
//
// Based on the enc28j60.c file from the AVRlib library by Pascal Stang.
// For AVRlib See http://www.procyonengineering.com/
// Used with explicit permission of Pascal Stang.
//
// 2010-05-20 <jc@wippler.nl>
//
//-----------------------------------------------------------------
// Ported to STM32F103 by Vassilis Serasidis on 21 May 2015
// Home: http://www.serasidis.gr
// email: avrsite@yahoo.gr
//-----------------------------------------------------------------
#if ARDUINO >= 100
#include <Arduino.h> // Arduino 1.0
#else
#include <Wprogram.h> // Arduino 0022
#endif
#include "enc28j60.h"
#include <SPI.h> // Using library SPI in folder: D:\Documents\Arduino\hardware\STM32\STM32F1XX\libraries\SPI
uint16_t ENC28J60::bufferSize;
bool ENC28J60::broadcast_enabled = false;
#define SPI_SPEED 35000000 // 35MHz bluepill
// ENC28J60 Control Registers
// Control register definitions are a combination of address,
// bank number, and Ethernet/MAC/PHY indicator bits.
// - Register address (bits 0-4)
// - Bank number (bits 5-6)
// - MAC/PHY indicator (bit 7)
#define ADDR_MASK 0x1F
#define BANK_MASK 0x60
#define SPRD_MASK 0x80
// All-bank registers
#define EIE 0x1B
#define EIR 0x1C
#define ESTAT 0x1D
#define ECON2 0x1E
#define ECON1 0x1F
// Bank 0 registers
#define ERDPT (0x00|0x00)
#define EWRPT (0x02|0x00)
#define ETXST (0x04|0x00)
#define ETXND (0x06|0x00)
#define ERXST (0x08|0x00)
#define ERXND (0x0A|0x00)
#define ERXRDPT (0x0C|0x00)
// #define ERXWRPT (0x0E|0x00)
#define EDMAST (0x10|0x00)
#define EDMAND (0x12|0x00)
// #define EDMADST (0x14|0x00)
#define EDMACS (0x16|0x00)
// Bank 1 registers
#define EHT0 (0x00|0x20)
#define EHT1 (0x01|0x20)
#define EHT2 (0x02|0x20)
#define EHT3 (0x03|0x20)
#define EHT4 (0x04|0x20)
#define EHT5 (0x05|0x20)
#define EHT6 (0x06|0x20)
#define EHT7 (0x07|0x20)
#define EPMM0 (0x08|0x20)
#define EPMM1 (0x09|0x20)
#define EPMM2 (0x0A|0x20)
#define EPMM3 (0x0B|0x20)
#define EPMM4 (0x0C|0x20)
#define EPMM5 (0x0D|0x20)
#define EPMM6 (0x0E|0x20)
#define EPMM7 (0x0F|0x20)
#define EPMCS (0x10|0x20)
// #define EPMO (0x14|0x20)
#define EWOLIE (0x16|0x20)
#define EWOLIR (0x17|0x20)
#define ERXFCON (0x18|0x20)
#define EPKTCNT (0x19|0x20)
// Bank 2 registers
#define MACON1 (0x00|0x40|0x80)
#define MACON2 (0x01|0x40|0x80)
#define MACON3 (0x02|0x40|0x80)
#define MACON4 (0x03|0x40|0x80)
#define MABBIPG (0x04|0x40|0x80)
#define MAIPG (0x06|0x40|0x80)
#define MACLCON1 (0x08|0x40|0x80)
#define MACLCON2 (0x09|0x40|0x80)
#define MAMXFL (0x0A|0x40|0x80)
#define MAPHSUP (0x0D|0x40|0x80)
#define MICON (0x11|0x40|0x80)
#define MICMD (0x12|0x40|0x80)
#define MIREGADR (0x14|0x40|0x80)
#define MIWR (0x16|0x40|0x80)
#define MIRD (0x18|0x40|0x80)
// Bank 3 registers
#define MAADR1 (0x00|0x60|0x80)
#define MAADR0 (0x01|0x60|0x80)
#define MAADR3 (0x02|0x60|0x80)
#define MAADR2 (0x03|0x60|0x80)
#define MAADR5 (0x04|0x60|0x80)
#define MAADR4 (0x05|0x60|0x80)
#define EBSTSD (0x06|0x60)
#define EBSTCON (0x07|0x60)
#define EBSTCS (0x08|0x60)
#define MISTAT (0x0A|0x60|0x80)
#define EREVID (0x12|0x60)
#define ECOCON (0x15|0x60)
#define EFLOCON (0x17|0x60)
#define EPAUS (0x18|0x60)
// ENC28J60 ERXFCON Register Bit Definitions
#define ERXFCON_UCEN 0x80
#define ERXFCON_ANDOR 0x40
#define ERXFCON_CRCEN 0x20
#define ERXFCON_PMEN 0x10
#define ERXFCON_MPEN 0x08
#define ERXFCON_HTEN 0x04
#define ERXFCON_MCEN 0x02
#define ERXFCON_BCEN 0x01
// ENC28J60 EIE Register Bit Definitions
#define EIE_INTIE 0x80
#define EIE_PKTIE 0x40
#define EIE_DMAIE 0x20
#define EIE_LINKIE 0x10
#define EIE_TXIE 0x08
#define EIE_WOLIE 0x04
#define EIE_TXERIE 0x02
#define EIE_RXERIE 0x01
// ENC28J60 EIR Register Bit Definitions
#define EIR_PKTIF 0x40
#define EIR_DMAIF 0x20
#define EIR_LINKIF 0x10
#define EIR_TXIF 0x08
#define EIR_WOLIF 0x04
#define EIR_TXERIF 0x02
#define EIR_RXERIF 0x01
// ENC28J60 ESTAT Register Bit Definitions
#define ESTAT_INT 0x80
#define ESTAT_LATECOL 0x10
#define ESTAT_RXBUSY 0x04
#define ESTAT_TXABRT 0x02
#define ESTAT_CLKRDY 0x01
// ENC28J60 ECON2 Register Bit Definitions
#define ECON2_AUTOINC 0x80
#define ECON2_PKTDEC 0x40
#define ECON2_PWRSV 0x20
#define ECON2_VRPS 0x08
// ENC28J60 ECON1 Register Bit Definitions
#define ECON1_TXRST 0x80
#define ECON1_RXRST 0x40
#define ECON1_DMAST 0x20
#define ECON1_CSUMEN 0x10
#define ECON1_TXRTS 0x08
#define ECON1_RXEN 0x04
#define ECON1_BSEL1 0x02
#define ECON1_BSEL0 0x01
// ENC28J60 MACON1 Register Bit Definitions
#define MACON1_LOOPBK 0x10
#define MACON1_TXPAUS 0x08
#define MACON1_RXPAUS 0x04
#define MACON1_PASSALL 0x02
#define MACON1_MARXEN 0x01
// ENC28J60 MACON2 Register Bit Definitions
#define MACON2_MARST 0x80
#define MACON2_RNDRST 0x40
#define MACON2_MARXRST 0x08
#define MACON2_RFUNRST 0x04
#define MACON2_MATXRST 0x02
#define MACON2_TFUNRST 0x01
// ENC28J60 MACON3 Register Bit Definitions
#define MACON3_PADCFG2 0x80
#define MACON3_PADCFG1 0x40
#define MACON3_PADCFG0 0x20
#define MACON3_TXCRCEN 0x10
#define MACON3_PHDRLEN 0x08
#define MACON3_HFRMLEN 0x04
#define MACON3_FRMLNEN 0x02
#define MACON3_FULDPX 0x01
// ENC28J60 MICMD Register Bit Definitions
#define MICMD_MIISCAN 0x02
#define MICMD_MIIRD 0x01
// ENC28J60 MISTAT Register Bit Definitions
#define MISTAT_NVALID 0x04
#define MISTAT_SCAN 0x02
#define MISTAT_BUSY 0x01
// ENC28J60 EBSTCON Register Bit Definitions
#define EBSTCON_PSV2 0x80
#define EBSTCON_PSV1 0x40
#define EBSTCON_PSV0 0x20
#define EBSTCON_PSEL 0x10
#define EBSTCON_TMSEL1 0x08
#define EBSTCON_TMSEL0 0x04
#define EBSTCON_TME 0x02
#define EBSTCON_BISTST 0x01
// PHY registers
#define PHCON1 0x00
#define PHSTAT1 0x01
#define PHHID1 0x02
#define PHHID2 0x03
#define PHCON2 0x10
#define PHSTAT2 0x11
#define PHIE 0x12
#define PHIR 0x13
#define PHLCON 0x14
// ENC28J60 PHY PHCON1 Register Bit Definitions
#define PHCON1_PRST 0x8000
#define PHCON1_PLOOPBK 0x4000
#define PHCON1_PPWRSV 0x0800
#define PHCON1_PDPXMD 0x0100
// ENC28J60 PHY PHSTAT1 Register Bit Definitions
#define PHSTAT1_PFDPX 0x1000
#define PHSTAT1_PHDPX 0x0800
#define PHSTAT1_LLSTAT 0x0004
#define PHSTAT1_JBSTAT 0x0002
// ENC28J60 PHY PHCON2 Register Bit Definitions
#define PHCON2_FRCLINK 0x4000
#define PHCON2_TXDIS 0x2000
#define PHCON2_JABBER 0x0400
#define PHCON2_HDLDIS 0x0100
// ENC28J60 Packet Control Byte Bit Definitions
#define PKTCTRL_PHUGEEN 0x08
#define PKTCTRL_PPADEN 0x04
#define PKTCTRL_PCRCEN 0x02
#define PKTCTRL_POVERRIDE 0x01
// SPI operation codes
#define ENC28J60_READ_CTRL_REG 0x00
#define ENC28J60_READ_BUF_MEM 0x3A
#define ENC28J60_WRITE_CTRL_REG 0x40
#define ENC28J60_WRITE_BUF_MEM 0x7A
#define ENC28J60_BIT_FIELD_SET 0x80
#define ENC28J60_BIT_FIELD_CLR 0xA0
#define ENC28J60_SOFT_RESET 0xFF
// The RXSTART_INIT must be zero. See Rev. B4 Silicon Errata point 5.
// Buffer boundaries applied to internal 8K ram
// the entire available packet buffer space is allocated
#define RXSTART_INIT 0x0000 // start of RX buffer, room for 2 packets
#define RXSTOP_INIT 0x0BFF // end of RX buffer
#define TXSTART_INIT 0x0C00 // start of TX buffer, room for 1 packet
#define TXSTOP_INIT 0x11FF // end of TX buffer
#define SCRATCH_START 0x1200 // start of scratch area
#define SCRATCH_LIMIT 0x2000 // past end of area, i.e. 3.5 Kb
#define SCRATCH_PAGE_SHIFT 6 // addressing is in pages of 64 bytes
#define SCRATCH_PAGE_SIZE (1 << SCRATCH_PAGE_SHIFT)
// max frame length which the conroller will accept:
// (note: maximum ethernet frame length would be 1518)
#define MAX_FRAMELEN 1500
#define FULL_SPEED 1 // switch to full-speed SPI for bulk transfers
static byte Enc28j60Bank;
static int gNextPacketPtr;
static byte selectPin;
void ENC28J60::initSPI () {
SPI.begin();
SPI.setBitOrder(MSBFIRST);
//SPI.setDataMode(SPI_MODE0);
//SPI.setClockDivider(SPI_CLOCK_DIV16);
}
static void enableChip () {
//cli();
digitalWrite(selectPin, LOW);
}
static void disableChip () {
digitalWrite(selectPin, HIGH);
//sei();
}
//static void xferSPI (byte data) {
//SPDR = data;
//while (!(SPSR&(1<<SPIF)))
//}
static byte readOp (byte op, byte address) {
enableChip();
byte result;
//xferSPI(op | (address & ADDR_MASK));
//xferSPI(0x00);
//if (address & 0x80)
// xferSPI(0x00);
//byte result = SPDR;
SPI.beginTransaction(SPISettings(SPI_SPEED, MSBFIRST, SPI_MODE0));
SPI.transfer(op | (address & ADDR_MASK));
result = SPI.transfer(0x00);
if (address & 0x80)
result = SPI.transfer(0x00);
SPI.endTransaction();
disableChip();
return result;
}
static void writeOp (byte op, byte address, byte data) {
enableChip();
//xferSPI(op | (address & ADDR_MASK));
//xferSPI(data);
SPI.beginTransaction(SPISettings(SPI_SPEED, MSBFIRST, SPI_MODE0));
SPI.transfer(op | (address & ADDR_MASK));
SPI.transfer(data);
SPI.endTransaction();
disableChip();
}
static void readBuf(uint16_t len, byte* data) {
enableChip();
//xferSPI(ENC28J60_READ_BUF_MEM);
SPI.beginTransaction(SPISettings(SPI_SPEED, MSBFIRST, SPI_MODE0));
SPI.transfer(ENC28J60_READ_BUF_MEM);
while (len--) {
//xferSPI(0x00);
//*data++ = SPDR;
*data++ = SPI.transfer(0x00);
}
SPI.endTransaction();
disableChip();
}
static void writeBuf(uint16_t len, const byte* data) {
enableChip();
//xferSPI(ENC28J60_WRITE_BUF_MEM);
SPI.beginTransaction(SPISettings(SPI_SPEED, MSBFIRST, SPI_MODE0));
SPI.transfer(ENC28J60_WRITE_BUF_MEM);
//while (len--)
// xferSPI(*data++);
while (len--)
SPI.transfer(*data++);
SPI.endTransaction();
disableChip();
}
static void SetBank (byte address) {
if ((address & BANK_MASK) != Enc28j60Bank) {
writeOp(ENC28J60_BIT_FIELD_CLR, ECON1, ECON1_BSEL1|ECON1_BSEL0);
Enc28j60Bank = address & BANK_MASK;
writeOp(ENC28J60_BIT_FIELD_SET, ECON1, Enc28j60Bank>>5);
}
}
static byte readRegByte (byte address) {
SetBank(address);
return readOp(ENC28J60_READ_CTRL_REG, address);
}
static uint16_t readReg(byte address) {
return readRegByte(address) + (readRegByte(address+1) << 8);
}
static void writeRegByte (byte address, byte data) {
SetBank(address);
writeOp(ENC28J60_WRITE_CTRL_REG, address, data);
}
static void writeReg(byte address, uint16_t data) {
writeRegByte(address, data);
writeRegByte(address + 1, data >> 8);
}
static uint16_t readPhyByte (byte address) {
writeRegByte(MIREGADR, address);
writeRegByte(MICMD, MICMD_MIIRD);
while (readRegByte(MISTAT) & MISTAT_BUSY)
;
writeRegByte(MICMD, 0x00);
return readRegByte(MIRD+1);
}
static void writePhy (byte address, uint16_t data) {
writeRegByte(MIREGADR, address);
writeReg(MIWR, data);
while (readRegByte(MISTAT) & MISTAT_BUSY)
;
}
byte ENC28J60::initialize (uint16_t size, const byte* macaddr, byte csPin) {
bufferSize = size;
//if (bitRead(SPCR, SPE) == 0)
initSPI();
selectPin = csPin;
pinMode(selectPin, OUTPUT);
disableChip();
writeOp(ENC28J60_SOFT_RESET, 0, ENC28J60_SOFT_RESET);
delay(2); // errata B7/2
while (!readOp(ENC28J60_READ_CTRL_REG, ESTAT) & ESTAT_CLKRDY)
;
gNextPacketPtr = RXSTART_INIT;
writeReg(ERXST, RXSTART_INIT);
writeReg(ERXRDPT, RXSTART_INIT);
writeReg(ERXND, RXSTOP_INIT);
writeReg(ETXST, TXSTART_INIT);
writeReg(ETXND, TXSTOP_INIT);
enableBroadcast(); // change to add ERXFCON_BCEN recommended by epam
writeReg(EPMM0, 0x303f);
writeReg(EPMCS, 0xf7f9);
writeRegByte(MACON1, MACON1_MARXEN|MACON1_TXPAUS|MACON1_RXPAUS);
writeRegByte(MACON2, 0x00);
writeOp(ENC28J60_BIT_FIELD_SET, MACON3,
MACON3_PADCFG0|MACON3_TXCRCEN|MACON3_FRMLNEN);
writeReg(MAIPG, 0x0C12);
writeRegByte(MABBIPG, 0x12);
writeReg(MAMXFL, MAX_FRAMELEN);
writeRegByte(MAADR5, macaddr[0]);
writeRegByte(MAADR4, macaddr[1]);
writeRegByte(MAADR3, macaddr[2]);
writeRegByte(MAADR2, macaddr[3]);
writeRegByte(MAADR1, macaddr[4]);
writeRegByte(MAADR0, macaddr[5]);
writePhy(PHCON2, PHCON2_HDLDIS);
SetBank(ECON1);
writeOp(ENC28J60_BIT_FIELD_SET, EIE, EIE_INTIE|EIE_PKTIE);
writeOp(ENC28J60_BIT_FIELD_SET, ECON1, ECON1_RXEN);
byte rev = readRegByte(EREVID);
// microchip forgot to step the number on the silcon when they
// released the revision B7. 6 is now rev B7. We still have
// to see what they do when they release B8. At the moment
// there is no B8 out yet
if (rev > 5) ++rev;
return rev;
}
bool ENC28J60::isLinkUp() {
return (readPhyByte(PHSTAT2) >> 2) & 1;
}
void ENC28J60::packetSend(uint16_t len) {
while (readOp(ENC28J60_READ_CTRL_REG, ECON1) & ECON1_TXRTS)
if (readRegByte(EIR) & EIR_TXERIF) {
writeOp(ENC28J60_BIT_FIELD_SET, ECON1, ECON1_TXRST);
writeOp(ENC28J60_BIT_FIELD_CLR, ECON1, ECON1_TXRST);
}
writeReg(EWRPT, TXSTART_INIT);
writeReg(ETXND, TXSTART_INIT+len);
writeOp(ENC28J60_WRITE_BUF_MEM, 0, 0x00);
writeBuf(len, buffer);
writeOp(ENC28J60_BIT_FIELD_SET, ECON1, ECON1_TXRTS);
}
uint16_t ENC28J60::packetReceive() {
uint16_t len = 0;
if (readRegByte(EPKTCNT) > 0) {
writeReg(ERDPT, gNextPacketPtr);
struct {
uint16_t nextPacket;
uint16_t byteCount;
uint16_t status;
} header;
readBuf(sizeof header, (byte*) &header);
gNextPacketPtr = header.nextPacket;
len = header.byteCount - 4; //remove the CRC count
if (len>bufferSize-1)
len=bufferSize-1;
if ((header.status & 0x80)==0)
len = 0;
else
readBuf(len, buffer);
buffer[len] = 0;
if (gNextPacketPtr - 1 > RXSTOP_INIT)
writeReg(ERXRDPT, RXSTOP_INIT);
else
writeReg(ERXRDPT, gNextPacketPtr - 1);
writeOp(ENC28J60_BIT_FIELD_SET, ECON2, ECON2_PKTDEC);
}
return len;
}
void ENC28J60::copyout (byte page, const byte* data) {
uint16_t destPos = SCRATCH_START + (page << SCRATCH_PAGE_SHIFT);
if (destPos < SCRATCH_START || destPos > SCRATCH_LIMIT - SCRATCH_PAGE_SIZE)
return;
writeReg(EWRPT, destPos);
writeBuf(SCRATCH_PAGE_SIZE, data);
}
void ENC28J60::copyin (byte page, byte* data) {
uint16_t destPos = SCRATCH_START + (page << SCRATCH_PAGE_SHIFT);
if (destPos < SCRATCH_START || destPos > SCRATCH_LIMIT - SCRATCH_PAGE_SIZE)
return;
writeReg(ERDPT, destPos);
readBuf(SCRATCH_PAGE_SIZE, data);
}
byte ENC28J60::peekin (byte page, byte off) {
byte result = 0;
uint16_t destPos = SCRATCH_START + (page << SCRATCH_PAGE_SHIFT) + off;
if (SCRATCH_START <= destPos && destPos < SCRATCH_LIMIT) {
writeReg(ERDPT, destPos);
readBuf(1, &result);
}
return result;
}
// Contributed by Alex M. Based on code from: http://blog.derouineau.fr
// /2011/07/putting-enc28j60-ethernet-controler-in-sleep-mode/
void ENC28J60::powerDown() {
writeOp(ENC28J60_BIT_FIELD_CLR, ECON1, ECON1_RXEN);
while(readRegByte(ESTAT) & ESTAT_RXBUSY);
while(readRegByte(ECON1) & ECON1_TXRTS);
writeOp(ENC28J60_BIT_FIELD_SET, ECON2, ECON2_VRPS);
writeOp(ENC28J60_BIT_FIELD_SET, ECON2, ECON2_PWRSV);
}
void ENC28J60::powerUp() {
writeOp(ENC28J60_BIT_FIELD_CLR, ECON2, ECON2_PWRSV);
while(!readRegByte(ESTAT) & ESTAT_CLKRDY);
writeOp(ENC28J60_BIT_FIELD_SET, ECON1, ECON1_RXEN);
}
void ENC28J60::enableBroadcast (bool temporary) {
writeRegByte(ERXFCON, readRegByte(ERXFCON) | ERXFCON_BCEN);
if(!temporary)
broadcast_enabled = true;
}
void ENC28J60::disableBroadcast (bool temporary) {
if(!temporary)
broadcast_enabled = false;
if(!broadcast_enabled)
writeRegByte(ERXFCON, readRegByte(ERXFCON) & ~ERXFCON_BCEN);
}
void ENC28J60::enableMulticast () {
writeRegByte(ERXFCON, readRegByte(ERXFCON) | ERXFCON_MCEN);
}
void ENC28J60::disableMulticast () {
writeRegByte(ERXFCON, readRegByte(ERXFCON) & ~ERXFCON_MCEN);
}
uint8_t ENC28J60::doBIST ( byte csPin) {
#define RANDOM_FILL 0b0000
#define ADDRESS_FILL 0b0100
#define PATTERN_SHIFT 0b1000
#define RANDOM_RACE 0b1100
// init
//if (bitRead(SPCR, SPE) == 0)
// initSPI();
selectPin = csPin;
pinMode(selectPin, OUTPUT);
disableChip();
writeOp(ENC28J60_SOFT_RESET, 0, ENC28J60_SOFT_RESET);
delay(2); // errata B7/2
while (!readOp(ENC28J60_READ_CTRL_REG, ESTAT) & ESTAT_CLKRDY) ;
// now we can start the memory test
uint16_t macResult;
uint16_t bitsResult;
// clear some of the registers registers
writeRegByte(ECON1, 0);
writeReg(EDMAST, 0);
// Set up necessary pointers for the DMA to calculate over the entire memory
writeReg(EDMAND, 0x1FFFu);
writeReg(ERXND, 0x1FFFu);
// Enable Test Mode and do an Address Fill
SetBank(EBSTCON);
writeRegByte(EBSTCON, EBSTCON_TME | EBSTCON_BISTST | ADDRESS_FILL);
// wait for BISTST to be reset, only after that are we actually ready to
// start the test
// this was undocumented :(
while (readOp(ENC28J60_READ_CTRL_REG, EBSTCON) & EBSTCON_BISTST);
writeOp(ENC28J60_BIT_FIELD_CLR, EBSTCON, EBSTCON_TME);
// now start the actual reading an calculating the checksum until the end is
// reached
writeOp(ENC28J60_BIT_FIELD_SET, ECON1, ECON1_DMAST | ECON1_CSUMEN);
SetBank(EDMACS);
while(readOp(ENC28J60_READ_CTRL_REG, ECON1) & ECON1_DMAST);
macResult = readReg(EDMACS);
bitsResult = readReg(EBSTCS);
// Compare the results
// 0xF807 should always be generated in Address fill mode
if ((macResult != bitsResult) || (bitsResult != 0xF807)) {
return 0;
}
// reset test flag
writeOp(ENC28J60_BIT_FIELD_CLR, EBSTCON, EBSTCON_TME);
// Now start the BIST with random data test, and also keep on swapping the
// DMA/BIST memory ports.
writeRegByte(EBSTSD, 0b10101010 | millis());
writeRegByte(EBSTCON, EBSTCON_TME | EBSTCON_PSEL | EBSTCON_BISTST | RANDOM_FILL);
// wait for BISTST to be reset, only after that are we actually ready to
// start the test
// this was undocumented :(
while (readOp(ENC28J60_READ_CTRL_REG, EBSTCON) & EBSTCON_BISTST);
writeOp(ENC28J60_BIT_FIELD_CLR, EBSTCON, EBSTCON_TME);
// now start the actual reading an calculating the checksum until the end is
// reached
writeOp(ENC28J60_BIT_FIELD_SET, ECON1, ECON1_DMAST | ECON1_CSUMEN);
SetBank(EDMACS);
while(readOp(ENC28J60_READ_CTRL_REG, ECON1) & ECON1_DMAST);
macResult = readReg(EDMACS);
bitsResult = readReg(EBSTCS);
// The checksum should be equal
return macResult == bitsResult;
}