Issues
- 0
Can I install the appliance on the back?
#169 opened by NoNoTaiMu - 0
Manual page 8 : it shows the 625 bearings while the trident does not have any.
#167 opened by Nimajine - 0
Manual: X carriage lacks two heat inserts
#165 opened by Icenowy - 1
Line 172 of Kraken config has a typo: sstep_pin: PG11 instead of step_pin: PG11
#163 opened by GreenPlasticWaterCan - 2
Wiring PE to frame does nothing.
#119 opened by cmdremily - 3
Missing STL part in skirt
#162 opened by filamonkey - 1
Why is there no spider motherboard configuration file in the Firmware directory?
#161 opened by tianyi725 - 2
- 1
[Manual] With the popularity of CANbus mods, it could be helpful to document alternate endstop mounting.
#115 opened by BerzerkaDurk - 1
- 0
Double period in RAIL SAFETY
#160 opened by nmattia - 0
Incorrect HAMMERHEAD NUT description
#159 opened by nmattia - 1
Manual: 300mm bed frame spacing.
#133 opened by atoomnetmarc - 1
- 0
Manual: controller board wrong link pg203
#134 opened by atoomnetmarc - 0
Subreddit mentioned on page 287
#140 opened by Gamithon - 0
[Manual] Clarification bolting x-axis to y-rail, and inconsistency in "end stop" terminology
#149 opened by dekay - 5
Thumb bolt/ Knurled nut wrong size in manual?
#120 opened by Faenum - 2
Manual: The Voron Belt Path link
#106 opened by MallocArray - 0
Tip on IGUS chains overlaps image on p261
#103 opened by thunderkeys - 0
Suggestion: page 177 - in what direction to rotate
#152 opened by calmarc - 0
suggestion: page 226 - zip-tie 3d-print not mentioned
#151 opened by calmarc - 2
Issue with extruder. It freezes up when printer is powered and won't work when activated
#154 opened by HeATThER - 0
List of all 3d-parts and their usage?
#153 opened by calmarc - 0
- 1
No puedo hacer funcionar mi impresora me marca error moonraker y no se programar
#147 opened by Rominadesign - 1
Manual text colour hard to read
#135 opened by KodiTheDog - 0
Manual: Jumper remove/install ordering suggestion
#127 opened by MallocArray - 4
- 0
Manual: VHB on panel clips not depicted
#129 opened by cromine11 - 1
Manual: Page 100
#139 opened by webRat - 0
Trident Manuel still has Afterburner parts and instructions in the X Axis section
#132 opened by Deadbob1978 - 0
Typo on Trident Manual Page 4
#138 opened by shaunmorris - 1
Manual: Page 217 does not mention roll-in T-nuts
#121 opened by MallocArray - 1
Manual: Hall Effect Endstop link
#105 opened by MallocArray - 0
Manual: HALL EFFECT ENDSTOP link
#107 opened by MallocArray - 0
Manual: Jumper set 5 mislabeled
#108 opened by MallocArray - 0
Manual: Jumper install mislabled
#109 opened by MallocArray - 1
Manual: Toolhead PCB link does not work
#110 opened by MallocArray - 1
Manual: Page 15 Extrusion misspelled
#111 opened by MallocArray - 1
Sensorless config
#125 opened by cmdtbalbosa - 1
- 1
Trident r1 "power_inlet_filtered" bug/fault
#117 opened by Exerqtor - 1
power_inlet_filtered.stl cad issue?
#112 opened by leesafur - 1
BOM should also include a terminal cover for the 5V PSU
#104 opened by dekay - 1
Manual: Typo on page 15
#113 opened by Tuxedo-VE - 1
Invalid Record Index in assembly step file
#102 opened by Leafy1 - 1
Trident Configurator has wrong Cable Chain amount
#100 opened by ccfman2004 - 0
Manual: Explaination PTFE tube from holder to hotend is missing and when to use which tube.
#99 opened by tkalbitz - 1
Initial Startup Checks: Mixed up X and Y
#98 opened by FlyingT