ERROR: device-tree-xilinx-v2021.1
sarosse opened this issue · 9 comments
Environment (please complete the following information):
- Project to build: ZCU102
- Petalinux version: 2021.1
- HDL branch:2019_r2
- META-ADI branch:master
- Using meta-adi petalinux docker image?No
Describe the bug
Buid device tree fails ,
Screenshots
ERROR: device-tree-xilinx-v2021.1+gitAUTOINC+252758eb1f-r0 do_configure: Execution of '/home/d59006/Petalinux_projects/Project_0_0_0_68/build/tmp/work/zcu102_zynqmp-xilinx-linux/device-tree/xilinx-v2021.1+gitAUTOINC+252758eb1f-r0/temp/run.do_configure.134877' failed with exit code 2:
MISC_ARG is -hdf_type xsa -yamlconf /home/d59006/Petalinux_projects/Project_0_0_0_68/build/tmp/work/zcu102_zynqmp-xilinx-linux/device-tree/xilinx-v2021.1+gitAUTOINC+252758eb1f-r0/device-tree.yaml
APP_ARG is -app "device-tree"
Using xsct from: /home/d59006/petalinux/tools/xsct//bin/xsct
cmd is: xsct -sdx -nodisp /home/d59006/Petalinux_projects/Project_0_0_0_68/build/tmp/work/zcu102_zynqmp-xilinx-linux/device-tree/xilinx-v2021.1+gitAUTOINC+252758eb1f-r0/dtgen.tcl -ws /home/d59006/Petalinux_projects/Project_0_0_0_68/project-spec/configs/../../components/plnx_workspace/device-tree -pname device-tree -rp /home/d59006/Petalinux_projects/Project_0_0_0_68/build/tmp/work/zcu102_zynqmp-xilinx-linux/device-tree/xilinx-v2021.1+gitAUTOINC+252758eb1f-r0/git -processor_ip psu_cortexa53 -hdf /home/d59006/Petalinux_projects/Project_0_0_0_68/build/tmp/deploy/images/zcu102-zynqmp/Xilinx-zcu102-zynqmp.xsa -arch 64 -app "device-tree" -hdf_type xsa -yamlconf /home/d59006/Petalinux_projects/Project_0_0_0_68/build/tmp/work/zcu102_zynqmp-xilinx-linux/device-tree/xilinx-v2021.1+gitAUTOINC+252758eb1f-r0/device-tree.yaml
INFO: [Hsi 55-2053] elapsed time for repository (/home/d59006/petalinux/tools/xsct/data/embeddedsw) loading 0 seconds
hsi::open_hw_design: Time (s): cpu = 00:00:10 ; elapsed = 00:00:08 . Memory (MB): peak = 2168.305 ; gain = 687.211 ; free physical = 13444 ; free virtual = 19143
WARNING: Clock pin "clk" of IP block "axi_adrv9009_rx_clkgen" is not connected to any of the pl_clk"
WARNING: Clock pin "fifo_wr_clk" of IP block "axi_adrv9009_rx_dma" is not connected to any of the pl_clk"
WARNING: Clock pin "core_clk" of IP block "axi_adrv9009_rx_jesd_rx_axi" is not connected to any of the pl_clk"
WARNING: Clock pin "clk" of IP block "axi_adrv9009_rx_os_clkgen" is not connected to any of the pl_clk"
WARNING: Clock pin "fifo_wr_clk" of IP block "axi_adrv9009_rx_os_dma" is not connected to any of the pl_clk"
WARNING: Clock pin "core_clk" of IP block "axi_adrv9009_rx_os_jesd_rx_axi" is not connected to any of the pl_clk"
WARNING: Clock pin "clk" of IP block "axi_adrv9009_tx_clkgen" is not connected to any of the pl_clk"
WARNING: Clock pin "core_clk" of IP block "axi_adrv9009_tx_jesd_tx_axi" is not connected to any of the pl_clk"
WARNING: the label "rx_adrv9009_tpl_core_adc_tpl_core" length is 33 characters which is greater than default 31 characters as per DT SPEC...user need to fix the label
WARNING: Clock pin "link_clk" of IP block "rx_adrv9009_tpl_core_adc_tpl_core" is not connected to any of the pl_clk"
WARNING: the label "rx_os_adrv9009_tpl_core_adc_tpl_core" length is 36 characters which is greater than default 31 characters as per DT SPEC...user need to fix the label
WARNING: Clock pin "link_clk" of IP block "rx_os_adrv9009_tpl_core_adc_tpl_core" is not connected to any of the pl_clk"
WARNING: the label "tx_adrv9009_tpl_core_dac_tpl_core" length is 33 characters which is greater than default 31 characters as per DT SPEC...user need to fix the label
WARNING: Clock pin "link_clk" of IP block "tx_adrv9009_tpl_core_dac_tpl_core" is not connected to any of the pl_clk"
WARNING: quotes to be removed or use 2018.1 version for &sata params param0..param7
WARNING: quotes to be removed or use 2018.1 version for &sata params param0..param7
WARNING: quotes to be removed or use 2018.1 version for &sata params param0..param7
WARNING: quotes to be removed or use 2018.1 version for &sata params param0..param7
WARNING: quotes to be removed or use 2018.1 version for &sata params param0..param7
WARNING: quotes to be removed or use 2018.1 version for &sata params param0..param7
WARNING: quotes to be removed or use 2018.1 version for &sata params param0..param7
WARNING: quotes to be removed or use 2018.1 version for &sata params param0..param7
WARNING: Frequency 33.333333333 used instead of 33.333
WARNING: Frequency 33.333 used instead of 27.00
zocl:false
ext_platform:
WARNING: psu_usb_xhci_0: No reset found
WARNING: label 'usb0' found in existing tree
WARNING: the label "rx_adrv9009_tpl_core_adc_tpl_core" length is 33 characters which is greater than default 31 characters as per DT SPEC...user need to fix the label
WARNING: the label "rx_adrv9009_tpl_core_adc_tpl_core" length is 33 characters which is greater than default 31 characters as per DT SPEC...user need to fix the label
WARNING: the label "rx_os_adrv9009_tpl_core_adc_tpl_core" length is 36 characters which is greater than default 31 characters as per DT SPEC...user need to fix the label
WARNING: the label "rx_os_adrv9009_tpl_core_adc_tpl_core" length is 36 characters which is greater than default 31 characters as per DT SPEC...user need to fix the label
WARNING: the label "tx_adrv9009_tpl_core_dac_tpl_core" length is 33 characters which is greater than default 31 characters as per DT SPEC...user need to fix the label
WARNING: the label "tx_adrv9009_tpl_core_dac_tpl_core" length is 33 characters which is greater than default 31 characters as per DT SPEC...user need to fix the label
hsi::generate_target: Time (s): cpu = 00:00:29 ; elapsed = 00:00:31 . Memory (MB): peak = 2168.305 ; gain = 0.000 ; free physical = 13440 ; free virtual = 19140
/home/d59006/Petalinux_projects/Project_0_0_0_68/build/tmp/work/zcu102_zynqmp-xilinx-linux/device-tree/xilinx-v2021.1+gitAUTOINC+252758eb1f-r0/temp/run.do_configure.134877: 194: [: y: unexpected operator
sed: can't read /home/d59006/Petalinux_projects/Project_0_0_0_68/build/tmp/work/zcu102_zynqmp-xilinx-linux/device-tree/xilinx-v2021.1+gitAUTOINC+252758eb1f-r0/zynqmp-zcu102-revA.dts: No such file or directory
WARNING: exit code 2 from a shell command.
ERROR: Logfile of failure stored in: /home/d59006/Petalinux_projects/Project_0_0_0_68/build/tmp/work/zcu102_zynqmp-xilinx-linux/device-tree/xilinx-v2021.1+gitAUTOINC+252758eb1f-r0/temp/log.do_configure.134877
Hi,
Sorry for the late reply. The master branch is supposed to be used with hdl master and not 2019_r2...
Hi Nunojsa , that was my mistake ... i had used hdl master :
Project to build: ZCU102
Petalinux version: 2021.1
HDL branch:master
META-ADI branch:master
Ubuntu 20.04.4
Using meta-adi petalinux docker image?No
I followed all the procedures described in meta-adi ... I have cleaned the project, I made a new project , anyway I tryed a lots of ways but it always gives me this error ... :(
Ok, I will need a bit more detail on which project are you trying to build? ZCU102 is very generic. Can you point me to the project you are trying to build from this table and I will try it on my end?
sorry for forgetting important details and thank you very much for your quick response
the project is: hdl / projects / adrv9009 / zcu102 /,
and I am using the ADRV9008-2W / PCBZ analog device board on the ZCU102 board
I followed this page to build hdl:
https://wiki.analog.com/resources/fpga/docs/build
then I followed this page to build the project:
https://github.com/analogdevicesinc/meta-adi/tree/master/meta-adi-xilinx
I used: zcu102-rev10-adrv9008-2-jesd204-fsm in the DTB kernel.
adrv9009_zcu102 | zynqmp-zcu102-rev10-adrv9008-2-jesd204-fsm
BR
So, things work for me... What do you see when you do ls -la /bin/sh? I'm suspecting you shell is dash...
I thought I had already changed it ... but you have right !! it gives me dash
ls -al ssh
lrwxrwxrwx 1 root root 4 ott 29 16:50 sh -> dash
... Thank you very much !!!
Ok, closing this issue then
i have got also same error how to change dash to bash.
After changes aslo getting error regarding device-treee.how to reslove this issue
ERROR: device-tree-xilinx-v2021.2+gitAUTOINC+c0acd8f064-r0 do_configure: Error: Could not find "pl-delete-nodes-delete-nodes-zynq-zc706-adv7511-adrv9371.dtsi.dtsi" in "/home/icomm/petalinux_new/ad9371/xilinx-zc706-2021.2/build/tmp/work/zc706-xilinx-linux-gnueabi/device-tree/xilinx-v2021.2+gitAUTOINC+c0acd8f064-r0"
ERROR: device-tree-xilinx-v2021.2+gitAUTOINC+c0acd8f064-r0 do_configure: Execution of '/home/icomm/petalinux_new/ad9371/xilinx-zc706-2021.2/build/tmp/work/zc706-xilinx-linux-gnueabi/device-tree/xilinx-v2021.2+gitAUTOINC+c0acd8f064-r0/temp/run.do_configure.213422' failed with exit code 1:
MISC_ARG is -hdf_type xsa -yamlconf /home/icomm/petalinux_new/ad9371/xilinx-zc706-2021.2/build/tmp/work/zc706-xilinx-linux-gnueabi/device-tree/xilinx-v2021.2+gitAUTOINC+c0acd8f064-r0/device-tree.yaml
APP_ARG is -app "device-tree"
Using xsct from: /home/icomm/petalinux_new/tools/xsct//bin/xsct
cmd is: xsct -sdx -nodisp /home/icomm/petalinux_new/ad9371/xilinx-zc706-2021.2/build/tmp/work/zc706-xilinx-linux-gnueabi/device-tree/xilinx-v2021.2+gitAUTOINC+c0acd8f064-r0/dtgen.tcl -ws /home/icomm/petalinux_new/ad9371/xilinx-zc706-2021.2/project-spec/configs/../../components/plnx_workspace/device-tree -pname device-tree -rp /home/icomm/petalinux_new/ad9371/xilinx-zc706-2021.2/build/tmp/work/zc706-xilinx-linux-gnueabi/device-tree/xilinx-v2021.2+gitAUTOINC+c0acd8f064-r0/git -processor_ip ps7_cortexa9 -hdf /home/icomm/petalinux_new/ad9371/xilinx-zc706-2021.2/build/tmp/deploy/images/zynq-generic/Xilinx-zynq-generic.xsa -arch 32 -app "device-tree" -hdf_type xsa -yamlconf /home/icomm/petalinux_new/ad9371/xilinx-zc706-2021.2/build/tmp/work/zc706-xilinx-linux-gnueabi/device-tree/xilinx-v2021.2+gitAUTOINC+c0acd8f064-r0/device-tree.yaml
INFO: [Hsi 55-2053] elapsed time for repository (/home/icomm/petalinux_new/tools/xsct/data/embeddedsw) loading 0 seconds
zocl:false
ext_platform:
hsi::generate_target: Time (s): cpu = 00:00:04 ; elapsed = 00:00:07 . Memory (MB): peak = 2152.941 ; gain = 3.625 ; free physical = 1240 ; free virtual = 2354
INFO: [Hsi 55-2053] elapsed time for repository (/home/icomm/petalinux_new/tools/xsct/data/embeddedsw) loading 0 seconds
WARNING: /home/icomm/petalinux_new/ad9371/xilinx-zc706-2021.2/build/tmp/work/zc706-xilinx-linux-gnueabi/device-tree/xilinx-v2021.2+gitAUTOINC+c0acd8f064-r0/temp/run.do_configure.213422:293 exit 1 from 'exit 1'
WARNING: Backtrace (BB generated script):
#1: bbfatal, /home/icomm/petalinux_new/ad9371/xilinx-zc706-2021.2/build/tmp/work/zc706-xilinx-linux-gnueabi/device-tree/xilinx-v2021.2+gitAUTOINC+c0acd8f064-r0/temp/run.do_configure.213422, line 293
#2: do_configure, /home/icomm/petalinux_new/ad9371/xilinx-zc706-2021.2/build/tmp/work/zc706-xilinx-linux-gnueabi/device-tree/xilinx-v2021.2+gitAUTOINC+c0acd8f064-r0/temp/run.do_configure.213422, line 200
#3: main, /home/icomm/petalinux_new/ad9371/xilinx-zc706-2021.2/build/tmp/work/zc706-xilinx-linux-gnueabi/device-tree/xilinx-v2021.2+gitAUTOINC+c0acd8f064-r0/temp/run.do_configure.213422, line 297
Backtrace (metadata-relative locations):
#1: bbfatal, /home/icomm/petalinux_new/ad9371/xilinx-zc706-2021.2/components/yocto/layers/core/meta/classes/logging.bbclass, line 60
#2: do_configure, /home/icomm/petalinux_new/ad9371/xilinx-zc706-2021.2/components/yocto/layers/meta-xilinx-tools/classes/xsctbase.bbclass, line 78
ERROR: Logfile of failure stored in: /home/icomm/petalinux_new/ad9371/xilinx-zc706-2021.2/build/tmp/work/zc706-xilinx-linux-gnueabi/device-tree/xilinx-v2021.2+gitAUTOINC+c0acd8f064-r0/temp/log.do_configure.213422
ERROR: Task (/home/icomm/petalinux_new/ad9371/xilinx-zc706-2021.2/components/yocto/layers/meta-xilinx/meta-xilinx-bsp/recipes-bsp/device-tree/device-tree.bb:do_configure) failed with exit code '1'
NOTE: Tasks Summary: Attempted 2864 tasks of which 2757 didn't need to be rerun and 1 failed.
Summary: 1 task failed:
/home/icomm/petalinux_new/ad9371/xilinx-zc706-2021.2/components/yocto/layers/meta-xilinx/meta-xilinx-bsp/recipes-bsp/device-tree/device-tree.bb:do_configure
Summary: There was 1 WARNING message shown.
Summary: There were 4 ERROR messages shown, returning a non-zero exit code.
ERROR: Failed to build project. Check the /home/icomm/petalinux_new/ad9371/xilinx-zc706-2021.2/build/build.log file for more details...