antevens/boatcontrol

Issues

• Look into moving things around to fit Sailor Hat

  #39 opened 3 years ago by antevens
  0

• Add 12V power connector for Sailor Hat

  #38 opened 3 years ago by antevens
  0

• Review all design parts for 24V (up to 32V for charge currents)

  #37 opened 3 years ago by antevens
  0

• Resolve missing EW30_Push_DPDT library on opening Kicad Project

  #36 opened 3 years ago by antevens
  0

• Remove extra .dcm file from boatcontrol repository

  #35 opened 3 years ago by antevens
  0

• Clamp down diodes get disconnected with manual buttons

  #34 opened 3 years ago by antevens
  0

• Change layout for Aux buttons

  #33 opened 3 years ago by antevens
  0

• Find out why the magic smoke left the AC indicator LED

  #24 opened 3 years ago by antevens
  3

• Look into why ON/OFF LEDs for upper/ac bank are reverse

  #32 opened 3 years ago by antevens
  0

• Swap Clock and Data pins for EPROM HAT ID

  #30 opened 3 years ago by antevens
  2

• Determine if reset needs to be pulled low all the time for mcp chips

  #31 opened 3 years ago by antevens
  0

• Add current limiting resistors to buck converters

  #29 opened 3 years ago by antevens
  0

• Change all 10M Ohm resistors for multivibrators

  #28 opened 3 years ago by antevens
  0

• Consider thermal reliefs for bus connections

  #27 opened 3 years ago by antevens
  0

• Increase thermal relief for ground plane ICs and bypass caps

  #26 opened 3 years ago by antevens
  0

• Support up to 230V for polarity indicators

  #25 opened 3 years ago by antevens
  0

• Switch pins 1 and 2 on the Shotky for PSUs

  #23 opened 3 years ago by antevens
  0

• Missing ground connection on 5v rail

  #22 opened 3 years ago by antevens
  0

• Rename 12v circuit to 12-24 input or something like that

  #21 opened 3 years ago by antevens
  0

• Polarity LED overpowered for 24v

  #20 opened 3 years ago by antevens
  0

• Switch CxRx and Cx multivibrator leads

  #19 opened 3 years ago by antevens
  0

• Replace 10M ohm resistor banks with 1M

  #18 opened 3 years ago by antevens
  0

• Move power cluster for Raspberri

  #17 opened 3 years ago by antevens
  0

• Change 102 footprint to small cap

  #16 opened 3 years ago by antevens
  0

• Consider adding 5/12v pins and i2c to addon boards

  #15 opened 4 years ago by antevens
  0

• Consider pouring ground on layers 2/3 for critical areas

  #14 opened 4 years ago by antevens
  0

• Add solder-jumbers to disable channel pairing

  #13 opened 4 years ago by antevens
  0

• Create addon board based on Daniel's design

  #12 opened 4 years ago by antevens
  0

• Fix GPIO paths from Raspberry Pi to RJ45 to have adjacent ground pours for EMI/Signal integrity

  #11 opened 4 years ago by antevens
  0

• Review I2C traces to reduce crosstalk

  #10 opened 4 years ago by antevens
  0

• Investigate max peak to peak voltages for AC in case of 3 phase 240V

  #9 opened 4 years ago by antevens
  0

• Replace large vias with multiple small vias

  #8 opened 4 years ago by antevens
  0

• Fix thermal reliefs on addon board solder jumper

  #4 opened 4 years ago by antevens
  1

• Consider replacing 60A connectors with Wago connectors

  #7 opened 4 years ago by antevens
  0

• Update 2 layer design and add/specify bus bars

  #6 opened 4 years ago by antevens
  0

• Create all AC 230V+ version

  #5 opened 4 years ago by antevens
  0

• Create non-latching relay board design

  #2 opened 4 years ago by antevens
  1

• Move XOR gates into their own boxes in the schematic

  #1 opened 4 years ago by antevens
  0

• Create current monitoring PCB

  #3 opened 4 years ago by antevens
  0