Hot end temperature problem

[haw070553]

Did you test the latest release build?

Yes, and the problem still exists.

Bug Description

All works fine until the hot end temperature is reached and the hot end temperature is reached. As soon as it starts to print, the hot end temperature resets to 0 and the hot end starts to cool down.
If you are quick you can go to tune and reset the tempertaure and then the print continues as normal.

Printer Model

Voxelab Aquila

Model Type

X2

Your Mainboard

Aquila N32

Other Mainboard Type

No response

Add-ons that could be involved

CR TOUCH

ProUI-EX | Extra Features?

Yes

Bed Leveling

BLT - BL Touch Bilinear mesh

Did you include your own configuration files?

• A ZIP file containing your Configuration.h and Configuration_adv.h.

Additional information & file uploads

No response

[Mik-S-UMS]

Sounds like it could be a slicer problem if the heater is being told to turn off.

Try printing one of the test prints on the SDcard to confirm.
You should only need to just start to print the first layer to see if there is any difference.
If this starts printing fine then check your slicer settings.

[haw070553]

Thank you for your suggestion, I will check this out. May I also take the time to thank you and your team for creating and improving this software. It is quicker and looks so good on the printer. Howard.

…

On Sat, 14 Sept 2024, 1:35 am Mik, ***@***.***> wrote: Sounds like it could be a slicer problem if the heater is being told to turn off. Try printing one of the test prints on the SDcard to confirm. You should only need to just start to print the first layer to see if there is any difference. If this starts printing fine then check your slicer settings. — Reply to this email directly, view it on GitHub <#157 (comment)>, or unsubscribe <https://github.com/notifications/unsubscribe-auth/A6F2Q5YKP2DFTIKQKZKPCZ3ZWOADLAVCNFSM6AAAAABOGBHADKVHI2DSMVQWIX3LMV43OSLTON2WKQ3PNVWWK3TUHMZDGNJQG42DCOBZGA> . You are receiving this because you authored the thread.Message ID: ***@***.***>

[haw070553]

Hi Mik, I have looked at the Gcode and you are correct. The problem is in voxelMaker. I have changed my slicer and the problem is no more. Thanks again for your help Howard

…

On Sat, 14 Sept 2024 at 08:18, Howard Watson ***@***.***> wrote: Thank you for your suggestion, I will check this out. May I also take the time to thank you and your team for creating and improving this software. It is quicker and looks so good on the printer. Howard. On Sat, 14 Sept 2024, 1:35 am Mik, ***@***.***> wrote: > Sounds like it could be a slicer problem if the heater is being told to > turn off. > > Try printing one of the test prints on the SDcard to confirm. > You should only need to just start to print the first layer to see if > there is any difference. > If this starts printing fine then check your slicer settings. > > — > Reply to this email directly, view it on GitHub > <#157 (comment)>, > or unsubscribe > <https://github.com/notifications/unsubscribe-auth/A6F2Q5YKP2DFTIKQKZKPCZ3ZWOADLAVCNFSM6AAAAABOGBHADKVHI2DSMVQWIX3LMV43OSLTON2WKQ3PNVWWK3TUHMZDGNJQG42DCOBZGA> > . > You are receiving this because you authored the thread.Message ID: > ***@***.***> >

[classicrocker883]

this was my guess as well, the Gcode being the issue. closing for now

[haw070553]

Ok, thanks. Sent from my phone.

…

On Sat, 14 Sept 2024, 11:29 pm Andrew, ***@***.***> wrote: this was my guess as well, the Gcode being the issue. closing for now — Reply to this email directly, view it on GitHub <#157 (comment)>, or unsubscribe <https://github.com/notifications/unsubscribe-auth/A6F2Q53EAN5TNL4XDSXJ6YLZWS2FPAVCNFSM6AAAAABOGBHADKVHI2DSMVQWIX3LMV43OSLTON2WKQ3PNVWWK3TUHMZDGNJRGE4TKMJUHE> . You are receiving this because you authored the thread.Message ID: ***@***.***>