Calibrating Touchscreen - ArchWiki

[ctrlaltkills]

This article or section is a candidate for merging with Touchscreen.

Notes: please use the second argument of the template to provide more detailed indications. (Discuss in Talk:Calibrating Touchscreen)

To use multiple displays (some of which are touchscreens), you need to tell Xorg the mapping between the touch surface and the screen. This can be done using xinput to set the touchscreen's coordinate transformation matrix.

This is a guide to do that, the old-fashioned way, in cases when xrandr does not know about your separate screens because they have been merged into one (e.g., when using TwinView). Everyone else, please go to Touchscreen to do it the easy way.

You will need to run the xinput command every time you attach the monitor or log in. Or course, you can add the command to your session-autostart. You can also use Udev to automate this.

Using nVidia's TwinView

Get to know your system

Your screen

Using TwinView, X will see all your Screens as one big screen. You can get your total height and width by executing

$ xrandr | grep \* # xrandr uses "*" to identify the screen being used

You should see a line like this:

3600x1230 50.0*

what means, your total width is 3600 and your total height is 1230.

Your touch device

Your next job is to get your device's name. Execute

$ xinput list

and find it by its name. Find the item containing [slave pointer (2)], which is usually your own device name. E.g. if the line can look like this

⎜ ↳ Acer T230H id=24 [slave pointer (2)]

your device name is

Acer T230H

Tip: If your device contains both a stylus and a touch screen and more touch devices, then please pay attention to the name when determining the device.

Execute

$ xinput list-props "Device Name"

and make sure there is a property called

Coordinate Transformation Matrix

(If not, you may probably selected the wrong device, please try another one.)

Touch area

You need to shrink your touch area into a rectangle which is smaller than the total screen. This means, you have to know four values:

• Height of touch area
• Width of touch area
• horizontal offset (x offset) (amount of pixels between the left edge of your total screen and the left edge of your touch area)
• vertical offset (y offset) (amount of pixels between the top edge of your total screen and the top edge of your touch area)

Calculate the Coordinate Transformation Matrix

Now, calculate these as accurate as possible:

• c0 = touch_area_width / total_width
• c2 = touch_area_height / total_height
• c1 = touch_area_x_offset / total_width
• c3 = touch_area_y_offset / total_height

The matrix is

[ c0 0 c1 ]
[ 0 c2 c3 ]
[ 0 0 1 ]

which is represented as a row-by-row array:

c0 0 c1 0 c2 c3 0 0 1

Apply the Matrix

Execute

$ xinput set-prop "Device Name" --type=float "Coordinate Transformation Matrix" c0 0 c1 0 c2 c3 0 0 1

e.g.

$ xinput set-prop "Acer T230H" --type=float "Coordinate Transformation Matrix" 0.533333333 0 0 0 0.87804878 0.12195122 0 0 1

to calibrate your touchscreen device. Now, it should work properly.

Do it automatically via a udev rule

Create a file something like /etc/udev/rules.d/99-acer-touch.rules with contents like this:

/etc/udev/rules.d/99-acer-touch.rules

ENV{ID_VENDOR_ID}=="2149",ENV{ID_MODEL_ID}=="2703",ENV{WL_OUTPUT}="DVI1",ENV{LIBINPUT_CALIBRATION_MATRIX}="1 0 0 0 1 0"

Substitute your own touchscreen's vendor ID, model ID, the xrandr output name, and the calibration matrix that you calculated above. This is based on the assumption that you are using the libinput driver for your touchscreen.

Troubleshooting

If, after following these instructions, multiple clicks occur in different places when you touch the screen, you will need to build the xorg-server package using the ABS, applying this patch before you build the package. (This patch fails on the current xorg source, but the bug is present on at least 1 system.)