FX_IO_ERROR
erFalcon opened this issue · 2 comments
Hello,
I am trying to install FileX + LevelX in an stm32h7 microcontroller using a nor custom driver. I do have in my hardware an AT45DB641 NOR memory.
I am working it as an stand alone and also with fault tolerant enable.
My flash chip does have 4096 blocks of 2048 bytes each. i can write and read on pages of 256 bytes each.
Right now i am being able to format and open the media after doing a full reset of my chip, as i understand, putting everything to 1 (0xFF).
I can run the example that stm32 provide about creating a file etc...
My issue happens the second time i do run the code, but this time without erasing the chip.
I am getting following error from levelx: LX_SYSTEM_INVALID_BLOCK
and from filex: FX_IO_ERROR.
My code is as follows:
nor_custom_driver
#ifndef LX_DIRECT_READ
#ifndef NOR_SECTOR_BUFFER_SIZE
#define NOR_SECTOR_BUFFER_SIZE 512
#endif
static ULONG nor_sector_memory[NOR_SECTOR_BUFFER_SIZE];
#endif
UINT lx_stm32_nor_custom_driver_initialize(LX_NOR_FLASH *nor_flash)
{
UINT ret = LX_SUCCESS;
ULONG total_blocks = 0;
ULONG words_per_block = 0;
/* USER CODE BEGIN Init_Section_0 */
total_blocks = _45DBXX_ACTUALBLOCKS;
words_per_block = _45DBXX_BLOCKBYTES / sizeof(ULONG);
nor_flash->lx_nor_flash_base_address = _45DBXX_STARTADD;
/* USER CODE END Init_Section_0 */
nor_flash->lx_nor_flash_total_blocks = total_blocks;
nor_flash->lx_nor_flash_words_per_block = words_per_block;
/* USER CODE BEGIN Init_Section_1 */
/* USER CODE END Init_Section_1 */
nor_flash->lx_nor_flash_driver_read = lx_nor_driver_read;
nor_flash->lx_nor_flash_driver_write = lx_nor_driver_write;
nor_flash->lx_nor_flash_driver_block_erase = lx_nor_driver_block_erase;
nor_flash->lx_nor_flash_driver_block_erased_verify = lx_nor_driver_block_erased_verify;
#ifndef LX_DIRECT_READ
nor_flash->lx_nor_flash_sector_buffer = nor_sector_memory;
#endif
/* USER CODE BEGIN Init_Section_2 */
/* USER CODE END Init_Section_2 */
return ret;
}
static UINT lx_nor_driver_write(ULONG *flash_address, ULONG *source, ULONG words)
{
UINT ret = LX_SUCCESS;
/* USER CODE BEGIN NOR_DRIVER_WRITE */
uint16_t size = words * sizeof(ULONG); // TRANSFORMAMOS LAS WORDS A BYTES
uint8_t writeBuffer[_45DBXX_BLOCKBYTES];
for (int i = 0; i < size; ++i)
{
writeBuffer[i] = ((uint8_t *)source)[i];
}
uint16_t arrayElement = 0 ;
ULONG *localFlashAddress = flash_address;
while (size > 0)
{
uint32_t chunk_size = (size > _45DBXX_PAGEBYTES) ? _45DBXX_PAGEBYTES : size; // Determine the size of the next chunk
AT45dbxx_WritePage2(&writeBuffer[arrayElement], (uint16_t)chunk_size, (uint32_t)localFlashAddress);
// Update the buffer and address for the next chunk
arrayElement += (chunk_size);
localFlashAddress += chunk_size ;
size -= chunk_size;
}
/* USER CODE END NOR_DRIVER_WRITE */
return ret;
}
static UINT lx_nor_driver_block_erase(ULONG block, ULONG erase_count)
{
UINT ret = LX_SUCCESS;
/* USER CODE BEGIN NOR_DRIVER_BLOCK */
uint32_t at45Block = (block * _45DBXX_BLOCKBYTES) + _45DBXX_STARTADD ;
AT45dbxx_EraseBlock(at45Block);
/* USER CODE END NOR_DRIVER_BLOCK */
return ret;
}
static UINT lx_nor_driver_block_erased_verify(ULONG block)
{
UINT ret = LX_SUCCESS;
/* USER CODE BEGIN NOR_DRIVER_VERIFY */
// Buffer to store the read data
uint8_t readBuffer[_45DBXX_PAGEBYTES];
// Calculate the starting address in bytes
ULONG start_address = block * _45DBXX_BLOCKBYTES + _45DBXX_STARTADD;
// Read and verify the block in chunks
for (ULONG offset = 0; offset < _45DBXX_BLOCKBYTES; offset += _45DBXX_PAGEBYTES)
{
// Calculate the current address within the block
ULONG current_address = start_address + offset;
// Read a chunk of data
AT45dbxx_ReadPage2(readBuffer, _45DBXX_PAGEBYTES, current_address);
// Verify that all bytes in the chunk are 0xFF
for (ULONG i = 0; i < _45DBXX_PAGEBYTES; ++i)
{
if (readBuffer[i] != 0xFF)
{
ret = LX_ERROR; // Block is not fully erased
break;
}
}
// Break out of the loop if an error is detected
if (ret != LX_SUCCESS)
{
break;
}
}
/* USER CODE END NOR_DRIVER_VERIFY */
return ret;
}
UCHAR media_memory[512];
UCHAR media_buffer[512];
ULONG detected_errors;
UCHAR sratch_memory[4096];
/* Define FileX global data structures. */
FX_MEDIA nor_flash_disk;
FX_FILE fx_file;
ULONG fault_tolerant_memory[3072 / sizeof(ULONG)];
and my filex code is:
UINT MX_FileX_Init(VOID)
{
UINT ret = FX_SUCCESS;
/* USER CODE BEGIN MX_FileX_Init */
/* USER CODE END MX_FileX_Init */
/* Initialize FileX. */
fx_system_initialize();
/* USER CODE BEGIN MX_FileX_Init 1*/
/* USER CODE END MX_FileX_Init 1*/
return ret;
}
void MX_FileX_Process()
{
/* USER CODE BEGIN fx_app_thread_entry 0 */
UINT status;
ULONG available_space_pre;
ULONG available_space_post;
ULONG bytes_read;
CHAR read_buffer[32];
CHAR data[] = "This is FileX working on STM32";
uint8_t err = 0 ;
err = 0x80;
do{
err = AT45dbxxx_Dataflash_ReadStatus(&_45DBXX_SPI);
}while(err == 0x80);
AT45dbxx_EraseChip();
status = fx_media_format(&nor_flash_disk,
fx_stm32_levelx_nor_driver, // Driver entry
(VOID*)CUSTOM_DRIVER_ID, // Device info pointer
(UCHAR*)media_memory, // Media buffer pointer
sizeof(media_memory), // Media buffer size
"NOR_FLASH_DISK", // Volume Name
1, // Number of FATs
32, // Directory Entries
0, // Hidden sectors
_45DBXX_ACTUALBLOCKS, // Total sectors
512, // Sector size
1, // Sectors per cluster
1, // Heads
1); // Sectors per track
status = fx_media_open(&nor_flash_disk, "FX_LX_NOR_DISK", fx_stm32_levelx_nor_driver,(VOID*)CUSTOM_DRIVER_ID , media_buffer, sizeof(media_buffer));
status = fx_media_check(&nor_flash_disk, sratch_memory, 4096,
FX_FAT_CHAIN_ERROR |
FX_DIRECTORY_ERROR |
FX_LOST_CLUSTER_ERROR, &detected_errors);
status = fx_fault_tolerant_enable(&nor_flash_disk, fault_tolerant_memory, sizeof(fault_tolerant_memory));
if (status != FX_SUCCESS)
{
Error_Handler();
}
status = fx_media_space_available(&nor_flash_disk, &available_space_pre);
/* Check the get available state request status. */
if (status != FX_SUCCESS)
{
Error_Handler();
}
status = fx_file_create(&nor_flash_disk, "STM32.TXT");
/* Check the create status. */
if (status != FX_SUCCESS)
{
/* Check for an already created status. This is expected on the
second pass of this loop! */
if (status != FX_ALREADY_CREATED)
{
/* Create error, call error handler. */
Error_Handler();
}
}
status = fx_file_open(&nor_flash_disk, &fx_file, "STM32.TXT", FX_OPEN_FOR_WRITE);
status = fx_file_seek(&fx_file, 0);
status = fx_file_write(&fx_file, data, sizeof(data));
status = fx_file_close(&fx_file);
status = fx_media_flush(&nor_flash_disk);
status = fx_file_open(&nor_flash_disk, &fx_file, "STM32.TXT", FX_OPEN_FOR_READ);
status = fx_file_seek(&fx_file, 0);
status = fx_file_read(&fx_file, read_buffer, sizeof(data), &bytes_read);
status = fx_file_close(&fx_file);
status = fx_media_space_available(&nor_flash_disk, &available_space_post);
status = fx_media_close(&nor_flash_disk);
if (status != FX_SUCCESS)
{
/* Error closing the media, call error handler. */
Error_Handler();
}
while(1)
{
// BSP_LED_Toggle(LED_GREEN);
// tx_thread_sleep(40);
}
}
I really dont understand what is happening, i am even doing a direct read with my memory functions and i am seeing that the text and file name is present in the memory... is this something someone can help me with?
Hello,
This sounds similar to the problem I have. Though I am not using FileX + LevelX in standalone, but with ThreadX. To describe it shortly: I can use the media (NOR Flash over SPI) without any problems if I have written files or have it formatted in the same session. But when I restart the microcontroller (STMH5), it can read the file names of previously created files, but fails in reading their properties. The file handle then either has 0 or max value for each variable. This means that I can "open" files, but cannot read them if they have been created before a shutdown.
Similarly, at the beginning the same kind of problem appeared with opening the media, though that kind of disappeared after formatting it 10 or so times.
Not sure if this is the same problem, but have you checked what your file or media handles look like when/after your opening them?
Hello,
This sounds similar to the problem I have. Though I am not using FileX + LevelX in standalone, but with ThreadX. To describe it shortly: I can use the media (NOR Flash over SPI) without any problems if I have written files or have it formatted in the same session. But when I restart the microcontroller (STMH5), it can read the file names of previously created files, but fails in reading their properties. The file handle then either has 0 or max value for each variable. This means that I can "open" files, but cannot read them if they have been created before a shutdown. Similarly, at the beginning the same kind of problem appeared with opening the media, though that kind of disappeared after formatting it 10 or so times.
Not sure if this is the same problem, but have you checked what your file or media handles look like when/after your opening them?
Hello @m1ndbr34ker
I have been discussing this topic in the following:
STMicroelectronics/x-cube-azrtos-h7#35
still not figured what is going on that prevent me to have this done in the SPI flash. If you can add your thoughs there, maybe we can reach a solution :)
Greetings