SD NAND XTSD01G (surface mounted chip) not formating

[fepalmytho]

Hi Greiman,
First of all, thanks a million for all the work you've done on this topic.
I come back to you as i face a "tiny "problem with a project i've made (based on ESP32-S3).
It used to work with an SD card, where i read and write datas.(big datas, so SPIFFS was not enough in case you ask).
I wanted to avoid SD cards for vibrating/mecanic reliability, so i ended using this SD NAND (1Gbit):
https://www.lcsc.com/product-detail/NAND-FLASH_XTX-XTSD01GLGEAG_C558837.html
So it's a surface mounted chip that acts as an SD card, soldered in my PCB (you for sure know this, but i specify it for other readers).
I send data to the SD nand via a FTP server (as i can't plug it directly to the computer as an usual SD card).
It works fine, but time to time, the SD fails (specially when i "stress" it, like asking readings frequently).
I've tried different settings, like changing the frequency, or delaying readings, but still, the SD crashes and is then "unmounted".
Even if in the code i try to mount it again (Sd.begin), i can't. I need to reset the ESP32, so unpower the SD nand, to make it work again.
I've been investigating for days without finding a solution, and i decided to come bakc to basics:
How this SD nand is formatted? What if this SD is corrupted?
So i decided to format it properly and landed on your post.

I've managed to make it (the code) work, but i think there is something wrong:

1/ The outcome is always "dataAfterErase: ones":
(after check with my FTP server, i can see that files still exist).

init time: 176 ms

Card type: SD2
sdSpecVer: 2.00
HighSpeedMode: true

Manufacturer ID: 0XB
OEM ID: XT
Product: XTSDA
Revision: 1.1
Serial number: 0X26EE1E58
Manufacturing date: 9/2023

cardSize: 127.93 MB (MB = 1,000,000 bytes)
flashEraseSize: 128 blocks
eraseSingleBlock: true
dataAfterErase: ones

OCR: 0X80FF8000

SD Partition Table
part,boot,bgnCHS[3],type,endCHS[3],start,length
1,0X80,0X1,0X1,0X0,0X6,0XFE,0XFF,0XFF,234,248342
2,0X0,0X0,0X0,0X0,0X0,0X0,0X0,0X0,0,0
3,0X0,0X0,0X0,0X0,0X0,0X0,0X0,0X0,0,0
4,0X0,0X0,0X0,0X0,0X0,0X0,0X0,0X0,0,0

Scanning FAT, please wait.

Volume is FAT16
sectorsPerCluster: 4
fatStartSector: 250
dataStartSector: 768
clusterCount: 61952
freeClusterCount: 61615

type any character to start

2/ And also, when i launch serial monitor again, i get (initialization failed):
So i need to unplg/plug it again to come back to first behaviour above).
And that makes me believe that when i "stress" the SD NAND, or something goes wrong, it crashes and is unable to mount again.

SdFat version: 2.2.0

Assuming the SD is the only SPI device.
Edit DISABLE_CS_PIN to disable an SPI device.

Assuming the SD chip select pin is: 10
Edit SD_CS_PIN to change the SD chip select pin.
Done

type any character to start

SD initialization failed.
Do not reformat the card!
Is the card correctly inserted?
Is there a wiring/soldering problem?
Is SD_CS_PIN set to the correct value?
Does another SPI device need to be disabled?
SD errorCode: SD_CARD_ERROR_CMD8 = 0x6
SD errorData = 0x20

type any character to start

What do you think i should do to make it reliable?
Thanks a million for your time and precious skills!
Frederic.

[greiman]

What do you think i should do to make it reliable?

I have no idea. I can't even guess what's happening.