Can not add SES303

Question

Can not add SES303

Closed this issue 3 years ago · 22 comments

My SES303 used to work, but stopped doing so some time ago. I removed the device and tried to add it again but that fails with the following error:
status.missing_multiChannelNodeId_1_on_node
Let me know if I can do something to help sort out this issue!

Answer 1 · 2021-04-10T20:45:19.000Z

Are using the latest version? This issue should have been resolved in v0.5.4

…

On 10 Apr 2021, 22:44 +0200, Arvid Rosen ***@***.***>, wrote: My SES303 used to work, but stopped doing so some time ago. I removed the device and tried to add it again but that fails with the following error: status.missing_multiChannelNodeId_1_on_node Let me know if I can do something to help sort out this issue! — You are receiving this because you are subscribed to this thread. Reply to this email directly, view it on GitHub, or unsubscribe.

Answer 2 · 2021-04-10T20:47:55.000Z

I'll check. Stand by ...

Answer 3 · 2021-04-10T20:48:59.000Z

I'm using v0.5.4

Answer 4 · 2021-04-10T20:51:21.000Z

Ah, sorry, I mixed up the devices. It was ssr303 that was resolved in the latest release.

Let me look into this tomorrow

Answer 5 · 2021-04-10T20:52:03.000Z

Thanks! And please let me know if you need any further information.

Answer 6 · 2021-04-11T12:00:30.000Z

@arvid-r Please try the latest test version (v0.5.5) here: https://homey.app/a/com.horstmann/test/

Answer 7 · 2021-04-11T14:11:12.000Z

Thanks for the update!
I get a new error now:
status.missing_multiChannelNodeId_2_on_node

Answer 8 · 2021-04-11T15:02:23.000Z

@Rocodamelshe are you still able to use your ses303?

Answer 9 · 2021-04-11T15:23:25.000Z

@arvid-r , I made another update to v0.5.6, available as test now.
I'm sorry, since I don't have access to anything but the SRT321 I have not been able to verify (or debug) any other devices, so it is a bit of trial and error.

Answer 10 · 2021-04-11T18:14:03.000Z

The SES303 is working like it should. The attached multichannel device is not updating any temperature for now. Gonna try a re-add and let u know.

Answer 11 · 2021-04-11T18:14:03.000Z

Still:
status.missing_multiChannelNodeId_2_on_node

Answer 12 · 2021-04-11T18:17:29.000Z

Hmm, this is odd. I’ll try some more...

Answer 13 · 2021-04-11T18:28:26.000Z

Removed the SES303 on version 0.5.6 and added it again. Then i get this:

Answer 14 · 2021-04-11T18:33:11.000Z

Ok, so at least there is some consistency between your setups.

I found this in the SES302/303 manual:

"Up to a maximum of five end points supported. The number of end points on the product is detected based on the number of external sensors connected to the product at the time of Inclusion. If external sensor not connected this command class is not supported. Note: external digital sensors must have correct hardware address otherwise it will not work."

I'm guessing @arvid-r doesn't have any external sensors connected and @Rocodamelshe has one connected?

Answer 15 · 2021-04-11T18:33:55.000Z

Correct for my part yes.
Sensor is set to 1 with the switch.

Answer 16 · 2021-04-11T18:36:01.000Z

I guess I need to figure out how the configuration works "If external sensor not connected this command class is not supported.", and dynamically add the command class.

Answer 17 · 2021-04-11T19:57:15.000Z

I have no sensor connected.

Answer 18 · 2021-04-11T21:34:21.000Z

Let's try v0.5.7 in test now :)

Answer 19 · 2021-04-12T04:47:03.000Z

Devices are added! Will let u know tonight if the sensor updates it’s values.

Answer 20 · 2021-04-12T05:04:45.000Z

v0.5.7 works with my setup! Well done

Answer 21 · 2021-04-12T14:42:32.000Z

Works like a charm, cheers m8!

Answer 22 · 2021-04-12T17:00:15.000Z

You are trying to get me drunk @Rocodamelshe!

Thanks!