Some Optimizations
Closed this issue · 1 comments
PenthouseLA commented
i have some more modes as you support currently, can you add these?
Mode: MildDry
Please add a funktion to change SwingH & SwingV in Thermostat Card
and all “default_*_mode” are not working they are always off only celsius and hvac_model are working any ideas?
Its only working when i send a command like this: http://192.168.178.50/cm?cmnd=IRhvac{"Vendor":"PANASONIC_AC","Model":1,"Mode":"Cool","Power":"On","Celsius":"On","Temp":24,"FanSpeed":"Low","SwingV":"Highest","SwingH":"RightMax","Quiet":"Off","Turbo":"On","Econo":"On","Light":"Off","Filter":"Off","Clean":"Off","Beep":"Off","Sleep":-1}
`
#Büro
- platform: tasmota_irhvac
name: "Klimaanlage Buero"
command_topic: "cmnd/Klimaanlage_Buero_5A7A65/irhvac"
# Pick one of the following:
# State is updated when the tasmota device receives an IR signal (includes own transmission and original remote)
# useful when a normal remote is in use alongside the tasmota device, may be less reliable than the second option.
state_topic: "tele/Klimaanlage_Buero_5A7A65/RESULT"
# State is updated when the tasmota device completes IR transmissionm, should be pretty reliable.
#state_topic: "stat/your_tasmota_device/RESULT"
# Uncomment if your 'available topic' of Tasmota IR device are different (if device in HA is disabled)
#availability_topic: "tele/your_tasmota_device/LWT"
temperature_sensor: sensor.wohnzimmer_temperatursensor_snzb_02_temperature
humidity_sensor: sensor.wohnzimmer_temperatursensor_snzb_02_humidity #optional - default None
#power_sensor: binaly_sensor.kitchen_ac_power #optional - default None
vendor: "PANASONIC_AC"
min_temp: 16 #optional - default 16 int value
max_temp: 30 #optional - default 32 int value
target_temp: 26 #optional - default 26 int value
initial_operation_mode: "off" # optional - default "off" string value (one of the "supported_modes")
away_temp: 24 #optional - default 24 int value
precision: 1 #optional - default 1 int or float value. Can be set to 1, 0.5 or 0.1
supported_modes:
- "auto"
- "heat"
- "cool"
- "dry"
- "fan_only" # Use "fan_only" even if Tasmota shows "Mode":"Fan"
- "off" #Turns the AC off - Should be in quotes
# Some devices have "auto" and "fan_only" switched. If the following two lines are uncommented, "auto" and "fan" shoud be commented out
#- "auto_fan_only" #if remote shows fan but tasmota says auto
#- "fan_only_auto" #if remote shows auto but tasmota says fan
supported_fan_speeds:
# Some devices say max,but it is high, and auto which is max. If you uncomment the following two, you have to comment high and max
# - "auto_max" #woud become max
# - "max_high" #would become high
#- "on"
#- "off"
- "auto"
- "min"
- "low"
- "medium"
- "high"
- "max"
supported_swing_list:
#- "off"
- "vertical" #up to down
- "horizontal" # Left to right
#- "both"
default_quiet_mode: "Off" #Quiet und Turbo sind in der Firmware vertauscht | optional - default "Off" string value
default_turbo_mode: "On" #Quiet und Turbo sind in der Firmware vertauscht | optional - default "Off" string value
default_econo_mode: "On" #optional - default "Off" string value
hvac_model: "2" #optional - default "1" string value
celsius_mode: "On" #optional - default "On" string value
default_light_mode: "Off" #optional - default "Off" string value
default_filter_mode: "Off" #optional - default "Off" string value
default_clean_mode: "Off" #optional - default "Off" string value
default_beep_mode: "Off" #optional - default "Off" string value
default_sleep_mode: "-1" #optional - default "-1" string value
default_swingv: "high" #optional - default "" string value
default_swingh: "left" #optional - default "" string value
keep_mode_when_off: True #optional - default False boolean value : Must be True for MITSUBISHI_AC, ECOCLIM, etc.
`
duczz commented
@hristo-atanasov Vertical and horizontal control (middle, right, high etc.) in the lovelance ui would be nice