Some MessageId 's are wrong

[lucwuyts]

In your enum for the MessageId you have to skip some id's

I changed it like this:
enum OpenThermMessageID { Status, // flag8 / flag8 Master and Slave Status flags. TSet, // f8.8 Control setpoint ie CH water temperature setpoint (�C) MConfigMMemberIDcode, // flag8 / u8 Master Configuration Flags / Master MemberID Code SConfigSMemberIDcode, // flag8 / u8 Slave Configuration Flags / Slave MemberID Code Command, // u8 / u8 Remote Command ASFflags, // / OEM-fault-code flag8 / u8 Application-specific fault flags and OEM fault code RBPflags, // flag8 / flag8 Remote boiler parameter transfer-enable & read/write flags CoolingControl, // f8.8 Cooling control signal (%) TsetCH2, // f8.8 Control setpoint for 2e CH circuit (�C) TrOverride, // f8.8 Remote override room setpoint TSP, // u8 / u8 Number of Transparent-Slave-Parameters supported by slave TSPindexTSPvalue, // u8 / u8 Index number / Value of referred-to transparent slave parameter. FHBsize, // u8 / u8 Size of Fault-History-Buffer supported by slave FHBindexFHBvalue, // u8 / u8 Index number / Value of referred-to fault-history buffer entry. MaxRelModLevelSetting, // f8.8 Maximum relative modulation level setting (%) MaxCapacityMinModLevel, // u8 / u8 Maximum boiler capacity (kW) / Minimum boiler modulation level(%) TrSet, // f8.8 Room Setpoint (�C) RelModLevel, // f8.8 Relative Modulation Level (%) CHPressure, // f8.8 Water pressure in CH circuit (bar) DHWFlowRate, // f8.8 Water flow rate in DHW circuit. (litres/minute) DayTime, // special / u8 Day of Week and Time of Day Date, // u8 / u8 Calendar date Year, // u16 Calendar year TrSetCH2, // f8.8 Room Setpoint for 2nd CH circuit (�C) Tr, // f8.8 Room temperature (�C) Tboiler, // f8.8 Boiler flow water temperature (�C) Tdhw, // f8.8 DHW temperature (�C) Toutside, // f8.8 Outside temperature (�C) Tret, // f8.8 Return water temperature (�C) Tstorage, // f8.8 Solar storage temperature (�C) Tcollector, // f8.8 Solar collector temperature (�C) TflowCH2, // f8.8 Flow water temperature CH2 circuit (�C) Tdhw2, // f8.8 Domestic hot water temperature 2 (�C) Texhaust, // s16 Boiler exhaust temperature (�C) TdhwSetUBTdhwSetLB = 48, // s8 / s8 DHW setpoint upper & lower bounds for adjustment (�C) MaxTSetUBMaxTSetLB, // s8 / s8 Max CH water setpoint upper & lower bounds for adjustment (�C) HcratioUBHcratioLB, // s8 / s8 OTC heat curve ratio upper & lower bounds for adjustment TdhwSet = 56, // f8.8 DHW setpoint (�C) (Remote parameter 1) MaxTSet, // f8.8 Max CH water setpoint (�C) (Remote parameters 2) Hcratio, // f8.8 OTC heat curve ratio (�C) (Remote parameter 3) RemoteOverrideFunction=100, // flag8 / - Function of manual and program changes in master and remote room setpoint. OEMDiagnosticCode = 115, // u16 OEM-specific diagnostic/service code BurnerStarts, // u16 Number of starts burner CHPumpStarts, // u16 Number of starts CH pump DHWPumpValveStarts, // u16 Number of starts DHW pump/valve DHWBurnerStarts, // u16 Number of starts burner during DHW mode BurnerOperationHours, // u16 Number of hours that burner is in operation (i.e. flame on) CHPumpOperationHours, // u16 Number of hours that CH pump has been running DHWPumpValveOperationHours, // u16 Number of hours that DHW pump has been running or DHW valve has been opened DHWBurnerOperationHours, // u16 Number of hours that burner is in operation during DHW mode OpenThermVersionMaster, // f8.8 The implemented version of the OpenTherm Protocol Specification in the master. OpenThermVersionSlave, // f8.8 The implemented version of the OpenTherm Protocol Specification in the slave. MasterVersion, // u8 / u8 Master product version number and type SlaveVersion, // u8 / u8 Slave product version number and type };

[ihormelnyk]

Thanks @lucwuyts ,
I'll update library

[ihormelnyk]

Fixed in 1.0.1 version