EthernetWebServer_STM32 build broken on STM32F103C8T6
dm5xx opened this issue · 2 comments
Describe the bug
Its impossible to build because of build is broken. Build log is full of errors like
.pio\libdeps\STM32\STM32Ethernet\src\utility\ethernetif.cpp:80:15: error: 'ETH_DMADescTypeDef' does not name a type
80 | __ALIGN_BEGIN ETH_DMADescTypeDef DMARxDscrTab[ETH_RXBUFNB] __ALIGN_END;/* Ethernet Rx MA Descriptor /
| ^~~~~~~~~~~~~~~~~~
.pio\libdeps\STM32\STM32Ethernet\src\utility\ethernetif.cpp:85:15: error: 'ETH_DMADescTypeDef' does not name a type
85 | __ALIGN_BEGIN ETH_DMADescTypeDef DMATxDscrTab[ETH_TXBUFNB] __ALIGN_END;/ Ethernet Tx DMA Descriptor */
Looking into ehternetif.cpp => Its almost completly red
Steps to Reproduce
Set up Visual Code as described, use this ini and build.
[platformio]
default_envs = STM32
[env]
upload_speed = 921600
lib_compat_mode = strict
lib_ldf_mode = chain+
;lib_ldf_mode = deep+
lib_deps =
stm32duino/STM32duino LwIP@~2.1.2
stm32duino/STM32Ethernet@~1.3.0
khoih-prog/Functional-Vlpp@~1.0.2
khoih-prog/Ethernet_Generic@~2.2.0
uipethernet/UIPEthernet@~2.0.11
jandrassy/EthernetENC@~2.0.2
[env:STM32]
platform = ststm32
framework = arduino
board = bluepill_f103c8
Expected behavior
Build should be possible and all is running fine again :)
Actual behavior
Its dead jim.
Debug and AT-command log (if applicable)
Compiling .pio\build\STM32\lib3c6\STM32Ethernet\utility\stm32_eth.cpp.o
.pio\libdeps\STM32\STM32Ethernet\src\utility\ethernetif.cpp:80:15: error: 'ETH_DMADescTypeDef' does not name a type
80 | __ALIGN_BEGIN ETH_DMADescTypeDef DMARxDscrTab[ETH_RXBUFNB] __ALIGN_END;/* Ethernet Rx MA Descriptor /
| ^~~~~~~~~~~~~~~~~~
.pio\libdeps\STM32\STM32Ethernet\src\utility\ethernetif.cpp:85:15: error: 'ETH_DMADescTypeDef' does not name a type
85 | __ALIGN_BEGIN ETH_DMADescTypeDef DMATxDscrTab[ETH_TXBUFNB] __ALIGN_END;/ Ethernet Tx DMA Descriptor /
| ^~~~~~~~~~~~~~~~~~
In file included from C:\Users\matrixxx.platformio\packages\framework-arduinoststm32\system\STM32F1xx/stm32f1xx_hal_conf.h:13,
from C:\Users\matrixxx.platformio\packages\framework-arduinoststm32\system\Drivers\STM32F1xx_HAL_Driver\Inc/stm32f1xx_hal.h:30,
from C:\Users\matrixxx.platformio\packages\framework-arduinoststm32\system\Drivers\CMSIS\Device\ST\STM32F1xx\Include/stm32f1xx.h:255,
from C:\Users\matrixxx.platformio\packages\framework-arduinoststm32\cores\arduino\stm32/stm32_def.h:28,
from .pio\libdeps\STM32\STM32Ethernet\src\utility\ethernetif.cpp:48:
C:\Users\matrixxx.platformio\packages\framework-arduinoststm32\system\STM32F1xx/stm32f1xx_hal_conf_default.h:187:40: error: 'ETH_MAX_PACKET_SIZE' was not declared in this scope
187 | #define ETH_RX_BUF_SIZE ETH_MAX_PACKET_SIZE / buffer size for receive /
| ^~~~~~~~~~~~~~~~~~~
.pio\libdeps\STM32\STM32Ethernet\src\utility\ethernetif.cpp:90:44: note: in expansion of macro 'ETH_RX_BUF_SIZE'
90 | __ALIGN_BEGIN uint8_t Rx_Buff[ETH_RXBUFNB][ETH_RX_BUF_SIZE] __ALIGN_END; / Ethernet Receive Buffer /
| ^~~~~~~~~~~~~~~
C:\Users\matrixxx.platformio\packages\framework-arduinoststm32\system\STM32F1xx/stm32f1xx_hal_conf_default.h:188:40: error: 'ETH_MAX_PACKET_SIZE' was not declared in this scope
188 | #define ETH_TX_BUF_SIZE ETH_MAX_PACKET_SIZE / buffer size for transmit /
| ^~~~~~~~~~~~~~~~~~~
.pio\libdeps\STM32\STM32Ethernet\src\utility\ethernetif.cpp:95:44: note: in expansion of macro 'ETH_TX_BUF_SIZE'
95 | __ALIGN_BEGIN uint8_t Tx_Buff[ETH_TXBUFNB][ETH_TX_BUF_SIZE] __ALIGN_END; / Ethernet Transmit Buffer */
| ^~~~~~~~~~~~~~~
.pio\libdeps\STM32\STM32Ethernet\src\utility\ethernetif.cpp:97:8: error: 'ETH_HandleTypeDef' does not name a type; did you mean 'RTC_HandleTypeDef'?
97 | static ETH_HandleTypeDef EthHandle;
| ^~~~~~~~~~~~~~~~~
| RTC_HandleTypeDef
.pio\libdeps\STM32\STM32Ethernet\src\utility\ethernetif.cpp:116:22: error: variable or field 'HAL_ETH_MspInit' declared void
116 | void HAL_ETH_MspInit(ETH_HandleTypeDef *heth)
| ^~~~~~~~~~~~~~~~~
.pio\libdeps\STM32\STM32Ethernet\src\utility\ethernetif.cpp:116:22: error: 'ETH_HandleTypeDef' was not declared in this scope; did you mean 'RTC_HandleTypeDef'?
116 | void HAL_ETH_MspInit(ETH_HandleTypeDef *heth)
| ^~~~~~~~~~~~~~~~~
| RTC_HandleTypeDef
.pio\libdeps\STM32\STM32Ethernet\src\utility\ethernetif.cpp:116:41: error: 'heth' was not declared in this scope
116 | void HAL_ETH_MspInit(ETH_HandleTypeDef heth)
| ^~~~
.pio\libdeps\STM32\STM32Ethernet\src\utility\stm32_eth.cpp:67:4: warning: #warning "Default timer used to call ethernet scheduler
at regular interval: TIM14" [-Wcpp]
67 | #warning "Default timer used to call ethernet scheduler at regular interval: TIM14"
| ^~~~~~~
.pio\libdeps\STM32\STM32Ethernet\src\utility\ethernetif.cpp: In function 'void low_level_init(netif)':
.pio\libdeps\STM32\STM32Ethernet\src\utility\ethernetif.cpp:168:3: error: 'EthHandle' was not declared in this scope
168 | EthHandle.Instance = ETH;
| ^~~~~~~~~
.pio\libdeps\STM32\STM32Ethernet\src\utility\ethernetif.cpp:168:24: error: 'ETH' was not declared in this scope
168 | EthHandle.Instance = ETH;
| ^~~
.pio\libdeps\STM32\STM32Ethernet\src\utility\ethernetif.cpp:170:36: error: 'ETH_AUTONEGOTIATION_ENABLE' was not declared in this scope
170 | EthHandle.Init.AutoNegotiation = ETH_AUTONEGOTIATION_ENABLE;
| ^~~~~~~~~~~~~~~~~~~~~~~~~~
.pio\libdeps\STM32\STM32Ethernet\src\utility\ethernetif.cpp:171:26: error: 'ETH_SPEED_100M' was not declared in this scope
171 | EthHandle.Init.Speed = ETH_SPEED_100M;
| ^~~~~~~~~~~~~~
.pio\libdeps\STM32\STM32Ethernet\src\utility\ethernetif.cpp:172:31: error: 'ETH_MODE_FULLDUPLEX' was not declared in this scope
172 | EthHandle.Init.DuplexMode = ETH_MODE_FULLDUPLEX;
| ^~~~~~~~~~~~~~~~~~~
.pio\libdeps\STM32\STM32Ethernet\src\utility\ethernetif.cpp:174:35: error: 'ETH_MEDIA_INTERFACE_RMII' was not declared in this scope
174 | EthHandle.Init.MediaInterface = ETH_MEDIA_INTERFACE_RMII;
| ^~~~~~~~~~~~~~~~~~~~~~~~
.pio\libdeps\STM32\STM32Ethernet\src\utility\ethernetif.cpp:181:27: error: 'ETH_RXPOLLING_MODE' was not declared in this scope
181 | EthHandle.Init.RxMode = ETH_RXPOLLING_MODE;
| ^~~~~~~~~~~~~~~~~~
.pio\libdeps\STM32\STM32Ethernet\src\utility\ethernetif.cpp:183:33: error: 'ETH_CHECKSUM_BY_HARDWARE' was not declared in this scope; did you mean 'CHECKSUM_BY_HARDWARE'?
183 | EthHandle.Init.ChecksumMode = ETH_CHECKSUM_BY_HARDWARE;
| ^~~~~~~~~~~~~~~~~~~~~~~~
| CHECKSUM_BY_HARDWARE
.pio\libdeps\STM32\STM32Ethernet\src\utility\ethernetif.cpp:184:31: error: 'LAN8742A_PHY_ADDRESS' was not declared in this scope
184 | EthHandle.Init.PhyAddress = LAN8742A_PHY_ADDRESS;
| ^~~~~~~~~~~~~~~~~~~~
.pio\libdeps\STM32\STM32Ethernet\src\utility\ethernetif.cpp:187:7: error: 'HAL_ETH_Init' was not declared in this scope; did you mean 'HAL_RTC_Init'?
187 | if (HAL_ETH_Init(&EthHandle) == HAL_OK) {
| ^~~~~~~~~~~~
| HAL_RTC_Init
.pio\libdeps\STM32\STM32Ethernet\src\utility\ethernetif.cpp:193:41: error: 'DMATxDscrTab' was not declared in this scope
Compiling .pio\build\STM32\src\main.cpp.o
193 | HAL_ETH_DMATxDescListInit(&EthHandle, DMATxDscrTab, &Tx_Buff[0][0], ETH_TXBUFNB);
| ^~~~~Compiling .pio\build\STM32\libc4e\STM32duino LwIP\api\api_lib.c.o
.pio\libdeps\STM32\STM32Ethernet\src\utility\ethernetif.cpp:193:56: error: 'Tx_Buff' was not declared in this scope
193 | HAL_ETH_DMATxDescListInit(&EthHandle, DMATxDscrTab, &Tx_Buff[0][0], ETH_TXBUFNB);
| ^~~~~~~
.pio\libdeps\STM32\STM32Ethernet\src\utility\ethernetif.cpp:193:3: error: 'HAL_ETH_DMATxDescListInit' was not declared in this scope
193 | HAL_ETH_DMATxDescListInit(&EthHandle, DMATxDscrTab, &Tx_Buff[0][0], ETH_TXBUFNB);
| ^~~~~~~~~~~~~~~~~~~~~~~~~
.pio\libdeps\STM32\STM32Ethernet\src\utility\ethernetif.cpp:196:41: error: 'DMARxDscrTab' was not declared in this scope
196 | HAL_ETH_DMARxDescListInit(&EthHandle, DMARxDscrTab, &Rx_Buff[0][0], ETH_RXBUFNB);
| ^~~~~~~~~~~~
.pio\libdeps\STM32\STM32Ethernet\src\utility\ethernetif.cpp:196:56: error: 'Rx_Buff' was not declared in this scope
196 | HAL_ETH_DMARxDescListInit(&EthHandle, DMARxDscrTab, &Rx_Buff[0][0], ETH_RXBUFNB);
| ^~~~~~~
.pio\libdeps\STM32\STM32Ethernet\src\utility\stm32_eth.cpp: In function 'void TIM_scheduler_Config()':
.pio\libdeps\STM32\STM32Ethernet\src\utility\stm32_eth.cpp:66:35: error: 'TIM14' was not declared in this scope; did you mean 'TIM1'?
66 | #define DEFAULT_ETHERNET_TIMER TIM14
| ^~~~~
.pio\libdeps\STM32\STM32Ethernet\src\utility\stm32_eth.cpp:184:30: note: in expansion of macro 'DEFAULT_ETHERNET_TIMER'
184 | EthTim = new HardwareTimer(DEFAULT_ETHERNET_TIMER);
| ^~~~~~~~~~~~~~~~~~~~~~
.pio\libdeps\STM32\STM32Ethernet\src\utility\ethernetif.cpp:196:3: error: 'HAL_ETH_DMARxDescListInit' was not declared in this scope
196 | HAL_ETH_DMARxDescListInit(&EthHandle, DMARxDscrTab, &Rx_Buff[0][0], ETH_RXBUFNB);
| ^~~~~~~~~~~~~~~~~~~~~~~~~
.pio\libdeps\STM32\STM32Ethernet\src\utility\ethernetif.cpp:217:3: error: 'HAL_ETH_Start' was not declared in this scope; did you
mean 'HAL_ADC_Start'?
217 | HAL_ETH_Start(&EthHandle);
| ^~~~~~~~~~~~~
| HAL_ADC_Start
.pio\libdeps\STM32\STM32Ethernet\src\utility\ethernetif.cpp:223:39: error: 'PHY_IMR' was not declared in this scope; did you mean
'PHY_MISR'?
223 | HAL_ETH_ReadPHYRegister(&EthHandle, PHY_IMR, ®value);
| ^~~~~~~
| PHY_MISR
.pio\libdeps\STM32\STM32Ethernet\src\utility\ethernetif.cpp:223:3: error: 'HAL_ETH_ReadPHYRegister' was not declared in this scope 223 | HAL_ETH_ReadPHYRegister(&EthHandle, PHY_IMR, ®value);
| ^~~~~~~~~~~~~~~~~~~~~~~
.pio\libdeps\STM32\STM32Ethernet\src\utility\ethernetif.cpp:225:15: error: 'PHY_ISFR_INT4' was not declared in this scope
225 | regvalue |= PHY_ISFR_INT4;
| ^~~~~~~~~~~~~
.pio\libdeps\STM32\STM32Ethernet\src\utility\ethernetif.cpp:228:3: error: 'HAL_ETH_WritePHYRegister' was not declared in this scope
228 | HAL_ETH_WritePHYRegister(&EthHandle, PHY_IMR, regvalue);
| ^~~~~~~~~~~~~~~~~~~~~~~~
*** [.pio\build\STM32\lib3c6\STM32Ethernet\utility\stm32_eth.cpp.o] Error 1
.pio\libdeps\STM32\STM32Ethernet\src\utility\ethernetif.cpp: In function 'err_t low_level_output(netif*, pbuf*)':
.pio\libdeps\STM32\STM32Ethernet\src\utility\ethernetif.cpp:254:33: error: 'EthHandle' was not declared in this scope
254 | uint8_t *buffer = (uint8_t *)(EthHandle.TxDesc->Buffer1Addr);
| ^~~~~~~~~
.pio\libdeps\STM32\STM32Ethernet\src\utility\ethernetif.cpp:255:8: error: 'ETH_DMADescTypeDef' does not name a type
255 | __IO ETH_DMADescTypeDef *DmaTxDesc;
| ^~~~~~~~~~~~~~~~~~
.pio\libdeps\STM32\STM32Ethernet\src\utility\ethernetif.cpp:263:3: error: 'DmaTxDesc' was not declared in this scope
263 | DmaTxDesc = EthHandle.TxDesc;
| ^~~~~~~~~
.pio\libdeps\STM32\STM32Ethernet\src\utility\ethernetif.cpp:269:30: error: 'ETH_DMATXDESC_OWN' was not declared in this scope
269 | if ((DmaTxDesc->Status & ETH_DMATXDESC_OWN) != (uint32_t)RESET) {
| ^~~~~~~~~~~~~~~~~
In file included from C:\Users\matrixxx\.platformio\packages\framework-arduinoststm32\system\STM32F1xx/stm32f1xx_hal_conf.h:13,
from C:\Users\matrixxx\.platformio\packages\framework-arduinoststm32\system\Drivers\STM32F1xx_HAL_Driver\Inc/stm32f1xx_hal.h:30,
from C:\Users\matrixxx\.platformio\packages\framework-arduinoststm32\system\Drivers\CMSIS\Device\ST\STM32F1xx\Include/stm32f1xx.h:255,
from C:\Users\matrixxx\.platformio\packages\framework-arduinoststm32\cores\arduino\stm32/stm32_def.h:28,
from .pio\libdeps\STM32\STM32Ethernet\src\utility\ethernetif.cpp:48:
C:\Users\matrixxx\.platformio\packages\framework-arduinoststm32\system\STM32F1xx/stm32f1xx_hal_conf_default.h:188:40: error: 'ETH_MAX_PACKET_SIZE' was not declared in this scope
188 | #define ETH_TX_BUF_SIZE ETH_MAX_PACKET_SIZE /* buffer size for transmit */
| ^~~~~~~~~~~~~~~~~~~
.pio\libdeps\STM32\STM32Ethernet\src\utility\ethernetif.cpp:279:47: note: in expansion of macro 'ETH_TX_BUF_SIZE'
279 | while ((byteslefttocopy + bufferoffset) > ETH_TX_BUF_SIZE) {
| ^~~~~~~~~~~~~~~
In file included from src\main.cpp:22:
src\defines.h:64:4: warning: #warning Using W5x00 & Ethernet_Generic lib [-Wcpp]
64 | #warning Using W5x00 & Ethernet_Generic lib
| ^~~~~~~
src\defines.h:89:12: fatal error: SPI.h: No such file or directory
### Information
Visual Code newest.
Verbose mode can be enabled via `-v, --verbose` option
CONFIGURATION: https://docs.platformio.org/page/boards/ststm32/bluepill_f103c8.html
PLATFORM: ST STM32 (15.0.0) > BluePill F103C8
HARDWARE: STM32F103C8T6 72MHz, 20KB RAM, 64KB Flash
DEBUG: Current (stlink) External (blackmagic, cmsis-dap, jlink, stlink)
PACKAGES:
- framework-arduinoststm32 @ 4.20100.211028 (2.1.0)
- framework-cmsis @ 2.50700.210515 (5.7.0)
- toolchain-gccarmnoneeabi @ 1.90201.191206 (9.2.1)
LDF: Library Dependency Finder -> https://bit.ly/configure-pio-ldf
LDF Modes: Finder ~ chain+, Compatibility ~ strict
Found 19 compatible libraries
Scanning dependencies...
Dependency Graph
|-- STM32duino LwIP @ 2.1.2
| |-- STM32Ethernet @ 1.3.0
|-- STM32Ethernet @ 1.3.0
|-- Functional-Vlpp @ 1.0.2
|-- Ethernet_Generic @ 2.2.0
|-- UIPEthernet @ 2.0.12
|-- EthernetENC @ 2.0.3
|-- EthernetWebServer_STM32 @ 1.5.0
| |-- STM32duino LwIP @ 2.1.2
| | |-- STM32Ethernet @ 1.3.0
| |-- STM32Ethernet @ 1.3.0
| |-- Functional-Vlpp @ 1.0.2
| |-- Ethernet_Generic @ 2.2.0
### Additional context
Maybe same problem because of this: https://community.st.com/s/question/0D53W00001RKeRZSA1/stm32f4-hal-eth-broken
Hi Khoih! Thanks for all your hard work! Hope you can help here too :) Mike.
Hi @dm5xx
Thanks for your interest in the library.
I just test compile the example HelloServer on F103C8 and still OK using Arduino IDE.
I suggest you try to use Arduino IDE first. Then move on to PIO when everything is OK.
PIO is still not mature enough for complex use cases, and requires much more knowledge / skills to manually modify the settings.
Post for help in PIO Forum if you still have problem.
I'm closing the issue now, because I just compiled and OK here.
.pio\libdeps\STM32\STM32Ethernet\src\utility\ethernetif.cpp:184:31: error: 'LAN8742A_PHY_ADDRESS' was not declared in this scope
184 | EthHandle.Init.PhyAddress = LAN8742A_PHY_ADDRESS;
Another note is that LAN8742A can be only used for some STM32F7 (Nucleo-144 F767ZI, etc.), , etc. as built-in Ethernet.
Now you can only use W5x00 or ENC28J60 for STM31F1, F4.
STM32F1, F4, etc. can't use LAN8742A yet.
Even support to LAN8720 and STM32F4 recently was broken with new STM32 core v2.3.0. I'm not interested in finding out why and had to drop the support to LAN8720 ;={{
If necessary, use the STM32 core v2.2.0 or STM32 core v2.1.0 for LAN8720
Be sure to use in your code before includion of EthernetWebServer_STM32
#define USE_BUILTIN_ETHERNET false
...
#include <EthernetWebServer_STM32.h>