ESP32 bootloop -- "wifi:create wifi task: failed to create task"
Opened this issue · 16 comments
Hi!
I've tried this on a couple of different ESP32 boards and seem to be getting the same result -- a bootloop. Please be patient; my knowledge of the arduino/esp32 environment is .. limited.
Console messages:
rst:0xc (SW_CPU_RESET),boot:0x13 (SPI_FAST_FLASH_BOOT)
configsip: 0, SPIWP:0xee
clk_drv:0x00,q_drv:0x00,d_drv:0x00,cs0_drv:0x00,hd_drv:0x00,wp_drv:0x00
mode:DIO, clock div:1
load:0x3fff0030,len:1184
load:0x40078000,len:13260
load:0x40080400,len:3028
entry 0x400805e4
no config file
E (10392) wifi:create wifi task: failed to create task
Guru Meditation Error: Core 1 panic'ed (Unhandled debug exception).
Debug exception reason: Stack canary watchpoint triggered (wifi_task)
Core 1 register dump:
PC : 0x40090cd3 PS : 0x00060e36 A0 : 0x800900df A1 : 0x3ffbb260
A2 : 0x3ffc0428 A3 : 0xb33fffff A4 : 0x0000cdcd A5 : 0x00060e23
A6 : 0x00060e23 A7 : 0x0000abab A8 : 0xb33fffff A9 : 0xffffffff
A10 : 0x00000037 A11 : 0x3ffb6af8 A12 : 0x00000037 A13 : 0x00060023
A14 : 0x007c0428 A15 : 0x003fffff SAR : 0x00000004 EXCCAUSE: 0x00000001
EXCVADDR: 0x00000000 LBEG : 0x4008ab09 LEND : 0x4008ab2d LCOUNT : 0x8010e990
Environment:
$ arduino-cli core list
ID Installed Latest Name
esp32:esp32 2.0.11 2.0.11 esp32
I just tried with Arduino IDE 2.2.1 and an "Adafruit ESP32 Feather" and I had no problems.
I do see a bootloop if I have an incompatible board selected, such as if I select "Adafruit ESP32 Version 2". You probably want to verify you can upload an empty sketch before you try loading the dali clock
My aduino compile chain appears to be working -- I'm able to compile and upload a test sketch and it works. Also, this host is being used to handle esphome builds which uses the arduino compiler.
Is there something specific about the Feather which makes it a requirement? I've tested on three different varieties of ESP-WROOM-32 boards.
My aduino compile chain appears to be working -- I'm able to compile and upload a test sketch and it works. Also, this host is being used to handle esphome builds which uses the arduino compiler.
Is there something specific about the Feather which makes it a requirement? I've tested on three different varieties of ESP-WROOM-32 boards.
I don't think so. I have no clue why it doesn't work on your particular board. It does say that it failed to create a task, so it is failing on the following line:
xTaskCreatePinnedToCore(wifi_task, "wifi_task", 3*1024, NULL, 0, NULL, 1);
I would maybe see if it works with that commented out. If so, then maybe comment most of the code in "wifi_task" and see whether that works. Then add code until it crashes.
The fact it says "Stack canary watchpoint triggered" may indicate the stack is too small. You could try increasing "3*1024" to something larger, like "4*1024", then increase it until the problem goes away. Maybe my board does not have that stack size check enabled and I am corrupting memory without realizing it.
OK, let's give that a go.
Yep, that fixed the bootloop. I don't have time to do a proper config and test right now, but it looks like a step forward.
Righteo, interesting. It doesn't crash, but
no config file
Starting access point "ESP32 Dali Clock"
E (10384) wifi:create wifi task: failed to create task
E (10387) wifi:create wifi task: failed to create task
Running AP at ESP32 Dali Clock with IP address 0.0.0.0
Go to http://0.0.0.0 to reconfigure
And no access point is visible. I assume returning an IP of 0.0.0.0 is indicative of something going wrong.
EDIT: Removing the xTaskCreatePinnedToCore() just led to zero debug output, nothing happening.
This took me like 3 evenings of swearing to figure out, but you need to downgrade your esp32 tool chain to the one the code was originally written for. This code works fine for me on esp32 v1.0.6. and Arduino IDE 2.2.1(Latest).
OK, let's give that a go.
Yep, that fixed the bootloop. I don't have time to do a proper config and test right now, but it looks like a step forward.
Can you let me know how much you increased the stack size so I can make the fix in the code?
I too was having the same problem with the boot loop and it was resolved with the following code amendments.
void wifi_start() {
xTaskCreatePinnedToCore(wifi_task, "wifi_task", 4*1024, NULL, 0, NULL, 0);
}
But, the WiFi access point failed to initialize correctly.
rst:0xc (SW_CPU_RESET),boot:0x13 (SPI_FAST_FLASH_BOOT)
configsip: 0, SPIWP:0xee
clk_drv:0x00,q_drv:0x00,d_drv:0x00,cs0_drv:0x00,hd_drv:0x00,wp_drv:0x00
mode:DIO, clock div:1
load:0x3fff0030,len:1344
load:0x40078000,len:13964
load:0x40080400,len:3600
entry 0x400805f0
no config file
Starting access point "ESP32 Dali Clock"
E (24863) wifi:create wifi task: failed to create task
E (24863) wifi:create wifi task: failed to create task
Running AP at ESP32 Dali Clock with IP address 0.0.0.0
Go to http://0.0.0.0 to reconfigure
I got the same pb the AP is not showing but I saw this :
This took me like 3 evenings of swearing to figure out, but you need to downgrade your esp32 tool chain to the one the code was originally written for. This code works fine for me on esp32 v1.0.6. and Arduino IDE 2.2.1(Latest).
and I was wondering how to downgrade Arduino IDE (v2.3.1) esp32 tool chain to the recommended v1.0.6, can someone give me some tips on that task ?
Thank you.
+1 to some instructions on running such a downrev build environment.
Additionally, perhaps the author could build a PAL and NTSC binary image that can be flashed with esptool.py?
perhaps the author could build a PAL and NTSC binary image that can be flashed with esptool.py?
This is an interesting idea. The biggest issue I see with it is that one binary would need to work on all the various development boards. I don't know how realistic that is. It is possible that I would need to have one binary per SoC part number. The other issue would that I would need to provide a listing of boards and what output pin will be active. Since I don't own all boards, I would have to find a way to extract the information from the Arduino IDE itself.
Due to the effort involved, I would likely only offer the binaries to my GitHub sponsors, if it is possible at all. I'll need to investigate.
I might be completely wrong here, but I imagine nearly everyone tackling this sort of project is using the bog-standard ESP-WROOM-32 dev boards that are extremely common and extremely cheap. I know there are hundreds of ESP32 boards out there, but once you rule out the ones with fancy features like displays and battery management and LoRa, there's not much real difference between WROOM modules.
OK, I had a little time so I worked out the 1.0.6 ESP32 toolchain process and wrote it up here: https://gist.github.com/PCOWandre/9ae7cabe39bc2389bf806cbd3c2f5bfc
It compiles and runs without error; I need to rat around for an RCA jack to build a cable to test it and I'll save that for daylight.
EDIT: found a RCA jack in my desk drawer -- it works -- pin on my board is labelled D25.
OK, I had a little time so I worked out the 1.0.6 ESP32 toolchain process and wrote it up here: https://gist.github.com/PCOWandre/9ae7cabe39bc2389bf806cbd3c2f5bfc
It compiles and runs without error; I need to rat around for an RCA jack to build a cable to test it and I'll save that for daylight.
EDIT: found a RCA jack in my desk drawer -- it works -- pin on my board is labelled D25.
Thanks for the guide, I got a compile error despite I did select a board from "ESP32 Arduino (in Sketchbook)"
`In file included from c:\users\david\appdata\local\arduino15\packages\esp32\tools\xtensa-esp32-elf-gcc\esp-2021r2-patch5-8.4.0\xtensa-esp32-elf\include\c++\8.4.0\xtensa-esp32-elf\esp32-psram\no-rtti\bits\gthr.h:151,
from c:\users\david\appdata\local\arduino15\packages\esp32\tools\xtensa-esp32-elf-gcc\esp-2021r2-patch5-8.4.0\xtensa-esp32-elf\include\c++\8.4.0\ext\atomicity.h:35,
from c:\users\david\appdata\local\arduino15\packages\esp32\tools\xtensa-esp32-elf-gcc\esp-2021r2-patch5-8.4.0\xtensa-esp32-elf\include\c++\8.4.0\memory:73,
from C:\Users\david\OneDrive\Documents\Arduino\hardware\espressif\esp32\libraries\FS\src/FS.h:24,
from C:\Users\david\OneDrive\Documents\Arduino\hardware\espressif\esp32\libraries\SPIFFS\src/SPIFFS.h:17,
from C:\Users\david\OneDrive\Documents\Arduino\esp32-dali-clock\esp32-dali-clock\esp32-dali-clock.ino:24:
c:\users\david\appdata\local\arduino15\packages\esp32\tools\xtensa-esp32-elf-gcc\esp-2021r2-patch5-8.4.0\xtensa-esp32-elf\include\c++\8.4.0\xtensa-esp32-elf\esp32-psram\no-rtti\bits\gthr-default.h: In function 'int __gthread_mutex_timedlock(__gthread_mutex_t*, const __gthread_time_t*)':
c:\users\david\appdata\local\arduino15\packages\esp32\tools\xtensa-esp32-elf-gcc\esp-2021r2-patch5-8.4.0\xtensa-esp32-elf\include\c++\8.4.0\xtensa-esp32-elf\esp32-psram\no-rtti\bits\gthr-default.h:781:12: error: 'pthread_mutex_timedlock' was not declared in this scope
return _gthrw(pthread_mutex_timedlock) (__mutex, __abs_timeout);
^~~~~~~~
c:\users\david\appdata\local\arduino15\packages\esp32\tools\xtensa-esp32-elf-gcc\esp-2021r2-patch5-8.4.0\xtensa-esp32-elf\include\c++\8.4.0\xtensa-esp32-elf\esp32-psram\no-rtti\bits\gthr-default.h:781:12: note: suggested alternative: 'pthread_mutex_trylock'
exit status 1
Compilation error: exit status 1`
I finally get it working, using another computer with an older version of the IDE and no problem, the project compile without problem and the wifi is working now on the clock.
Thanks again.