playfultechnology/audio-guestbook

Greeting message loops infinitely.

Opened this issue · 1 comments

AnxiemeMusic commented

I managed to get my phone working and recording great. My issue came when I added in my greeting message. When I pick up the phone now it just plays back the message over and over. Almost like the loop does not realize it has been satisfied.

`/**

  • Audio Guestbook, Copyright (c) 2022 Playful Technology
  • Tested using a Teensy 4.0 with Teensy Audio Shield, although should work
  • with minor modifications on other similar hardware
  • When handset is lifted, a pre-recorded greeting message is played, followed by a tone.
  • Then, recording starts, and continues until the handset is replaced.
  • Playback button allows all messages currently saved on SD card through earpiece
  • Files are saved on SD card as 44.1kHz, 16-bit, mono signed integer RAW audio format
  • --> changed this to WAV recording, DD4WH 2022_07_31
  • --> added MTP support, which enables copying WAV files from the SD card via the USB connection, DD4WH 2022_08_01
  • Frank DD4WH, August 1st 2022
  • for a DBP 611 telephone (closed contact when handheld is lifted) & with recording to WAV file
  • contact for switch button 0 is closed when handheld is lifted
  • GNU GPL v3.0 license

*/

#include <Bounce.h>
#include <Audio.h>
#include <Wire.h>
#include <SPI.h>
#include <SD.h>
#include <TimeLib.h>
#include <MTP_Teensy.h>
#include "play_sd_wav.h" // local copy with fixes

// DEFINES
// Define pins used by Teensy Audio Shield
#define SDCARD_CS_PIN 10
#define SDCARD_MOSI_PIN 7
#define SDCARD_SCK_PIN 14
// And those used for inputs
#define HOOK_PIN 0
#define PLAYBACK_BUTTON_PIN 1

#define noINSTRUMENT_SD_WRITE

// GLOBALS
// Audio initialisation code can be generated using the GUI interface at https://www.pjrc.com/teensy/gui/
// Inputs
AudioSynthWaveform waveform1; // To create the "beep" sfx
AudioInputI2S i2s2; // I2S input from microphone on audio shield
AudioPlaySdWavX playWav1; // Play 44.1kHz 16-bit PCM greeting WAV file
AudioRecordQueue queue1; // Creating an audio buffer in memory before saving to SD
AudioMixer4 mixer; // Allows merging several inputs to same output
AudioOutputI2S i2s1; // I2S interface to Speaker/Line Out on Audio shield
AudioConnection patchCord1(waveform1, 0, mixer, 0); // wave to mixer
AudioConnection patchCord3(playWav1, 0, mixer, 1); // wav file playback mixer
AudioConnection patchCord4(mixer, 0, i2s1, 0); // mixer output to speaker (L)
AudioConnection patchCord6(mixer, 0, i2s1, 1); // mixer output to speaker (R)
AudioConnection patchCord5(i2s2, 0, queue1, 0); // mic input to queue (L)
AudioControlSGTL5000 sgtl5000_1;

// Filename to save audio recording on SD card
char filename[15];
// The file object itself
File frec;

// Use long 40ms debounce time on both switches
Bounce buttonRecord = Bounce(HOOK_PIN, 40);
Bounce buttonPlay = Bounce(PLAYBACK_BUTTON_PIN, 40);

// Keep track of current state of the device
enum Mode {Initialising, Ready, Prompting, Recording, Playing};
Mode mode = Mode::Initialising;

float beep_volume = 0.04f; // not too loud :-)

uint32_t MTPcheckInterval; // default value of device check interval [ms]

// variables for writing to WAV file
unsigned long ChunkSize = 0L;
unsigned long Subchunk1Size = 16;
unsigned int AudioFormat = 1;
unsigned int numChannels = 1;
unsigned long sampleRate = 44100;
unsigned int bitsPerSample = 16;
unsigned long byteRate = sampleRatenumChannels(bitsPerSample/8);// samplerate x channels x (bitspersample / 8)
unsigned int blockAlign = numChannels*bitsPerSample/8;
unsigned long Subchunk2Size = 0L;
unsigned long recByteSaved = 0L;
unsigned long NumSamples = 0L;
byte byte1, byte2, byte3, byte4;

void setup() {

Serial.begin(9600);
while (!Serial && millis() < 5000) {
// wait for serial port to connect.
}
Serial.println("Serial set up correctly");
Serial.printf("Audio block set to %d samples\n",AUDIO_BLOCK_SAMPLES);
print_mode();
// Configure the input pins
pinMode(HOOK_PIN, INPUT_PULLUP);
pinMode(PLAYBACK_BUTTON_PIN, INPUT_PULLUP);

// Audio connections require memory, and the record queue
// uses this memory to buffer incoming audio.
AudioMemory(60);

// Enable the audio shield, select input, and enable output
sgtl5000_1.enable();
// Define which input on the audio shield to use (AUDIO_INPUT_LINEIN / AUDIO_INPUT_MIC)
sgtl5000_1.inputSelect(AUDIO_INPUT_MIC);
//sgtl5000_1.adcHighPassFilterDisable(); //
sgtl5000_1.volume(0.95);

mixer.gain(0, 1.0f);
mixer.gain(1, 1.0f);

// Play a beep to indicate system is online
waveform1.begin(beep_volume, 440, WAVEFORM_SINE);
wait(1000);
waveform1.amplitude(0);
delay(1000);

// Initialize the SD card
SPI.setMOSI(SDCARD_MOSI_PIN);
SPI.setSCK(SDCARD_SCK_PIN);
if (!(SD.begin(SDCARD_CS_PIN)))
{
// stop here if no SD card, but print a message
while (1) {
Serial.println("Unable to access the SD card");
delay(500);
}
}
else Serial.println("SD card correctly initialized");

// mandatory to begin the MTP session.
MTP.begin();

// Add SD Card
// MTP.addFilesystem(SD, "SD Card");
MTP.addFilesystem(SD, "Derrick & Lindsay's Audio guestbook"); // choose a nice name for the SD card volume to appear in your file explorer
Serial.println("Added SD card via MTP");
MTPcheckInterval = MTP.storage()->get_DeltaDeviceCheckTimeMS();

// Value in dB

// sgtl5000_1.micGain(15);
sgtl5000_1.micGain(10); // much lower gain is required for the AOM5024 electret capsule

// Synchronise the Time object used in the program code with the RTC time provider.
// See https://github.com/PaulStoffregen/Time
setSyncProvider(getTeensy3Time);

// Define a callback that will assign the correct datetime for any file system operations
// (i.e. saving a new audio recording onto the SD card)
FsDateTime::setCallback(dateTime);

mode = Mode::Ready; print_mode();
}

void loop() {
// First, read the buttons
buttonRecord.update();
buttonPlay.update();

switch(mode){
case Mode::Ready:
// Falling edge occurs when the handset is lifted --> 611 telephone
if (buttonRecord.fallingEdge()) {
Serial.println("Handset lifted");
mode = Mode::Prompting; print_mode();
}
else if(buttonPlay.fallingEdge()) {
//playAllRecordings();
playLastRecording();
}
break;

case Mode::Prompting:
  // Wait a second for users to put the handset to their ear
  wait(1000);
  // Play the greeting inviting them to record their message
  playWav1.play("greeting.wav");    
  // Wait until the  message has finished playing

// while (playWav1.isPlaying()) {
while (!playWav1.isStopped()) {
// Check whether the handset is replaced
buttonRecord.update();
buttonPlay.update();
// Handset is replaced
if(buttonRecord.risingEdge()) {
playWav1.stop();
mode = Mode::Ready; print_mode();
return;
}
if(buttonPlay.fallingEdge()) {
playWav1.stop();
//playAllRecordings();
playLastRecording();
return;
}

  }
  // Debug message
  Serial.println("Starting Recording");
  // Play the tone sound effect
  waveform1.begin(beep_volume, 440, WAVEFORM_SINE);
  wait(1250);
  waveform1.amplitude(0);
  // Start the recording function
  startRecording();
  break;

case Mode::Recording:
  // Handset is replaced
  if(buttonRecord.risingEdge()){
    // Debug log
    Serial.println("Stopping Recording");
    // Stop recording
    stopRecording();
    // Play audio tone to confirm recording has ended
    end_Beep();
  }
  else {
    continueRecording();
  }
  break;

case Mode::Playing: // to make compiler happy
  break;  

case Mode::Initialising: // to make compiler happy
  break;

}

MTP.loop(); // This is mandatory to be placed in the loop code.
}

void setMTPdeviceChecks(bool nable)
{
if (nable)
{
MTP.storage()->set_DeltaDeviceCheckTimeMS(MTPcheckInterval);
Serial.print("En");
}
else
{
MTP.storage()->set_DeltaDeviceCheckTimeMS((uint32_t) -1);
Serial.print("Dis");
}
Serial.println("abled MTP storage device checks");
}

#if defined(INSTRUMENT_SD_WRITE)
static uint32_t worstSDwrite, printNext;
#endif // defined(INSTRUMENT_SD_WRITE)

void startRecording() {
setMTPdeviceChecks(false); // disable MTP device checks while recording
#if defined(INSTRUMENT_SD_WRITE)
worstSDwrite = 0;
printNext = 0;
#endif // defined(INSTRUMENT_SD_WRITE)
// Find the first available file number
// for (uint8_t i=0; i<9999; i++) { // BUGFIX uint8_t overflows if it reaches 255
for (uint16_t i=0; i<9999; i++) {
// Format the counter as a five-digit number with leading zeroes, followed by file extension
snprintf(filename, 11, " %05d.wav", i);
// Create if does not exist, do not open existing, write, sync after write
if (!SD.exists(filename)) {
break;
}
}
frec = SD.open(filename, FILE_WRITE);
Serial.println("Opened file !");
if(frec) {
Serial.print("Recording to ");
Serial.println(filename);
queue1.begin();
mode = Mode::Recording; print_mode();
recByteSaved = 0L;
}
else {
Serial.println("Couldn't open file to record!");
}
}

void continueRecording() {
#if defined(INSTRUMENT_SD_WRITE)
uint32_t started = micros();
#endif // defined(INSTRUMENT_SD_WRITE)
#define NBLOX 16
// Check if there is data in the queue
if (queue1.available() >= NBLOX) {
byte buffer[NBLOXAUDIO_BLOCK_SAMPLESsizeof(int16_t)];
// Fetch 2 blocks from the audio library and copy
// into a 512 byte buffer. The Arduino SD library
// is most efficient when full 512 byte sector size
// writes are used.
for (int i=0;i<NBLOX;i++)
{
memcpy(buffer+iAUDIO_BLOCK_SAMPLESsizeof(int16_t), queue1.readBuffer(), AUDIO_BLOCK_SAMPLES*sizeof(int16_t));
queue1.freeBuffer();
}
// Write all 512 bytes to the SD card
frec.write(buffer, sizeof buffer);
recByteSaved += sizeof buffer;
}

#if defined(INSTRUMENT_SD_WRITE)
started = micros() - started;
if (started > worstSDwrite)
worstSDwrite = started;

if (millis() >= printNext)
{
Serial.printf("Worst write took %luus\n",worstSDwrite);
worstSDwrite = 0;
printNext = millis()+250;
}
#endif // defined(INSTRUMENT_SD_WRITE)
}

void stopRecording() {
// Stop adding any new data to the queue
queue1.end();
// Flush all existing remaining data from the queue
while (queue1.available() > 0) {
// Save to open file
frec.write((byte*)queue1.readBuffer(), AUDIO_BLOCK_SAMPLESsizeof(int16_t));
queue1.freeBuffer();
recByteSaved += AUDIO_BLOCK_SAMPLESsizeof(int16_t);
}
writeOutHeader();
// Close the file
frec.close();
Serial.println("Closed file");
mode = Mode::Ready; print_mode();
setMTPdeviceChecks(true); // enable MTP device checks, recording is finished
}

void playAllRecordings() {
// Recording files are saved in the root directory
File dir = SD.open("/");

while (true) {
File entry = dir.openNextFile();
if (strstr(entry.name(), "greeting"))
{
entry = dir.openNextFile();
}
if (!entry) {
// no more files
entry.close();
end_Beep();
break;
}
//int8_t len = strlen(entry.name()) - 4;
// if (strstr(strlwr(entry.name() + (len - 4)), ".raw")) {
// if (strstr(strlwr(entry.name() + (len - 4)), ".wav")) {
// the lines above throw a warning, so I replace them with this (which is also easier to read):
if (strstr(entry.name(), ".wav") || strstr(entry.name(), ".WAV")) {
Serial.print("Now playing ");
Serial.println(entry.name());
// Play a short beep before each message
waveform1.amplitude(beep_volume);
wait(750);
waveform1.amplitude(0);
// Play the file
playWav1.play(entry.name());
mode = Mode::Playing; print_mode();
}
entry.close();

// while (playWav1.isPlaying()) { // strangely enough, this works for playRaw, but it does not work properly for playWav
while (!playWav1.isStopped()) { // this works for playWav
buttonPlay.update();
buttonRecord.update();
// Button is pressed again
// if(buttonPlay.risingEdge() || buttonRecord.risingEdge()) { // FIX
if(buttonPlay.fallingEdge() || buttonRecord.risingEdge()) {
playWav1.stop();
mode = Mode::Ready; print_mode();
return;
}
}
}
// All files have been played
mode = Mode::Ready; print_mode();
}

void playLastRecording() {
// Find the first available file number
uint16_t idx = 0;
for (uint16_t i=0; i<9999; i++) {
// Format the counter as a five-digit number with leading zeroes, followed by file extension
snprintf(filename, 11, " %05d.wav", i);
// check, if file with index i exists
if (!SD.exists(filename)) {
idx = i - 1;
break;
}
}
// now play file with index idx == last recorded file
snprintf(filename, 11, " %05d.wav", idx);
Serial.println(filename);
playWav1.play(filename);
mode = Mode::Playing; print_mode();
while (!playWav1.isStopped()) { // this works for playWav
buttonPlay.update();
buttonRecord.update();
// Button is pressed again
// if(buttonPlay.risingEdge() || buttonRecord.risingEdge()) { // FIX
if(buttonPlay.fallingEdge() || buttonRecord.risingEdge()) {
playWav1.stop();
mode = Mode::Ready; print_mode();
return;
}
}
// file has been played
mode = Mode::Ready; print_mode();
end_Beep();
}

// Retrieve the current time from Teensy built-in RTC
time_t getTeensy3Time(){
return Teensy3Clock.get();
}

// Callback to assign timestamps for file system operations
void dateTime(uint16_t* date, uint16_t* time, uint8_t* ms10) {

// Return date using FS_DATE macro to format fields.
*date = FS_DATE(year(), month(), day());

// Return time using FS_TIME macro to format fields.
*time = FS_TIME(hour(), minute(), second());

// Return low time bits in units of 10 ms.
*ms10 = second() & 1 ? 100 : 0;
}

// Non-blocking delay, which pauses execution of main program logic,
// but while still listening for input
void wait(unsigned int milliseconds) {
elapsedMillis msec=0;

while (msec <= milliseconds) {
buttonRecord.update();
buttonPlay.update();
if (buttonRecord.fallingEdge()) Serial.println("Button (pin 0) Press");
if (buttonPlay.fallingEdge()) Serial.println("Button (pin 1) Press");
if (buttonRecord.risingEdge()) Serial.println("Button (pin 0) Release");
if (buttonPlay.risingEdge()) Serial.println("Button (pin 1) Release");
}
}

void writeOutHeader() { // update WAV header with final filesize/datasize

// NumSamples = (recByteSaved8)/bitsPerSample/numChannels;
// Subchunk2Size = NumSamplesnumChannels*bitsPerSample/8; // number of samples x number of channels x number of bytes per sample
Subchunk2Size = recByteSaved - 42; // because we didn't make space for the header to start with! Lose 21 samples...
ChunkSize = Subchunk2Size + 34; // was 36;
frec.seek(0);
frec.write("RIFF");
byte1 = ChunkSize & 0xff;
byte2 = (ChunkSize >> 8) & 0xff;
byte3 = (ChunkSize >> 16) & 0xff;
byte4 = (ChunkSize >> 24) & 0xff;
frec.write(byte1); frec.write(byte2); frec.write(byte3); frec.write(byte4);
frec.write("WAVE");
frec.write("fmt ");
byte1 = Subchunk1Size & 0xff;
byte2 = (Subchunk1Size >> 8) & 0xff;
byte3 = (Subchunk1Size >> 16) & 0xff;
byte4 = (Subchunk1Size >> 24) & 0xff;
frec.write(byte1); frec.write(byte2); frec.write(byte3); frec.write(byte4);
byte1 = AudioFormat & 0xff;
byte2 = (AudioFormat >> 8) & 0xff;
frec.write(byte1); frec.write(byte2);
byte1 = numChannels & 0xff;
byte2 = (numChannels >> 8) & 0xff;
frec.write(byte1); frec.write(byte2);
byte1 = sampleRate & 0xff;
byte2 = (sampleRate >> 8) & 0xff;
byte3 = (sampleRate >> 16) & 0xff;
byte4 = (sampleRate >> 24) & 0xff;
frec.write(byte1); frec.write(byte2); frec.write(byte3); frec.write(byte4);
byte1 = byteRate & 0xff;
byte2 = (byteRate >> 8) & 0xff;
byte3 = (byteRate >> 16) & 0xff;
byte4 = (byteRate >> 24) & 0xff;
frec.write(byte1); frec.write(byte2); frec.write(byte3); frec.write(byte4);
byte1 = blockAlign & 0xff;
byte2 = (blockAlign >> 8) & 0xff;
frec.write(byte1); frec.write(byte2);
byte1 = bitsPerSample & 0xff;
byte2 = (bitsPerSample >> 8) & 0xff;
frec.write(byte1); frec.write(byte2);
frec.write("data");
byte1 = Subchunk2Size & 0xff;
byte2 = (Subchunk2Size >> 8) & 0xff;
byte3 = (Subchunk2Size >> 16) & 0xff;
byte4 = (Subchunk2Size >> 24) & 0xff;
frec.write(byte1); frec.write(byte2); frec.write(byte3); frec.write(byte4);
frec.close();
Serial.println("header written");
Serial.print("Subchunk2: ");
Serial.println(Subchunk2Size);
}

void end_Beep(void) {
waveform1.frequency(523.25);
waveform1.amplitude(beep_volume);
wait(250);
waveform1.amplitude(0);
wait(250);
waveform1.amplitude(beep_volume);
wait(250);
waveform1.amplitude(0);
wait(250);
waveform1.amplitude(beep_volume);
wait(250);
waveform1.amplitude(0);
wait(250);
waveform1.amplitude(beep_volume);
wait(250);
waveform1.amplitude(0);
}

void print_mode(void) { // only for debugging
Serial.print("Mode switched to: ");
// Initialising, Ready, Prompting, Recording, Playing
if(mode == Mode::Ready) Serial.println(" Ready");
else if(mode == Mode::Prompting) Serial.println(" Prompting");
else if(mode == Mode::Recording) Serial.println(" Recording");
else if(mode == Mode::Playing) Serial.println(" Playing");
else if(mode == Mode::Initialising) Serial.println(" Initialising");
else Serial.println(" Undefined");
}`