How to set the antenna to use?
Closed this issue · 2 comments
For the dumpHFDL program I use a SDRdx via SoapySDR on Raspberry Pi 4 that's running the bookworm operating system.
The SoapySDRUtil --probe"driver=sdrplay" result is:
######################################################
Soapy SDR -- the SDR abstraction library
######################################################
Probe device driver=sdrplay
[INFO] devIdx: 0
[INFO] SerNo: [removed]
[INFO] hwVer: 4
[INFO] rspDuoMode: 0
[INFO] tuner: 1
[INFO] rspDuoSampleFreq: 0.000000
-- Device identification
driver=SDRplay
hardware=RSPdx
sdrplay_api_api_version=3.120000
sdrplay_api_hw_version=4
-- Peripheral summary
Channels: 1 Rx, 0 Tx
Timestamps: NO
Other Settings:
* RF Gain Select - RF Gain Select
[key=rfgain_sel, default=4, type=string, options=(0, 1, 2, 3, 4, 5, 6, 7, 8, 9, 10, 11, 12, 13, 14, 15, 16, 17, 18, 19, 20, 21, 22, 23, 24, 25, 26, 27)]
* IQ Correction - IQ Correction Control
[key=iqcorr_ctrl, default=true, type=bool]
* AGC Setpoint - AGC Setpoint (dBfs)
[key=agc_setpoint, default=-30, type=int, range=[-60, 0]]
* BiasT Enable - BiasT Control
[key=biasT_ctrl, default=true, type=bool]
* RfNotch Enable - RF Notch Filter Control
[key=rfnotch_ctrl, default=true, type=bool]
* DabNotch Enable - DAB Notch Filter Control
[key=dabnotch_ctrl, default=true, type=bool]
* HDR Enable - RSPdx HDR Control
[key=hdr_ctrl, default=true, type=bool]
-- RX Channel 0
Full-duplex: NO
Supports AGC: YES
Stream formats: CS16, CF32
Native format: CS16 [full-scale=32767]
Antennas: Antenna A, Antenna B, Antenna C
Corrections: DC removal
Full gain range: [0, 66] dB
IFGR gain range: [20, 59] dB
RFGR gain range: [0, 27] dB
Full freq range: [0.001, 2000] MHz
RF freq range: [0.001, 2000] MHz
CORR freq range: MHz
Sample rates: 0.0625, 0.096, 0.125, 0.192, 0.25, ..., 6, 7, 8, 9, 10 MSps
Filter bandwidths: 0.2, 0.3, 0.6, 1.536, 5, 6, 7, 8 MHz
How can I set the "Antenna C" as the one to be used? I tried all variations I could think of of driver=sdrplay,antenna="Atenna C" but the result is the same:
driver=sdrplay,ant=Antenna C: center frequency set to 3814.000 kHz
driver=sdrplay,ant=Antenna C: frequency correction set to 0.00 ppm
driver=sdrplay,ant=Antenna C: auto gain enabled
driver=sdrplay,ant=Antenna C: using antenna Antenna A
driver=sdrplay,ant=Antenna C: using native sample format CS16 (full_scale: 32767.000)
Thanks in advance!
Isn't the antenna arg antenna and not ant? If you found ant mentioned somewhere that should be corrected.
Just found it by accident. driver=sdrplay --antenna="Antenna C".
Thank you very much for your help!