Sync/Clock Issue

Question

Sync/Clock Issue

E2Xtreme opened this issue 8 months ago · 0 comments

Hello!

I have built GBS Control units in the past but I am having a hell of a time with this one. I cannot get a picture out of it for the life of me. Tested a Saturn and genesis using SCART RetroAccess cables - Image comes on for a second then horizontal tearing and it disappears.
Tested a Dreamcast using VGA and the screen vertically scrolls then disappears
SCART input is a connector I wired in to the white connector behind VGA in
100ohm resistor is added to sync
Using an external clock generator wired in
Using a GBS2HDMI for output
Triad 5v 3a power supply
same results on 2 different monitors.
Issue with the sync somewhere? Potential bad clock generator? Any ideas appreciated! Logs below
Thank you

user command s at settings source 0, custom slot 65, status 0
Source format not properly recognized, using fallback preset!

Scanning inputs for sources ...
user command s at settings source 5, custom slot 65, status 0
Source format not properly recognized, using fallback preset!

Scanning inputs for sources ...
user command s at settings source 2, custom slot 65, status 0
Source format not properly recognized, using fallback preset!

Scanning inputs for sources ...
user command s at settings source 2, custom slot 65, status 0
Source format not properly recognized, using fallback preset!

Scanning inputs for sources ...
user command 4 at settings source 5, custom slot 65, status 0
saving to preset slot A
open save file ok
preset saved as: /preset_unknown.A
user command s at settings source 2, custom slot 65, status 0
Source format not properly recognized, using fallback preset!

Scanning inputs for sources ...
user command s at settings source 5, custom slot 65, status 0
Source format not properly recognized, using fallback preset!

user command s at settings source 5, custom slot 65, status 0
Source format not properly recognized, using fallback preset!

Scanning inputs for sources ...
user command f at settings source 5, custom slot 65, status 0
Source format not properly recognized, using fallback preset!

Scanning inputs for sources ...
user command h at settings source 0, custom slot 65, status 0
Source format not properly recognized, using fallback preset!

Scanning inputs for sources ...
user command L at settings source 1, custom slot 65, status 0
Source format not properly recognized, using fallback preset!

serial command K at settings source 6, custom slot 65, status 0
clock gen reset: 81000000
post preset: rto->videoStandardInput 0 > 0
ADC offset: R:43 G:44 B:3F
clock gen reset: 81000000
pass-through on
user command s at settings source 10, custom slot 65, status 21
Source format not properly recognized, using fallback preset!

Scanning inputs for sources ...
user command s at settings source 5, custom slot 65, status 0
Source format not properly recognized, using fallback preset!

Scanning inputs for sources ...
user command s at settings source 5, custom slot 65, status 0
Source format not properly recognized, using fallback preset!

Scanning inputs for sources ...
user command s at settings source 5, custom slot 65, status 0
Source format not properly recognized, using fallback preset!

Scanning inputs for sources ...
Activity detected, input: RGB

2345678
Format change: 1
ADC offset: R:43 G:44 B:3F
clock gen reset: 108000000
sync skipped sfr wrong: 0.00
sync skipped sfr wrong: 0.00

.sync skipped sfr wrong: 0.00

.
2*
no signal
h: 427 v: 525 PLL:0 A:7b7b7b S:8f.10.10 I:00 D:0000 m:1 ht:2558 vt: 262 hpw: 1 u: 96 s: 0 S:13 W:31

(debug) ign. length: 0x63
(debug) ign. length: 0x6A
user command f at settings source 2, custom slot 65, status 5
ADC offset: R:43 G:44 B:3F
clock gen reset: 162000000
sync skipped sfr wrong: 0.00
user command p at settings source 0, custom slot 65, status 1
matched preset override > 1280x960
ADC offset: R:43 G:44 B:3F
clock gen reset: 162000000
user command p at settings source 4, custom slot 65, status 1
matched preset override > 1280x960
ADC offset: R:43 G:44 B:3F
clock gen reset: 162000000
sync skipped sfr wrong: 0.00

.*****
no signal
h: 427 v: 607 PLL:0 A:7b7b7b S:07.10.10 I:00 D:0008 m:0 ht:2345 vt: 240 hpw: 91 u: 96 s: 0 S:13 W:31

(debug) ign. length: 0x51
(debug) ign. length: 0x64
sync skipped sfr wrong: 0.00
user command s at settings source 4, custom slot 65, status 1
ADC offset: R:43 G:44 B:3F
clock gen reset: 108000000
user command s at settings source 5, custom slot 65, status 5
ADC offset: R:43 G:44 B:3F
clock gen reset: 108000000
user command L at settings source 5, custom slot 65, status 5
ADC offset: R:43 G:44 B:3F
clock gen reset: 40500000
sync skipped sfr wrong:
preset applied: 720x480 for NTSC 60Hz

user command s at settings source 1, custom slot 65, status 4
ADC offset: R:43 G:44 B:3F
clock gen reset: 108000000
sync skipped sfr wrong: 0.00

.* (debug) ign. length: 0x70
***user command p at settings source 5, custom slot 65, status 5
matched preset override > 1280x960
(debug) ign. length: 0x72
ADC offset: R:43 G:44 B:40
clock gen reset: 162000000
sync skipped sfr wrong: 0.00
user command p at settings source 4, custom slot 65, status 1
matched preset override > 1280x960
(debug) ign. length: 0x72
ADC offset: R:43 G:44 B:40
clock gen reset: 162000000
sync skipped sfr wrong: 0.00
user command h at settings source 4, custom slot 65, status 1
(debug) ign. length: 0x72
ADC offset: R:43 G:44 B:40
clock gen reset: 81000000
user command h at settings source 1, custom slot 65, status 4
(debug) ign. length: 0x72
ADC offset: R:43 G:44 B:40
clock gen reset: 81000000
sync skipped sfr wrong: 0.00
user command g at settings source 1, custom slot 65, status 4
(debug) ign. length: 0x6F
ADC offset: R:43 G:44 B:40
clock gen reset: 108000000

preset applied: 1280x720 for NTSC 60Hz

sync skipped sfr wrong: 0.00
user command f at settings source 3, custom slot 65, status 3
(debug) ign. length: 0x72
ADC offset: R:43 G:44 B:40
clock gen reset: 162000000

preset applied: 1280x960 for NTSC 60Hz

sync skipped sfr wrong: 0.00
user command p at settings source 4, custom slot 65, status 1
matched preset override > 1280x960
(debug) ign. length: 0x6F
ADC offset: R:43 G:44 B:40
clock gen reset: 162000000
user command p at settings source 4, custom slot 65, status 1
matched preset override > 1280x960
(debug) ign. length: 0x72
ADC offset: R:43 G:44 B:40
clock gen reset: 162000000
sync skipped sfr wrong: 0.00
user command p at settings source 4, custom slot 65, status 1
matched preset override > 1280x960
(debug) ign. length: 0x72
ADC offset: R:43 G:44 B:40
clock gen reset: 162000000

preset applied: 1280x960 for NTSC 60Hz

sync skipped sfr wrong: 0.00
user command s at settings source 4, custom slot 65, status 1
sync skipped sfr wrong: 0.00
*
Restart

Activity detected, input: RGB
VSync: present
HSync: presentuser command f at settings source 5, custom slot 65, status 22
Source format not properly recognized, using fallback preset!
<reset>
Activity detected, input: RGB
VSync: present
HSync: presentRGB/HV 
clock gen reset: 81000000
user command f at settings source 0, custom slot 65, status 22
Source format not properly recognized, using fallback preset!
<reset>
user command s at settings source 0, custom slot 65, status 0
Source format not properly recognized, using fallback preset!
ADC offset: R:43 G:44 B:3F
clock gen reset: 108000000
 (debug) updateCoastPosition: low res, low hz

preset applied: 1920x1080 for EDTV 60Hz(set your TV aspect ratio to 16:9!)


.*****
no signal
h: 214 v:2027 PLL:0 A:7b7b7b S:02.18.00 H-V- I:82 D:068e m:0 ht:   8 vt:2043 hpw: 185 u: 96 s: 0 S:13 W:31

<reset>
Scanning inputs for sources ...
Activity detected, input: RGB
VSync: present
HSync: presentRGB/HV 
clock gen reset: 81000000
```````````````<reset>
Activity detected, input: RGB
VSync: present
HSync: presentsync skipped sfr wrong: serial command L at settings source 5, custom slot 65, status 5
Output Format: Component
 (debug) ign. length: 0x72
ADC offset: R:43 G:44 B:3F
clock gen reset: 108000000
serial command L at settings source 5, custom slot 65, status 3
 (debug) ign. length: 0x72
ADC offset: R:43 G:44 B:3F
clock gen reset: 108000000
user command v at settings source 5, custom slot 65, status 3
user command 5 at settings source 5, custom slot 65, status 3
FTL off
user command 5 at settings source 5, custom slot 65, status 3
FTL on
Active FrameTime Lock enabled, adjusting external clock gen frequency
user command x at settings source 5, custom slot 65, status 3
preferScalingRgbhv: off
user command v at settings source 5, custom slot 65, status 3
serial command Z at settings source 5, custom slot 65, status 3
user command i at settings source 5, custom slot 65, status 3
Active FrameTime Lock enabled, adjusting external clock gen frequency
user command r at settings source 5, custom slot 65, status 3
Deinterlacer: Motion Adaptive
user command r at settings source 5, custom slot 65, status 3
Deinterlacer: Motion Adaptive
* (debug) ign. length: 0x1A
*** (debug) ign. length: 0x65

. (debug) ign. length: 0x72
..user command q at settings source 5, custom slot 65, status 3
Deinterlacer: Bob
user command X at settings source 5, custom slot 65, status 3
ExternalClockGenerator disabled
user command w at settings source 5, custom slot 65, status 3
serial command Z at settings source 5, custom slot 65, status 3
user command v at settings source 5, custom slot 65, status 3
serial command Z at settings source 5, custom slot 65, status 3
user command 0 at settings source 5, custom slot 65, status 3
pal force 60hz off
user command w at settings source 5, custom slot 65, status 3
user command q at settings source 5, custom slot 65, status 3
Deinterlacer: Bob
user command v at settings source 5, custom slot 65, status 3
serial command Z at settings source 5, custom slot 65, status 3
serial command Z at settings source 5, custom slot 65, status 3
serial command Z at settings source 5, custom slot 65, status 3
user command w at settings source 5, custom slot 65, status 3
 (debug) ign. length: 0x72
ADC offset: R:43 G:44 B:3F
clock gen reset: 108000000
sync skipped sfr wrong: 0.00
 (debug) ign. length: 0x (debug) ign. length: 0x72
ADC offset: R:43 G:44 B:3F
clock gen reset: 108000000

.*****
no signal
h: 428 v: 349 PLL:0 A:7b7b7b S:07.10.10      I:00 D:0028 m:0 ht:2345 vt: 208 hpw:   9 u: 96 s: 0 S:13 W:31
****************************
no signal
h: 511 v:   2 PLL:0 A:7b7b7b S:02.18.00      I:10 D:0028 m:0 ht:   0 vt:   0 hpw:   0 u:384 s: 0 S: 5 W:31
*********************************
no signal
h: 294 v:   2 PLL:0 A:7b7b7b S:02.1a.10      I:10 D:0028 m:0 ht:   0 vt:   0 hpw:   0 u:708 s: 0 S: 5 W:31
*********
<reset>
Scanning inputs for sources ...
Output Format: Component

preset applied: 1280x720 for NTSC 60Hz 

sync skipped sfr wrong: 0.00
user command v at settings source 5, custom slot 65, status 3
user command w at settings source 5, custom slot 65, status 3
user command w at settings source 5, custom slot 65, status 3