A Headless Mumble Client/Transceiver/Walkie Talkie/Intercom/Gateway for Single Board Computers, PCs or Virtual Environments (IP Radio/IP PTT )
talKKonnect is a headless self contained mumble Push to Talk (PTT) client complete with LCD, Channel and Volume control.
This project is a fork of talkiepi by Daniel Chote which was in turn a fork of barnard a text based mumble client. talKKonnect was developed using golang and based on gumble library by Tim Cooper. Most Libraries are however heavily vendored (modified from original). You will need to get the vendored libraries from this repo.
talKKonnect was developed initially to run on SBCs. The latest version can be scaled to run all the way from ARM SBCs to full fledged X86 servers. Raspberry Pi 2,3,3A+,3B+,4B Orange Pis, PCs and virtual environments (Oracle VirtualBox, KVM and Proxmox) targets have all been tested and work as expected. Rasperry Pi Zero W will work with a "watered down" version of talkkonnect that uses a lower sampling rate so as not to use up all of the little CPU power provided by the Zero.
I Suvir Kumar created talKKonnect for fun. I missed the younger days making homebrew CB, HAM radios and talking to all those amazing people who taught me so much. Living in an apartment in the age of the internet with the itch to innovate drove me to create talKKonnect. I also wanted to learn programming. I am in no way a professional programmer but have tried to make the talKKonnect source code readable and stable to the best of my ability. Time permitting I will continue to work and learn from all those people who give feedback and show interest in using talkkonnect.
talKKonnect was originally created to have the form factor and functionality of a desktop transceiver. With community feedback we started to push the envelope to make it more versatile and scalable.
- XML Granular configurability for many uses cases.
- Multiple Server Configurations with channel control, channel scanning and server hopping
- Streaming Audio into the channel from locally stored media file or from internet stream
- Autoprovisioning for configuring multiple talkkonnects from a centralized http provisioning server
- The User has a configurable choice of GPIO pins to use for each function on different boards
- Communications bridge to interface external (otherwise not compatible) radio systems both over the air and over IP networks.
- Interface to portable or base station radios (Beefing portable radios or UART radio boards).
- Connecting to low cost USB GPS dongles (for instance “u-blox”) for GPS tracking, Panic Alerts integration with traccar GPS tracking software.
- LCD/OLED Screen (Parallel and I2c Interface) showing relevant real time information such as server info, current channel, who is currently talking, etc.
- Local or Remote Control via a USB keyboard/terminal or SSH terminal, remote control can also be achieved over http api and/or MQTT.
- Panic button, when pressed, talKKonnect will send an alert message with GPS coordinates, followed by an email indication current location in google maps.
- API/MQTT support for remote control for commands, LED Control, Button Control, Relay Control
- Tone Based Repeater Opening Function with the ability to specify the tone frequency and duration in configuration.
- Many Other features as per suggested or requested by the community
Pictures and more information of my builds can be found on my blog here www.talkkonnect.com
You can use an external microphone with push buttons (up/down) for Channel navigation for a mobile transceiver like experience. Currently talKKonnect works with 4×20 Hitachi HD44780 LCD screen in parallel mode. Other screens like 0.96" and 1.3" OLED with I2C interface is also currently supported. Currently SPI interfaced screens are not yet supported.
Low cost Class-D audio amplifiers like PAM8403 or similar “D” class amplifiers, are recommended for talKKonnect builds.
A good shileded cable for microphone is recommended to keep the noise picked up to a minimum. I am currently experimenting with mems microphones for better audio.
Instead of the onboard sound card or USB Sound Card, you can also use a ReSpeaker compatiable HAT and achieve great audio quality results in a compact form factor.
You can connect up to 4 LED indicators that can be build on the front panel of your build to show the following statuses
- Connected to a server and is currently online
- There are other participants logged into the same channel
- Currently in transmitting mode
- Currently receiving an audio stream (someone is talking on the channel)
- Heart Beat to indicate that talKKonnect is running
- Colorized LOGs are shown on the debugging terminal for events as they happen in real time. Logging with line number, logging to file or screen or both.
- Playing of configurable alert sounds as different events happen, such as a different sound when someone "joins" the channel and another sound for someone "leaving" the channel.
- Configurable TTS prompts to announce different events for those use special use cases where it is required.
- Cusomizable Roger Beep sounds that are played at the end of each transmission.
- Muting of The speaker when pressing PTT to prevent audio feedback and give a radio communication like experience to simulate simplex mode. Both simplex and duplex settable in XML config. Duplex mode allows you to keep the speaker open for people to interrupt you while speaking.
- LCD/OLED display can show channel information, server information, who joined, who is speaking, last transmision received date and time, etc.
- Configuration is kept in a single highly granular XML file, where options can be enabled, disabled and customized.
- We have for your convinience created 4 different images that you can download and burn to your SD card so that you can get up and running quickly with a generic instance of talkkonnect working out of the box. Choose the image based on your hardware and use case. Using one of these images you will not need to follow all the complicated steps of installing and compiling everything from scratch if that seems daunting and overwhelming to you at first.
- This is an easy way to start experimenting with talkkonnect in a matter of minutes. The ability to shorten the time and lessen the barrier of entry will allow you to see if talkkonnect suits your needs.
- The network settings are set as DHCP Client so your device should get an IP Address when you connect it to your DHCP enabled network.
- After you find the IP Address of your talkkonnect device from the DHCP leases section of your router you can log in over ssh using a tool like putty or equavilent on the standard ssh port 22 using the root user with password talkkonnect. The pi user is also accessable using the password raspberry.
- NOTICE!! When using these images Talkkonnect will already by started by systemd upon boot and run in a screen instance when you boot this image. There is no reason to manually start talkkonnect. By default with no changes in settings talkkonnect will connect to our community server. If you try start up talkkonnect by hand there will be 2 instances of talkkonnect that will clash with each other and you will be connected and disconnected from the server in a endless loop.
- Since talkkonnect is already running in the background (in a screen) upon boot, you can access the running console of talkkonnect by ssh (as root) into the raspberry pi device and at the command prompt type the command screen -r to see the console of the running talkkonnect. Press the
key to see a menu of the options available to you. - We request that you to please edit the configuration file of talkkonnect.xml. This file can be found in the directory /home/talkkonnect/gocode/src/github.com/talkkonnect/talkkonnect/ Please change the XML tag talkkonnect to a name that describes you so that the members in the community channel can see who you are by name or callsign. If you do not change this setting your name in the channel will be shown as talkkonnect with some random numbers and letters so as the keep the username unique by default. You cannot have more than 1 device per username connected to the server at the same time.
- By default the images of talkkonnect will connect to our community server at mumble.talkkonnect.com port 64738 using any unique username and the password talkkonnect
- You can join our channel and start chatting with us with voice and asking us questions or make suggestions we have a warm and welcomming group of enthusiastic individuals to help you with your questions. This is a good place to hang around and chat with like minded individuals.
- The images are divided into 2 broad categories (the ones that use the respeaker hat and the ones that do not)
- For those Non-Respeaker Images (Usb Sound Card or MEMS Microphone Images) Out of the box the standard configutation XML file is set to run in PC mode so no GPIO will initalized.
- For those Respeaker Images (Rpi Zero or RPI 2/3/4 Images with Respeaker) Out of the box the standard configutation XML file is set to run in GPIO Mode and GPIO will initalized, this means the PTT Button and the LEDS on the 2 Mic Respeaker Hat will work right away. You will need to connect an external speaker to the HAT for these images.
- Feel Free to explore the various example talkkonnect.xml configurations that can be found in the directory /home/talkkonnect/gocode/src/github.com/talkkonnect/talkkonnect/sample-configs here you can find various configurations that work with LCD, OLED, LEDS and PUSH Button Switches. The files are named descriptively.
- Click Here to Download Pre-Configured SD Card Image for USB Sound Card
- This image uses the standard 32 Bit Sampling and will work properly with all mumble clients on windows, android and iphone with good quality sound.
- Since 32 Bit Sampling is used this will only work reliably on Raspberry 2 Series, 3 Series and 4 Series an NOT on Raspberry PI Zero.
- This image has been configured to work with a external USB sound card (Works with CM-108 Chipsets) out of the box
- The on board sound card for RPI is disabled so you will not get any output from the onboard sound card
- The audio out on the USB Sound Card is low and needs to be amplified with and external Amplifier (for testing you can increase the volume and use a 3.5mm Jack Headphone)
- This image is a good starting point if you already have all the components at home or if you want to use talkkonnect as a Transceiver interface.
- Should you want to connect a screen and a physical PTT Button using GPIO you can set the tag
- After you intall the image you can copy the bash script tk-update.sh in the scripts folder to your /root home and run it in the root user's folder to update to the lastest version.
Quick Download Link for Pre-Made SD Card Image for Use with Raspberry pi 2/3/4 and RESPEAKER Compatable HAT
- Click Here to Download Pre-Configured SD Card Image for Respeaker Hat
- This image uses the standard 32 Bit Sampling and will work properly with all mumble clients on windows, android and iphone with good quality sound.
- Since 32 Bit Sampling is used this will only work reliably on Raspberry 2 Series, 3 Series and 4 Series an NOT on Raspberry PI Zero.
- This image has been configured to work with a Respeaker HAT out of the box so I2S, I2C and all required modules are installed and running.
- The XML file is configured to run in rpi mode so GPIO will initalized, this is so that the respeaker will work with output sound on the headphone jack, led strip working and push button microswitch on the hat can be used for transmitting.
- This image is a good starting point if you already have all the components at home or if you want to use talkkonnect as a push to talk headless device to talk directly to other mumble clients.
- After you intall the image you can copy the bash script tk-update.sh in the scripts folder to your /root home and run it in the root user's folder to update to the lastest version.
Quick Download Link for Pre-Made SD Card Image for Use with Raspberry pi 2/3/4 and IM69D130 Mems Microphone
- Click Here to Download Pre-Configured SD Card Image for talkkonnect with IM69D130 Mems Microphone
- This image uses the standard 32 Bit Sampling and will work properly with all mumble clients on windows, android and iphone with good quality sound.
- Since 32 Bit Sampling is used this will only work reliably on Raspberry 2 Series, 3 Series and 4 Series an NOT on Raspberry PI Zero.
- This image has a custom kernel and used Instructions was found at https://github.com/Infineon/GetStarted_IM69D130_With_RaspberryP (for MEMS support)
- This image has been configured to work with a IM69D130 Mems Microphone and the onboard raspberry pi sound card (3.5mm Jack) out of the box.
- The XML file is configured to run in rpi mode so GPIO will initalized, this is so that the Pin 11 XML tag value 17 when shorted to ground will act as the PTT button. This mems microphone will enable you to have a small build with excellent sound quality whilst using the internal provided sound card in the raspberry pi.
- For the wiring of the microphone to Raspberry Pi See This inmp411 wiring diagram
- After you intall the image you can copy the bash script tk-update.sh in the scripts folder to your /root home and run it in the root user's folder to update to the lastest version.
Quick Download Link for Pre-Made SD Card Image for Use with Raspberry pi ZERO With RESPEAKER Compatable HAT
- Click Here to Download Pre-Configured SD Card Image for talkkonnect for Raspberry PI Zero with Respeaker
- This image uses NON-STANDARD 16 Bit Sampling and will NOT work properly with all standard mumble clients!!
- This image is good for those who want to make a small portable device and are serious about form factor.
- Since Raspberry Pi Zero has a low powered single core CPU and no Neon Support this image was created specially for Raspberry Pi Zero. It is recommended only for communication with other talKKonnect clients or Gumble forks, regardless of their "flavor". There could be audio issues when communicating to Plumble/ Mumla and official Mumble client. Issues are not caused by talKKonnect or Gumble design. If users would still prefer to use this type of a build for communication to Plumble/Mumla and offical Mumble, we can not provide support for solving audio quality issues as they do not have root cause in talKKonnect / Gumble.
- Use this image if you want to create a group of users all using the Raspberry Pi ZERO it wont work reliably with other standard mumble clients. You have been Warned!
- This image has serial console support so you can connect via serial port or plug the raspberry pi Zero into your windows laptop and access it over Putty. You can follow instructions from Adafruit here to connect over serial from windows.
- Do not attempt to update the version of talkkonnect with this image otherwise it will break talkkonnect and your volume level and muting on transmit!
- This image is provided for those who insist they want to use Raspberry Pi zero despite our recommendations to use minimum RPI 3.
Download the latest version of Raspberry Pi OS Lite. At the time of making/updating this document latest image release date was 11/01/2021 (Kernel Version 5.4). Download the 438MB ZIP file and extract IMG file to some temporary directory.
It is recommended that you use the raspberry Pi Imager for Windows or any USB / SD card imaging software for Windows or your other OS. Some of the many options are:
After downloading a standard image and using the imaging tool, insert the SD card into your Raspberry Pi, connect the screen, keyboard and power supply and boot into the OS.
Log in as user “pi” with password “raspberry” (this is the default username and password for a fresh install of Raspbian)
sudo passwd root
Log out of the account pi and log into the root account with your newly set password
Run raspi-config and expand the file system by choosing “Advanced Options”->”Expand File System”. Reboot.
Next go to “Interfacing Options” in raspi-config and “Enable SSH Server”.
/etc/ssh/sshd_config
#PermitRootLogin prohibit-password to PermitRootLogin yes
service ssh restart
With windows you can browse to your SD card and place the blank file ssh in the root folder.
Now you should be able to log in remotely via ssh using the root account and continue the installation.
adduser --disabled-password --disabled-login --gecos "" talkkonnect
usermod -a -G cdrom,audio,video,plugdev,users,dialout,dip,input,gpio talkkonnect
apt update
(Note: If building talkkonnect on other than Raspberry Pi board, install mplayer instead of omxplayer)
apt install libopenal-dev libopus-dev libasound2-dev git ffmpeg omxplayer screen
To get the newer versions of golang used for this project I suggest installing a precompiled binary of golang. If you use apt-get to install golang at this moment you will get an older incompatible version of golang.
To install GO as required for this project on the raspberry pi. First with your browser look on the website https://golang.org/dl/ on your browser and choose the latest version for the arm archecture. At the time of this writing the version is go1.15.6.linux-armv6l.tar.gz.
Please Note that if you use apt-get to install golang instead of follow the recommended instructions in this blog you will get the following error when compiling BackLightTime.Reset undefined (type * time.Ticker has no field or method Reset)
As root user Get the link and use wget to download the binary to your talkkonnect
cd /usr/local
wget https://golang.org/dl/go1.15.6.linux-armv6l.tar.gz
tar -zxvf go1.15.6.linux-armv6l.tar.gz
nano ~/.bashrc
export PATH=$PATH:/usr/local/go/bin
export GOPATH=/home/talkkonnect/gocode
export GOBIN=/home/talkkonnect/bin
export GO111MODULE="auto"
alias tk='cd /home/talkkonnect/gocode/src/github.com/talkkonnect/talkkonnect/'
Then log out and log in as root again and check if go in installed properly
go version
You should see the version that you just installed if all is ok you can continue to the next step
Decide if you want to run talKKonnect as a local user or root? Up to you.
su talkkonnect
cd /home/talkkonnect
mkdir /home/talkkonnect/gocode
mkdir /home/talkkonnect/bin
export GOPATH=/home/talkkonnect/gocode
export GOBIN=/home/talkkonnect/bin
cd $GOPATH
go get -v github.com/talkkonnect/talkkonnect
cd $GOPATH/src/github.com/talkkonnect/talkkonnect
Before building the binary, confirm all features which you want enabled, the GPIO pins used and talKKonnect program configuration by editing file:
/home/talkkonnect/gocode/src/github.com/talkkonnect/talkkonnect/talkkonnect.xml
go build -o /home/talkkonnect/bin/talkkonnect cmd/talkkonnect/main.go
cd /home/talkkonnect/bin
./talkkonnect
cd
sudo nano talkkonnect-run
#!/bin/bash
killall -vs 9 talkkonnect
sleep 1
reset
sleep 2
/home/talkkonnect/bin/talkkonnect
chmod +x talkkonnect-run
You can start talKKonnect automatically on Raspberry Pi start up with “screen” program help. Add this line to /etc/rc.local file. before “exit 0”:
screen -dmS talkkonnect-radio /root/talkkonnect-run &
Then connect to active screen session with command “screen -r”. Exit the screen session with “Ctrl-A-D”.
┌────────────────────────────────────────────────────────────────┐
│ _ _ _ _ _ │
│ | |_ __ _| | | _| | _____ _ __ _ __ ___ ___| |_ │
│ | __/ _` | | |/ / |/ / _ \| '_ \| '_ \ / _ \/ __| __| │
│ | || (_| | | <| < (_) | | | | | | | __/ (__| |_ │
│ \__\__,_|_|_|\_\_|\_\___/|_| |_|_| |_|\___|\_ _|\__| │
├────────────────────────────────────────────────────────────────┤
│A Flexible Headless Mumble Transceiver/Gateway for RPi/PC/VM │
├────────────────────────────────────────────────────────────────┤
│Created By : Suvir Kumar <suvir@talkkonnect.com> │
├────────────────────────────────────────────────────────────────┤
│Press the <Del> key for Menu or <Ctrl-c> to Quit talkkonnect │
│Additional Modifications Released under MPL 2.0 License │
│Blog at www.talkkonnect.com, source at github.com/talkkonnect │
└────────────────────────────────────────────────────────────────┘
[Talkkonnect Version 1.59.01 Released February 27 2021
For those of you who wish to use a 0.96 or 1.3 inch OLED screen follow the instructions below (logged in as root)
enabling i2c read and Follow Step 1 - Enable I2C Interface.
For detecting the address of your screen install the tool below
apt-get install -y i2c-tools
Then using i2cdetect to detect your screen following the instructions on the same page under the section Testing Hardware (Optional)
Once you get the address note that it will be in HEX you will have to convert this address to decimal to put in the talkkonnect.xml file under the xml tag 60
In the example above I got the address 3c from i2c tools and converted that to decimal value 60.
For your audio input and output to work with talKKonnect, you needs to configure your sound settings. Configure and test your Linux sound system before building talKKonnect. talKKonnect works well with ALSA. There is no need to run it with PulseAudio. Any USB Sound cards supported in Linux, can be used with talKKonnect. Raspberry Pi’s have audio output with BCM2835 chip, but unfortunately no audio input, by the design. This is why we need a USB sound card. Many other types of single board computers come with both audio output and input (Orange Pi). USB Sound cards with CM sound chips like CM108, CM109, CM119, CM6206 chips are affordable and very common.
When connected to a Raspberry Pi, USB sound card can be identified with “lsusb” command. Typical response is something like this:
Bus 001 Device 004: ID 0d8c:000c C-Media Electronics, Inc. Audio Adapter
Audio playback devices can be listed with ”aplay -l” command.
Optional: When external USB Sound card is used, Raspberry Pi BCM2835 internal sound can be blacklisted or preveneted to load. To disable BCM2835 sound:
nano /boot/config.txt
#Disable audio (loads snd_bcm2835)
dtparam=audio=off
If the BCM2835 sound is kept enabled, the USB sound card will usually be shown as card 1. When BCM sound is disabled, USB sound will be promoted to card 0.
For talKKonnect to know what audio devices to use (BCM2835 or USB Sound), ALSA audio config file needs to be edited. Edit file /usr/share/alsa/alsa.conf,
nano /usr/share/alsa/alsa.conf and change
defaults.ctl.card 0
defaults.pcm.card 0
from default BCM2835 audio index (0) to the USB Sound index (1)
#defaults.ctl.card 0
#defaults.pcm.card 0
defaults.ctl.card 1
defaults.pcm.card 1
(This change is not necessary if BCM2835 was disabled. USB sound card will be assigned card index number “0” in that case)
USB sound device can also be set in local profile (this step is not necessary if you have used the global configuration above)
nano ~/.asoundrc
For simple USB card cards .asound configuration like this will work:
pcm.!default {
type asym
capture.pcm "mic"
playback.pcm"speaker"
}
pcm.mic {
type plug
slave {
pcm"hw:1,0"
}
}
pcm.speaker {
type plug
slave {
pcm"hw:1,0"
}
}
When creating .asoundrc. match the sound card index number to the exact number of the device in your system. Run ”aplay -l” or ”amixer” to check on this. You also need to match the names of capture and playback devices in this config file for your particular sound device.
Note: If the sound device was configured in global /usr/share/alsa/alsa.conf configuration file, there is no need to create a local .asoundrc file.
Microphone or input device needs to be “captured” for talKKonnect to work. Run alsamixer and find your input device (mic or line in), then select it and press a space key. Red “capture” sign should show under the device in alsamixer.
speaker-test
You should hear white noise.
arecord –f CD | aplay
You should hear yourself speaking to the microphone.
Adjust your preferable microphone sensitivity and output gain through “alsamixer” or “amixer”, which requires some trial and error.
For a speaker muting to work when pressing a PTT, you need to enter the exact name of your audio device output in talKKonnect.xml file. This name may be different for different audio devices (e.g. Speaker, Master, Headphone, etc). Check audio output name with “aplay”, “alsamixer” or “amixer” and use that exact device name in the configuration.xml .
┌──────────────────────────────────────────────────────────────┐
│ _ __ ___ __ _(_)_ __ _ __ ___ ___ _ __ _ _ │
│ | '_ ` _ \ / _` | | '_ \ | '_ ` _ \ / _ \ '_ \| | | | │
│ | | | | | | (_| | | | | | | | | | | | __/ | | | |_| | │
│ |_| |_| |_|\__,_|_|_| |_| |_| |_| |_|\___|_| |_|\__,_| │
├─────────────────────────────┬────────────────────────────────┤
│ <Del> to Display this Menu | <Ctrl-C> to Quit talkkonnect │
├─────────────────────────────┼────────────────────────────────┤
│ <F1> Channel Up (+) │ <F2> Channel Down (-) │
│ <F3> Mute/Unmute Speaker │ <F4> Current Volume Level │
│ <F5> Digital Volume Up (+) │ <F6> Digital Volume Down (-) │
│ <F7> List Server Channels │ <F8> Start Transmitting │
│ <F9> Stop Transmitting │ <F10> List Online Users │
│ <F11> Playback/Stop Stream │ <F12> For GPS Position │
├─────────────────────────────┼────────────────────────────────┤
│<Ctrl-D> Debug Stacktrace │ │
├─────────────────────────────┼────────────────────────────────┤
│<Ctrl-E> Send Email │<Ctrl-N> Conn Next Server │
│<Ctrl-F> Conn Previous Server│<Ctrl-P> Panic Simulation │
│<Ctrl-G> Send Repeater Tone │<Ctrl-S> Scan Channels │
│<Ctrl-V> Display Version │<Ctrl-T> Thanks/Acknowledgements│
├─────────────────────────────┼────────────────────────────────┤
│<Ctrl-L> Clear Screen │<Ctrl-O> Ping Servers │
│<Ctrl-R> Repeat TX Loop Test │<Ctrl-X> Dump XML Config │
├─────────────────────────────┼────────────────────────────────┤
│<Ctrl-I> Traffic Record │<Ctrl-J> Mic Record │
│<Ctrl-K> Traffic & Mic Record│<Ctrl-U> Show Uptime │
├─────────────────────────────┼────────────────────────────────┤
│ Visit us at www.talkkonnect.com and github.com/talkkonnect │
│ Thanks to Global Coders Co., Ltd. for their sponsorship │
└──────────────────────────────────────────────────────────────┘
youtube-video is a video made for explaining the xml tags
- The account section can have multiple accounts, talkkonnect will look for the first account with the xml tag default = "true" and attempt to connect to that server
- When talkkonnected is connected to a server you can cycle through accounts in which enabled = "true" by pressing CTRL-N, talkkonnect will connect to the next enabled server in the list
- Talkkonnect will not attempt to connect to a server that has the account tag set default = "false"
- The tag account name is just used to identify the server for logging purposes
- The serverandport tag is for the server FQDN or IP address followed by ":" (colon) and the port of mumble is running on for that particlar server.
- The username tag is used for identifying yourself on the mumble server and for authentication
- The password tag is used if the mumble server requires password authentication
- The insecure tag should be set as true if the server you are connecting to does not require a certificate
- The certificate tag should contain the full path to your previously generated certificate which is usually a file with the extension of pem
- The channel tag should only be populated want to connect to a specific channel other than the root channel on startup
- The outputdevice tag should be set as the default audio output device that represents your audio output device when you run alsamixer. Examples are Speaker or Headphone etc. (Please note that the device name should be set exactly as shown in alsamixer.
- The logfilenameandpath tag should contain the full path to a writable file that is created prior to running talkkonenct for logging purposes
- Should you not require logging to screen set the logging tag to screen. Any other value will result logs to be shown on the screen and in the log file (note that if logging is not set to screen the logs will no longer be colorized)
- The daemonize tag is not currently supported. To run at startup and in the background you can configure in /etc/rc.local talkkonnect to run in a screen session.
- Cancellable Stream is used so that if you are streaming some audio via talKKonnect another user in the channel can stop your streaming by pressing PTT.
- Simplexwithmute is used to set simplex mode (mute speaker when transmitting) or full duplex mode (not mute speaker with transmitting)
- Nextserver index should be set to 0 as default, this is used to inform talKKonnect which server to connect to the next tim talKKonnect runs
- Autoprovisioning is provided so that you can remotely provision a talkkonnect machine via http protocol from a web server
- The autoprovisioning tag when set to true or false turns on and off the autoprovisioning function respectively
- The tkid tag is used to set the autoprovisioning filename (xxxx.xml) that talkkonnect will request from the autoprovisioing web server
- The URL tag is used to define the url of the autoprovisioning webserver that hosts the configuration XML file
- The savefileandpath tag are used to define the name and where the http fetched xml file will be stored locally. This is usually /home/talkkonnect/gocode/src/github.com/talkkonnect/talkkonnect/talkkonnect.xml
- The beacon function was created to emulate a radio repeater beacon that will play certain wav files at defined periods to notify all users on a particular channel that the repeater is online nad functioning
- The beacontimersecs is the interval time in seconds between the repleated messages
- The beaconfileandpath is the tag which defines the file and path to a wav file that to be played at regular intervals
- The volume tag can be set from 0.1 to 1 in intervals of 0.1 for setting up the volume the file playback into stream will be played
- This section was created for users that want an audible response to events that happen (Users without LCD Screen)
- You can disable the whole section TTS functionality by the tag tts enabled = false
- You can choose to enable only certain events you are interested in by setting tag tts enabled = true and selecting the tag you want for your particular use case
- Talkkonnect currently can only connect to gmail's SMTP for sending emails
- Define your gmail username and password along with the receiver of the email message in their respective tags
- Define the subject and fixed message body of the email in their respective tags
- Should you want to send the GPS timestamp in the email set the gpsdatetime tag to true (You have to have a USB GPS Dongle Connected and Configured for this to work)
- Should you want to send by email your current GPS position in LAT and LONG coordinates you can enable this tag
- If you want to include the url with your pinned location on google maps enable the googlemapurl tag
- Each sound item can be enabled/disabled and the corresponding playback volume can be also be set individually
- Each event such as when a person joins a channel, leaves a channel or sends a message into the channel can be configured seperately.
- The filenameandpath tag should contain the the full path and filename of the WAV file you wish to play for each event
- The event tag is used to play an audible alert when there are changes of other users statuses
- The alert tag is used to play an WAV file into the stream to the receiving party upon a user generated panic request
- The rogerbeep tag is used to define the WAV file to play at the end of every transmission
- The tag name stream, This function is very powerful and can be used to define a local file or network stream that will be played into the mumble channel upon pressing the F11 key. Very useful for debugging.
- The txtimeout tag is used to limit the length of a single transmission in seconds. This tag is useful when used as a repeater between RF and mumble.
- API section enables the user to granually control which remote control functions are available over http within the network
- The tag apilisten port defines the port that talkkonnect should listen and respond to remote control http requests
- To use httpapi you can use your browser to go to the url http://{talkkonnectip}/?command=F1 (Replace {talkkonnectip} with the IP address of your talkkonnect)
- HTTPAPI commands supported are F1 Channel Up (+), F2 Channel Down (-), F3 Mute/Unmute Speaker, F4 Current Volume Level, F5 Digital Volume Up (+), F6 Digital Volume Down (-), F7 List Server Channels, F8 Start Transmitting, F9 Stop Transmitting, F10 List Online Users, F11 Playback/Stop Stream, F12 For GPS Position, Ctrl-E Send Email, Ctrl-L Clear Screen, Ctrl-M Ping Servers, Ctrl-N Connect Next Server, Ctrl-P Panic Simulation, Ctrl-S Scan Channels, Ctrl-X Dump XML Config
- This function is useful for debugging the values read from each section of the config xml file. You can control which section is shown. This command is tied to the CTRL-X key
- Talkkonnect can be remotely controlled by an public or local MQTT Server
- This eliminates the problem of controlling those talkkonnect devices that are in NATTED networks all over the internet
- You can subscribe to the mqtt server topic of your choice
- With MQTT you can remote control talkkonnect as well as Relays to control external devices
Below are Valid Commands for MQTT
- DisplayMenu - To Display the Menu on the talkkonnect console
- ChannelUp - To Command talkkonnect to move up 1 channel
- ChannelDown - To Command talkkonnect to move down 1 channel
- Mute-Toggle - Mute/Unmute talkkonnect depending on last state (Output of Sound Card)
- Mute - Force Mute of Speaker (Output of Sound Card)
- Unmute - Force Unmute of Speaker (Output of Sound Card)
- CurrentVolume - Get Current Volume of speaker (Output of Sound Card)
- VolumeUp - Increase the Volume of speaker (Output of Sound Card)
- VolumeDown - Decrease the Volume of speaker (Output of Sound Card)
- ListChannels - List Channels in the Server you are currently connected to
- StartTransmitting - Force talkkonnect to start transmitting
- StopTransmitting - Force talkkonnect to stop transmitting
- ListOnlineUsers - List online users to talkkonnect console
- Stream-Toggle - Start/Stop HTTP Stream or the playing of local file over the mumble channel to all users
- GPSPosition - Get Current GPS Position from UBLOX Serial GPS Receiver
- SendEmail - Send Email with User Information and predefined message
- ConnPreviousServer - Connect to the next server in talkkonnect.xml configuration file
- ConnNextServer - Connect to the previous server in talkkonnect.xml configuration file
- ClearScreen - Clear the talkkonnect console
- PingServers - Ping mumble server and show results on console
- PanicSimulation - Send distress signal over the channel
- RepeatTxLoop - Repeat tx and rx 100 times for testing
- ScanChannels - Scan the channels in the server and stop at channel with user online
- Thanks - Show Acknowledge menssage on talkkonnect console
- ShowUptime - Show uptime to user on the console of how long talkkonnect session has been running
- DumpXMLConfig - Dump XML config file on talkkonnect console
- attentionled:on - Turn on Attention LED connected on gpio pin as defined in talkkonnect.xml
- attentionled:off - Turn off Attention LED connected on gpio pin as defined in talkkonnect.xml
- attentionled:blink - Blink Attention LED connected on gpio pin as defined in talkkonnect.xml
- relay1:on - Turn on Relay connected on gpio pin as defined in talkkonnect.xml
- relay1:off - Turn off Relay connected on gpio pin as defined in talkkonnect.xml
- relay1:pulse - Pulse Relay connected on gpio pin as defined in talkkonnect.xml
- PlayRepeaterTone - Play Predefined frequency and duration of repeater tone as per talkkonnect.xml file
For Example on the topic thailand/bangkok/company/talkkonnect/attentionled:on will turn on the LED to get the attentionled of a user.
Another Example on the topic thailand/bangkok/company/talkkonnect/relay1:pulse will simulate a push button for example to open the door for a an access control system
For the above example to work you will have to specify the gpio pin in the section of the xml file
- The tag targetboard has 2 option (1) pc and (2)rpi. pc mode is used when talkkonnect is running on a pc or server that does not have GPIOs and is not interfaced to buttons and a LCD screen.
- To run on raspberry pi or other compatible single board computers set the targetboard to rpi this will enable the GPIO outputs/inputs.
- This section is used to define how the raspberry pi hardware (GPIO) is connected to the LED indicators
- The voiceactivitypin tag defines the GPIO pin that will go to Logic HIGH and light up with there is someone transmitting on the mumble channel
- The participantsledpin tag defines the GPIO pin that will go to Logic HIGH and light up when there are other users logged into the same mumble channel as you
- The transmitledpin tag defines the GPIO pin that will go to Logic HIGH when you are transmitting on talkkonnect
- The onlineledpin tag defines the GPIO pin that will go to Logic HIGH when you are authenticated and connected to a mumble server
- The heartbeat tag defines the GPIO pin that will toggle as per the defined values to show that talkkonnect is alive and operational
- Note that this heartbeat can uses the same GPIO PIN and voiceactivitypin so that one LED can have dual function
- Note Disable heartbeat or do not use the same pin as voiceactivity LED if you connect talKKonnect to a transceiver
- This section defines the raspberry GPIO pins that are connected to push buttons that are pulled to ground by keypress and float upon release
- The txbuttonpin tag is connected to the PTT push button
- The txtogglepin tag is connected to the PTT toggle button (Press and Release to Change State from RX to TX and vice versa)
- The upbuttonpin tag is connected to the channel up button
- The downbuttonpin tag is connected to the channel down button
- The panic button tag is connected to a button that will set the talkkonnect into panic mode (request for help)
- This function allows the user to set 2 possible messages like for example away messages depending on the state of a toggle switch
- When another party using talkkonenct presses F10 they can see the username along with the defined message (depending on the position of the switch on/off) in square brackets
- The commentbuttonpin tag defines the GPIO pin that the toggle switch is connected to
- At this moment talkkonnect supports the easily available 4 lines 20 characters HD44780 LCD Module.
- To disable this screen option you can set enabled = "false"
- Parallel and i2c interfacing to the HD44780 LCD Module are both supported and can be configured in this section
- Valid interfacetype tag are either parallel or i2c
- The i2c address can be obtained from running the i2cdetect -y 1 command. Convert the address displayed in HEX to Decimal and fill into the lcdi2caddress tag
- The backlight function and time is also available to turn off the LCD's backlight in case of inactivity on the channel for the defined timeout period in seconds
- The rs, e, d4, d5, d6, d7 pins are the GPIO pins that connect to the HD44780 display in parallel mode
- NOTE! You cannot use the pins 2,3 on raspberry pi for anything else other than I2C mode if you want to connect an I2C display
- At this moment talkkonnect also supports the easily available 0.96 and 1.3 Inch I2C OLED Screen.
- To disable this screen option you can set enabled = "false"
- i2c interfacing is the only option that should be specified now spi has not been developed
- The i2c address can be obtained from running the i2cdetect -y 1 command. Convert the address displayed in HEX to Decimal and fill into the lcdi2caddress tag and mostly the i2c bus is 1.
- There is no backlight function for oled screens yet
- Your will have to specify the rows and columns your screen supports (for my screen i used 8 rows and 21 columns)
- The OLED display is display width and height for my screen was 130 by 64
- Another important settings is the oledstartcolumn setting for 0.96 screens set to 0 and for 1.3 inch screens set to 1. This will clear any garbage you see on the edge of the screen.
- NOTE! You cannot use the pins 2,3 on raspberry pi for anything else other than I2C mode if you want to connect an I2C display
- Talkkonnect supports a ublox 6 USB module to provide GPS tracking on Panic mode activation
- Set the enabled tag to false if you do not have a USB dongle connected
- Define the port which the GPS is detected as in linux usually /dev/ttyACM0
- Define all other serial port settings such as serial baud, even/odd/none parity, also stop and databits.
- The panic function can be enabled or disabled and is used to request for help
- Filenameandpath tag is used to define the WAV file that will be played into a stream if the panic button is pressed
- The volume tag defines the playback volume of the wav file into the stream
- The sendident will send the contents of the ident tag defined in the account section. This is used in case you want for example your Name or alternate ID sent in the panic message.
- The panicmessage tag defines the text message that will be sent to the parent channel and all child channels if recursivemessage is set as true when the panic button is pressed
- The sendgpslocation tag enables the sending of the gps coordinates of the talkkonnect requesting help as a text message
- The txlock enabled tag will lock up talkkonnect in transmit mode for the defined txlocktimeoutsecs after the button is pressed so the requester can talk without having to press ptt button
We invite interested individuals to provide feedback and improvements to the project. Currently we do not have a WIKI so send feedback to suvir@talkkonnect.com or open and Issue in github you can also check my blog www.talkkonnect.com for updates on the project
You can also connect with a standard mumble client to our community server to have a chat or ask questions at mumble.talkkonnect.com port 64738 you can use any username with the password talkkonnect
Please visit our blog for our blog or github for the latest source code and our facebook page for future updates and information.
Thank you all for your kind feedback sent along with some pictures and use cases for talkkonnect.
talKKonnect is open source and available under the MPL V2.00 license.
suvir@talkkonnect.com Updated 10/06/2021 talkkonnect version 1.63.01 is the latest release as of this writing.