sandeepmistry/arduino-CAN

Issues

• CAN.filter(...) has no effect

  #76 opened 3 years ago
  1

• Not Working with ESP Wroom32 E

  #75 opened 3 years ago
  14

• https://github.com/sandeepmistry/arduino-CAN

  #73 opened 4 years ago
  0

• How to verify SN65HVD230 is somehow functional

  #72 opened 4 years ago
  7

• CAN will not work on M5Core2?

  #70 opened 4 years ago
  6

• Possibly missing packets?

  #67 opened 2 years ago
  1

• High speed sender

  #66 opened 4 years ago
  2

• Leading 0 are not printed

  #65 opened 4 years ago
  1

• Unable to run lib on Firebeetle-ESP32

  #64 opened 4 years ago
  1

• Can’t get this library working with esp32

  #63 opened 4 years ago
  9

• CAN running at half speed

  #62 opened 4 years ago
  16

• CANControllerClass::flush() is emplty

  #61 opened 4 years ago
  0

• How to clear TX buffer

  #60 opened 4 years ago
  9

• J1939, CAN2.0B standard and Arduino MKR CAN shield

  #59 opened 4 years ago
  1

• Change RX/TX pins

  #58 opened 4 years ago
  6

• Sending and receiving

  #56 opened 4 years ago
  3

• Potential Issue when using defined CS pin

  #55 opened 4 years ago
  1

• ESP32 with internally used SJA1000 hangs completely up when CAN wires are shorted

  #54 opened 4 years ago
  4

• CAN bus fault detection

  #53 opened 4 years ago
  10

• Cannot get CAN library and SPI display (ILI9341) working at the same time

  #52 opened 4 years ago
  4

• How to sent and recieve int?

  #51 opened 4 years ago
  1

• Send and receive bits

  #50 opened 4 years ago
  2

• General Question: convert raw data to a can message

  #48 opened 4 years ago
  1

• Even example code doesn't always work

  #44 opened 4 years ago
  4

• question with the include files used in ESP32SJA1000.cpp file

  #43 opened 4 years ago
  1

• CAN bus filter does not work as expected

  #42 opened 4 years ago
  11

• MCP2515 `observe` sets configuration mode

  #40 opened 4 years ago
  0

• MCP2515 Modification to support ESP32

  #39 opened 5 years ago
  0

• Arduino Mega2560 and MCP2515 not working

  #38 opened 5 years ago
  1

• How to find PIDs of a vehicle?

  #37 opened 5 years ago
  2

• Multiple CAN instances

  #36 opened 5 years ago
  4

• Processing suddenly stops after 1 second at 500kbps and 1000kbps

  #35 opened 5 years ago
  5

• Not able to get Ecu data from Jeep compass

  #34 opened 5 years ago
  1

• ESP Hangs itself - Guru Meditation Error: Core 1 panic'ed

  #33 opened 5 years ago
  2

• Issue with Can Bus Filter ID's

  #32 opened 2 years ago
  12

• MCP2515 bandwidth issues at 500K and 1Mbps -> SPI command optimizations

  #31 opened 5 years ago
  3

• Missing 83.333 kbps -> Updated and tested.

  #30 opened 5 years ago
  4

• CAN receiver receives same packet continuosly

  #29 opened 5 years ago
  0

• Is it possible to set 615,384 baud rate?

  #28 opened 5 years ago
  0

• NO LOOPBACK IN LIBRARY WITH CALLBACK EXAMPLE WITH ESP32

  #26 opened 5 years ago
  1

• No RTR receiption

  #25 opened 5 years ago
  2

• No Sleep Mode

  #24 opened 5 years ago
  1

• 48mhz not supported

  #23 opened 5 years ago
  0

• Same packet received over and over (ESP32 and 500Kbps vehicle bus)

  #21 opened 5 years ago
  15

• Filter for multiple CAN frame ids/masks

  #19 opened 6 years ago
  7

• When sending data with a length of 8 bytes, endPacket always crashes

  #18 opened 6 years ago
  1

• MCP-2515 not supported for ESP32

  #16 opened 6 years ago
  5

• Can't set 33.3kbps baudrate

  #15 opened 6 years ago
  6

• Can Bus Filter ID´s and Formating Messages.

  #14 opened 6 years ago
  4

• No communication two ESP32 with SN65HDV230 module

  #13 opened 6 years ago
  8