sinara-hw/Stabilizer

Issues

• default to rear MRX56904CV molex and DNP rear barrel

  #116 opened a year ago by jordens
  0

• Move JTAG/SWD connector to the back

  #115 opened a year ago by jordens
  0

• wrong panel PN

  #114 opened a year ago by gkasprow
  0

• v1.3.4 changelog

  #113 opened a year ago by maciejprzybysz
  7

• Obsolete microUSB connector

  #112 opened a year ago by filipswit
  1

• pull ups on DAC LDAC and CLR

  #98 opened a year ago by jordens
  22

• Frontpanel cut-outs/silkscreen for standalone enclosure

  #96 opened a year ago by nkrackow
  7

• parts availability

  #108 opened 2 years ago by gkasprow
  0

• Fragile thermals of backside barrel connector

  #110 opened 2 years ago by pmldrmota
  0

• v1.3.3 changelog

  #111 opened 2 years ago by filipswit
  0

• Header I2C bus should have pull-up resistors

  #109 opened 2 years ago by nkrackow
  2

• v1.3.2 DAC8831IBD glitch

  #107 opened 3 years ago by jordens
  1

• v.1.3.2 changelog

  #106 opened 3 years ago by gkasprow
  0

• Top overlay covers SMD pads

  #103 opened 3 years ago by maciejprzybysz
  1

• Some VIAs are not tented

  #104 opened 3 years ago by maciejprzybysz
  0

• ETH series resistors - same designators

  #99 opened 3 years ago by maciejprzybysz
  0

• Project validation causes errors

  #100 opened 3 years ago by maciejprzybysz
  0

• USB ID line not connected to ESD diode

  #101 opened 3 years ago by maciejprzybysz
  0

• On Mechanical1 (board outline) there are 3D models and unwanted free line

  #102 opened 3 years ago by maciejprzybysz
  0

• v1.3.1 Changelog

  #105 opened 3 years ago by maciejprzybysz
  0

• v1.3 changelog

  #97 opened 3 years ago by gkasprow
  0

• SMA/MCX connector pins are too long

  #94 opened 3 years ago by nkrackow
  10

• DI0/1 jitter, pulldown

  #91 opened 3 years ago by jordens
  5

• digital outputs

  #86 opened 3 years ago by jbqubit
  4

• DAC updates may cause transient spikes at specific code boundaries

  #83 opened 3 years ago by ryan-summers
  6

• BOM issue 3.3pF

  #95 opened 3 years ago by gkasprow
  1

• DI0/1 input protection

  #90 opened 3 years ago by jordens
  2

• wrong REV ID

  #89 opened 3 years ago by gkasprow
  6

• PHY_T/RD_P/N series resistance

  #92 opened 3 years ago by jordens
  1

• v1.2 changelog

  #79 opened 3 years ago by gkasprow
  1

• JTAG connector is EOL

  #88 opened 3 years ago by gkasprow
  1

• P12VA LED occasionally does not illuminate

  #87 opened 4 years ago by ryan-summers
  9

• LT3042 fast start was added in v1.2?

  #93 opened 4 years ago by dnadlinger
  1

• MFG issues

  #85 opened 4 years ago by gkasprow
  0

• PHY NRST pull-down

  #84 opened 4 years ago by jordens
  1

• P5V0A rail continuity

  #82 opened 4 years ago by jordens
  1

• v1.2

  #71 opened 4 years ago by hartytp
  3

• [Stabilizer v1.1] EEM I2C signals held low

  #73 opened 4 years ago by ryan-summers
  8

• [Stabilizer v1.1] Configuring RMII interface pins causes a CPU reset

  #74 opened 4 years ago by ryan-summers
  18

• test v1.2 Stabilizer with Netgear GS305P PoE ethernet switch

  #81 opened 4 years ago by gkasprow
  0

• [Stabilizer v1.1] Ethernet auto-negotiation fails with PoE switch

  #76 opened 4 years ago by ryan-summers
  7

• PoE vs. EEM power conflict

  #72 opened 4 years ago by sbourdeauducq
  10

• [v1.1 hw] JTAG TDI is shared with SPI3_NSS

  #80 opened 4 years ago by jordens
  0

• v1.1 bad power connection

  #75 opened 4 years ago by jordens
  2

• quadspi read contention

  #77 opened 4 years ago by jordens
  2

• Clean up PA0 for timing input from Pounder

  #78 opened 4 years ago by jordens
  1

• connect SMPS shield to GND at the module input

  #70 opened 4 years ago by gkasprow
  1

• LT304x fast start

  #68 opened 4 years ago by hartytp
  2

• DNP C136

  #67 opened 4 years ago by hartytp
  1

• v1.1 Testing

  #69 opened 5 years ago by dtcallcock
  2