xiao-nrf52840

There are 10 repositories under xiao-nrf52840 topic.

  • khoih-prog/Ethernet_Generic

    Simple Ethernet library for AVR, AVR Dx, Portenta_H7, Teensy, SAM DUE, SAMD21, SAMD51, STM32F/L/H/G/WB/MP1, nRF52 and RASPBERRY_PI_PICO boards using Ethernet shields W5100, W5200, W5500, W5100S, W6100. With this library you can use the Arduino Ethernet (shield or board) to connect to Internet to provides both Client and server functionalities.

    Language:C++424822

  • khoih-prog/NRF52_TimerInterrupt

    This library enables you to use Interrupt from Hardware Timers on an nRF52-based board. These nRF52 Hardware Timers, using Interrupt, still work even if other functions are blocking. Moreover, they are much more precise than other software timers using millis() or micros(). Now supports `Sparkfun Pro nRF52840 Mini`

    Language:C++19424

  • khoih-prog/NRF52_MBED_TimerInterrupt

    This library enables you to use Interrupt from Hardware Timers on an NRF52-based board using mbed-RTOS such as Nano-33-BLE. These nRF52 Hardware Timers, using Interrupt, still work even if other functions are blocking. Moreover, they are much more precise (certainly depending on clock frequency accuracy) than other software timers using millis() or micros(). That's mandatory if you need to measure some data requiring better accuracy. It now supports 16 ISR-based Timers, while consuming only 1 Hardware Timer. Timers' interval is very long (ulong millisecs). The most important feature is they're ISR-based Timers. Therefore, their executions are not blocked by bad-behaving functions or tasks. This important feature is absolutely necessary for mission-critical tasks.

    Language:C++14262

  • khoih-prog/FS_Nano33BLE

    Wrapper of FS (LittleFS or not-advisable FATFS) for Arduino MBED nRF52840-based boards, such as Nano_33_BLE boards. This library facilitates your usage of FS (LittleFS or FATFS) for the onboard flash. FS supports power fail safety and high performance

    Language:C++12231

  • khoih-prog/nRF52_MBED_PWM

    This library enables you to use Hardware Timers on nRF52840-based Nano_33_BLE or Nano_33_BLE_Sense board to create and output PWM to pins. These PWM channels, using nRF52840 Hardware Timers, still work even if other functions are blocking. Moreover, they are much more precise (certainly depending on clock frequency accuracy) than other software ir ISR-based PWM, using millis(), micros() or Timer Interrupt. This important feature is absolutely necessary for mission-critical tasks. You can start, stop, change and restore the settings of any PWM channel on-the-fly.

    Language:C3211

  • TDiblik/7941W-rfid-card-cloner

    RFID Card Cloning Device

    Language:C++3200

  • khoih-prog/NRF52_ISR_Servo

    This library enables you to use 1 Hardware PWM module on nRF52832/nRF52840-based board, such as AdaFruit Feather nRF52832, nRF52840 Express, Itsy-Bitsy nRF52840 Express, etc. to control up to 16 or more servo motors.

    Language:C++220

  • ElVit/zmk-config

    ZMK firmware for XIAO BLE

    1100

  • khoih-prog/nRF52_Slow_PWM

    This library enables you to use ISR-based PWM channels on an nRF52-based board using Adafruit_nRF52_Arduino core such as Itsy-Bitsy nRF52840 to create and output PWM any GPIO pin. It now supports 16 ISR-based PWM channels, while consuming only 1 Hardware Timer. PWM channel interval can be very long (ulong microsecs / millisecs). The most important feature is they're ISR-based PWM channels, supporting lower PWM frequencies with suitable accuracy. Their executions are not blocked by bad-behaving functions or tasks. This important feature is absolutely necessary for mission-critical tasks. These ISR-based PWMs, still work even if other software functions are blocking. Moreover, they are much more precise (certainly depending on clock frequency accuracy) than other software-based PWM using millis() or micros(). That's necessary if you need to control devices requiring high precision

    Language:C++120

  • khoih-prog/nRF52_MBED_Slow_PWM

    This library enables you to use ISR-based PWM channels on an nRF52-based board using Arduino-mbed mbed_nano core such as Nano-33-BLE to create and output PWM any GPIO pin. It now supports 16 ISR-based PWM channels, while consuming only 1 Hardware Timer. PWM channel interval can be very long (ulong microsecs / millisecs). The most important feature is they're ISR-based PWM channels, supporting lower PWM frequencies with suitable accuracy. Their executions are not blocked by bad-behaving functions or tasks. This important feature is absolutely necessary for mission-critical tasks. These ISR-based PWMs, still work even if other software functions are blocking. Moreover, they are much more precise (certainly depending on clock frequency accuracy) than other software-based PWM using millis() or micros(). That's necessary if you need to control devices requiring high precision

    Language:C201