An improved 3D printer control firmware, forked from Klipper, designed to support a large range of printers. Unlike other firmware, Catboat uses a combination of a 3D printer control board (for basic movement, heating, etc) and a standalone separate computer (usually an SBC) for anything more complex like interpreting G-code, configuration etc.
Catboat is designed to be easy to set up, easy to configure, and to support the same hardware as Klipper.
Setting up Klipper, unless you're going for a very specific setup, is frustrating, time-consuming, and requires far more technical knowledge than should be necessary. Furthermore, the 'blessed' setup method is under-documented, hard to diagnose issues with, and needlessly so. This is because Klipper currently fails to use some well-established distribution technologies which could make this effortless, or nearly so. Furthermore, certain aspects of the Klipper setup are needlessly complex even if you use a blessed setup.
Catboat aims to make the process of its setup as easy as possible: you don't have to know anything about how Linux works, or even what an IP address is in most cases. Furthermore, we provide pre-made setups (of varying levels of 'pre-made') for those who just want a plug-and-play solution. At the same time, we don't neglect the needs of the more technically-oriented. Throughout, we aim for documentational clarity: everything should be spelled out in enough detail that someone could replicate our work, and see the logic behind it, without having to guess or experiment.
Klipper is, on the whole, a brilliant idea, and continues to improve. We don't want to exclude ourselves (or our users) from these improvements. Additionally, we want to make moving from Klipper to Catboat as effortless as possible. We make it a goal that 'any valid Klipper config is also a valid Catboat config'; all you have to do is copy over your old config, and you're golden.
We also regularly merge upstream Klipper into Catboat: no feature in upstream Klipper should be missing from Catboat for long.
Klipper suffers from extreme ecosystemic homogeny: if you don't want to fund the RPi Foundation (and there are good reasons not to), you're left out in the cold. Furthermore, even in this case, the documentation is spotty at best, and misleading at worst. This is 100% a problem that could be solved, and Catboat aims to do so. In particular, we aim to provide two things:
- A general, easy-to-run configuration process, which works on most Linux-capable devices; and
- A collection of multiple 'blessed' devices, which we have tested and ensure work, and provide additional 'plug-and-play' levels of support for.
We want to give our users options, and not chain them to a single source, which is brittle at best, dangerous at worst. We have the means to do so, and Catboat aims to be the end by which we do it.
Klipper has historically been quite strict in which features it will and won't include, aiming to support only those features that would be useful to a very general use case. While this is understandable, we also feel it is needlessly limiting, as Klipper's strongest feature is its ability to improve existing printers with very little change needed. Additionally, what is niche to one person may be very core to others, and it's arguable that Klipper's definition of 'niche' is somewhat skewed.
Catboat, on the other hand, tries to provide features that are useful, even if they're somewhat niche. This includes workarounds for tricky printer boards, additional capabilities that may not often be useful, and additional devices which Klipper may deem not fitting their goals. This is not to say we accept any and every feature: merely that we seek to cater to use cases that Klipper may not consider central enough to their goals.
For a jump start, try a KIAUH Install. Look at the Catboat wiki for more information.
See the description file. At the same time, Catboat maintains the principle of 'any valid Klipper config is also a valid Catboat config'; if you have a working Klipper config, you can use it with Catboat and still expect it to work. If this doesn't happen, it's a bug: please report it!
Test the code on your printer and provide feedback to Catboat issues, good or bad.
We maintain the same license as Klipper, which we you can find in the license
file. This is GPLv3-only according to SPDX code.