/drone-flight-controller

A quadcopter flight controller based on Arduino Uno

Primary LanguageC++MIT LicenseMIT

Quadcopter PID implementation

Build Status

1. Introduction

This Arduino sketch provides a flight controller for an X quadcopter based on an Arduino Uno board and the MPU6050 sensor.

Basically, this automation routine is an implementation of a digital PID with a refresh rate of 250Hz. The method used to calculate PID coefficients is Ziegler Nichols method. The frame of the quadcopter is based on the F450.

You can use this to calibrate your ESCs.

(i) Currently under active development.

2. Requirements

Arduino libraries:

  • Wire

3. Pin connection:

       +-------------------------+
       |        MPU-6050         |
       |                         |
       | 3V3  SDA  SCL  GND  INT |
       +--+----+----+----+----+--+
          |    |    |    |
          |    |    |    |
+---------+----+----+----+----------------+
|        3.3V  A4   A5  GND               |
|                                         |
|                                         |
|                 Arduino Uno             |
|                                         |
| #4   #5   #6   #7   #8   #9  #10   #11  |
+--+----+----+----+----+----+----+----+---+
   |    |    |    |    |    |    |    |
  (M1) (M2) (M3) (M4)  |    |    |    |
                       |    |    |    |  
                       |    |    |    |
                    +--+----+----+----+---+
                    | C1   C2   C3   C4   |
                    |                     |
                    |     RF Receiver     |
                    +---------------------+
  
Legend:
Mx : Motor X
Cx : Receiver channel x

4. Configuration

4.1 Remote configuration

By default, this sketch uses the mode 2 for RF remote, according to the following picture:

remote modes

The channel mapping is then :

Channel Command
1 ROLL
2 PITCH
3 THROTTLE
4 YAW

To change the channel mapping, update the function configureChannelMapping according to your needs:

void configureChannelMapping() {
    mode_mapping[YAW]      = CHANNEL4;
    mode_mapping[PITCH]    = CHANNEL2;
    mode_mapping[ROLL]     = CHANNEL1;
    mode_mapping[THROTTLE] = CHANNEL3;
}

4.2 PID tuning

The default PID coeffcient values might work for an F450-like quadcopter. However, you can tune them in the begining of the function pidController():

void pidController() {
    float Kp[3]        = {4.0, 1.3, 1.3};    // P coefficients in that order : Yaw, Pitch, Roll
    float Ki[3]        = {0.02, 0.04, 0.04}; // I coefficients in that order : Yaw, Pitch, Roll
    float Kd[3]        = {0, 18, 18};        // D coefficients in that order : Yaw, Pitch, Roll
    // ...
}

5. Quadcopter orientation

 Front
(1) (2)     x
  \ /     z ↑
   X       \|
  / \       +----→ y
(3) (4)
  • Motor 1 : front left - clockwise
  • Motor 2 : front right - counter-clockwise
  • Motor 3 : rear left - clockwise
  • Motor 4 : rear left - counter-clockwise

Paper plane

  • Left wing up implies a positive roll
  • Nose up implies a positive pitch
  • Nose right implies a positive yaw

The MPU6050 must be oriented as following:

  • X axis : roll
  • Y axis : pitch
  • Z axis : yaw

6. Start/stop

This sketch comes with a safety process : to start the quadcopter, move the left stick of the remote in the bottom left corner. Then move it back in center position.

To stop the quadcopter, move the left stick in the bottom right corner.

State machine