Intelligent Cooling Plate with PIC16F17146

Packed with more peripherals than I/O pins, this intelligent cooling plate — the cold plate — cools its metal surface and anything on top of it. This system is controlled by a single 20-pin, 8-bit microcontroller (MCU), which performs temperature measurements, peltier current monitoring, user interface control and safety functions. The MCU can handle this task single-handedly due to its wide array of Core Independent Peripherals (CIPs).

This README covers a usage guide and a functionality overview of the intelligent cooling plate. This is not an end product, but a demonstration of the expanding capabilities of microcontrollers. Rebuilding this demo in its entirety is possible, but it's purpose is to have pieces of its implementation copied into other practical designs. All Printed Circuit Board (PCB), Computer-Aided Design (CAD) files and nonstandard Bill of Materials (BOM) components are included in the repo for reference. A more in-depth explanation of the functionality listed below can be found in Application Note AN4889.

Software Used

Development Hardware Used

PIC16F17146
Curiosity Development Board (DM164137) (used during development)

Major Functions

These are the major functions that are implemented on the microcontroller.

Current Monitoring and Measurement

Integrated Operational Amplifier (OPAMP1)
Analog Comparators 1 and 2 (CMP1 and CMP2)
Digital-to-Analog Converters 1 and 2 (DAC1, DAC2)
Analog-to-Digital Converter with Computation (ADCC)
Fixed Voltage Reference (FVR)

OPAMP1 is implemented as a current-sense amplifier, which outputs a magnified version of the small voltage across the current shunt resistor. The output of OPAMP1 is also used internally for monitoring and measurement.

The amplified current sense output of OPAMP1 is compared to a small, set voltage level (from DAC1) using CMP1. If the output is greater, then CMP1 is high, indicating current is flowing through the system.

DAC2/CMP2 work in the same way, but are used to detect overcurrent. If the DAC2 value is exceeded by the output of OPAMP1, the MCU shuts down the Peltier plate.

Additionally, the current is measured for telemetry by the ADCC, with the FVR providing the appropriate voltage reference.

Cold Plate, Heat Sink, and MCU Temperature Monitoring

Analog-to-Digital Converter with Computation (ADCC)
Fixed Voltage Reference (FVR)
Temperature Indicator Module (TEMP)

The microcontroller measures the temperature of the top plate and its heat sink using Negative Temperature Coefficient (NTC) thermistors. It also monitors the internal temperature of the MCU die with the TEMP peripheral. The ADCC uses the FVR to ensure measurements are stable, and to provide the appropriate voltage for the TEMP peripheral.

Functional Safety Supported Setting Storage

Cyclic Redundancy Check (CRC) with Memory Scanner
Nonvolatile Memory (NVM) Control

Using the NVM and CRC CIPs, user settings are saved to EEPROM along with a CRC checksum. On start-up, the checksum is revalidated for data integrity. The CRC reduces code size and runs faster than the software could perform, by offloading it to the dedicated hardware.

Protective System Monitoring

Timer 0 (TMR0)
Windowed Watchdog Timer (WWDT)

Since the cold plate involves high currents and potentially hazardous temperatures, the WWDT is used to ensure periodic monitoring of the device is performed. If the WWDT is not triggered within a specific amount of time, the MCU resets. This way, if the firmware deadlocks, the system does not remain active, thus making sure safety is not compromised. TMR0 generates the base timing for the periodic self-check.

Single-Speed Fan Control with Dual Fan Speed Monitoring

Pulse Width Modulator with Compare 2 (PWM2)
Timer 2 (TMR2) and Timer 4 (TMR4)

To cool the Peltier plate, a PWM CIP is used to generate a speed control signal for the system fans. This allows the fans to ramp up and down depending on the conditions of the system. Additionally, the tachometer signals from the fans are monitored and counted by TMR2 and TMR4. If Fan 1 is not spinning (or stops spinning), the microcontroller will not power up the Peltier plate.

User Interface

Host Synchronous Serial Port 1 (MSSP1), in I²C mode
Timer 1 (TMR1) and Timer 3 (TMR3)
Configurable Logic Cell 1 and 2 (CLC1 and CLC2)
Pulse Width Modulator with Compare 1 (PWM1)

The user interacts with the cold plate through a push button rotary encoder and an OLED display. The OLED is controlled with an on-chip MSSP1 peripheral via I²C. Since there is dedicated MSSP hardware, the CPU can load data into the module, rather than bit-banging the I/O lines.

The rotary encoder inputs connect into two CLC CIPs to convert the signals into clockwise and counter-clockwise pulses (depending on direction). The pulses go into TMR1 and TMR3, which act as counters. The CPU can read the counters later to calculate the net rotation.

Lastly, the rotary encoder has two built-in LEDs—an orange and a blue LED. Using PWM1, these LEDs are used for a visual indication of the cold plate status:

Color	Cold Plate Status
Breathing Purple	Standby
Breathing Blue	Actively Cooling
Solid Blue	At the Target Temperature
Solid Orange	Error

Debug Print

Enhanced Universal Synchronous Asynchronous Receiver Transmitter (EUSART1)

EUSART1 is used to transmit debug messages from the MCU. It is set up to run at 115200 baud, 8 data bits and 1 stop bit.

Operation

On boot, a standby screen shows the current plate temperature, the set temperature, and whether the product is in demo mode (which limits the lowest temperature for safety).

Pressing the rotary encoder button brings up a menu that can be used to change various running parameters:

Name	Function
Go Back	Returns to Standby screen
Start	Turns on plate, goes to running status screen
Set Temperature	Changes target temperature
Hysteresis	Configures temperature hysteresis
Change Units	Selects Celsius or Fahrenheit units
Show Icons	Displays text or icons in running status screen
About	Lists developer and version info
Demo Mode Toggle	Password protected way to disable demo mode

Upon pressing Start, the MCU begins checking for various errors. If all checks pass, the plate power is enabled and the user is brought to a running status screen which shows:

Target temperature of the plate
Current temperature of the plate
MCU temperature
Current Peltier current
Cooling fan RPM

If an error occurs, power to the plate is cut, and a troubleshooting error message displays on the screen. Press the rotary encoder to clear the error and return to the standy screen. If the error is not remedied and the plate is started again, it will loop back to the same error screen.

Below is a list of the various possible errors that are continuously checked for during running operation:

Name	Error Code	Cause
PELTIER_FAN1_ERROR	1	The heat sink fan is unplugged
PELTIER_OVERCURRENT_ERROR	2	More current is pulled than the software allows
PELTIER_POWER_ERROR	3	No power is detected when the plate should be pulling current
PELTIER_GAIN_ERROR	4	The gain of the operational amplifier exceeds expected tolerance
PELTIER_INT_OVERHEAT	5	Internal MCU temperature is too hot (70°C)
PELTIER_HEATSINK_OVERHEAT	6	Heat sink is too hot (80°C)
PELTIER_SENSE_HOT_OPEN	7	Thermistor for the heat sink is disconnected
PELTIER_SENSE_COLD_OPEN	8	Thermistor for the plate temp is disconnected
PELTIER_PLATE_TEMP_LIMIT	9	Cold plate is below safe temperature
PELTIER_EEPROM_WRITE_FAIL	10	Internal EEPROM written value does not match read value.

Once started, pressing the rotary encoder button and selecting Cancel stops the plate and returns to the standby menu.

Summary

This README covered a brief overview of the functionality of the cold plate and how to operate it.

Advanced-lj/pic16f17146-cold-plate-mplab-mcc