Air-duino/Arduino-AirMCU

Issues

• 开启LTO后，401固件编译出错

  #104 opened 4 months ago by lllwan
  2

• Air001 arduino ide windows上传程序出现报错 苹果上传没有问题

  #102 opened 5 months ago by aimerl
  3

• I2c作为从机，被主机用requestFrom读取时异常

  #62 opened 9 months ago by luckycheng2017
  7

• 0.6.3版本安装报错

  #100 opened 5 months ago by WellsWang
  2

• air001 在使用arduino 中使用Serial接收数据不完整

  #96 opened 5 months ago by profacetom
  12

• Air32F103在arduino怎么下载

  #98 opened 5 months ago by cqdadalele
  2

• Air001增加1M，2M的运行速度选项

  #93 opened 6 months ago by sunnyguhz
  1

• 328P与air001编译相同项目，flash空间大一倍之多，请求优化。

  #97 opened 6 months ago by caoxuan19961206
  3

• 实现硬件定时器库

  #38 opened 6 months ago by tcwj2008
  5

• air001的flash模拟eeprom默认只有128字节

  #92 opened 6 months ago by kuugasama
  4

• air001低功耗模式

  #47 opened 10 months ago by rookieslans
  14

• Serial.write和Serial.print函数输出0xAA会变成0xFFFD

  #94 opened 6 months ago by lable
  6

• BUG: 串口接收数据必定丢包。

  #50 opened 9 months ago by MaShuilong
  7

• air001 arduino 0.6.2 测试EEPROM失败？

  #95 opened 6 months ago by profacetom
  5

• AIR001使用<Wire.h>时， Wire.endTransmission()函数异常

  #84 opened 7 months ago by hehe501
  0

• Air001若把PB6配置为SERVO引脚，会导致烧写程序困难

  #86 opened 6 months ago by StreakingJerry
  2

• 增加对于Air401的适配

  #89 opened 6 months ago by HalfSweet
  0

• 请求:Air32F103CBT6增加支持I2S

  #88 opened 6 months ago by JaffLee-China
  0

• 在arduino里面是否可以直接操作寄存器，达到直接操作未封装的硬件模块的目的

  #87 opened 6 months ago by wangshujun-tj
  1

• 实现arduino的软复位和硬件看门狗

  #78 opened 7 months ago by ls701110
  1

• 使用 build_opt.h 注入编译选项，编译时提示 'e' was not declared in this scope

  #83 opened 7 months ago by Walkline80
  1

• Air001无法启用第二个硬件串口

  #73 opened 7 months ago by Walkline80
  28

• PF_2无法正常控制

  #63 opened 7 months ago by chenxuuu
  0

• 使用外部24M晶振有问题

  #48 opened 7 months ago by jyzhkj
  12

• 示例 数码管 TM1637 程序中数码管只能控制一次

  #64 opened 7 months ago by MethodJiao
  4

• 一些引脚问题

  #77 opened 7 months ago by ErrorChen
  1

• 编译存储空间占用优化

  #76 opened 8 months ago by DWtiangu
  7

• 两个硬件串口数据混合

  #75 opened 8 months ago by lineleb
  1

• 当内存空间占用达到65%左右时程序无法运行

  #70 opened 8 months ago by lineleb
  6

• 关于AirISP 1.2.7.0 在macOS Arm中运行的问题

  #71 opened 8 months ago by ExMikuPro
  1

• 麻烦新增spi示例应用程序

  #72 opened 8 months ago by ryiot
  1

• air01 Arduino例程中驱动ST7735不能用来驱动ST7789

  #74 opened 8 months ago by 1215548
  1

• 能否支持FastLED？

  #66 opened 8 months ago by arilink
  2

• PA5引脚无PWM输出

  #69 opened 8 months ago by kcro227
  1

• AIR001的I2C作从机，接收主机用Wire.write发送过来的数据异常

  #67 opened 9 months ago by luckycheng2017
  6

• 001编译时计算的内存不准

  #68 opened 9 months ago by sunnyguhz
  1

• I2C通讯，AIR001作为从机时通讯不正常

  #65 opened 9 months ago by TiElectronic
  0

• CI的测试脚本中写死了版本号，应当根据发布的版本动态更新

  #61 opened 9 months ago by HalfSweet
  1

• 舵机函数故障

  #40 opened 9 months ago by sosoga
  4

• DS18b20无法驱动

  #59 opened 9 months ago by stosc
  3

• 希望新增一下用Flash模拟EEPROM的库

  #58 opened 9 months ago by lineleb
  1

• 反复手动复位后 ADC输出0

  #53 opened 9 months ago by createskyblue
  1

• I2C master requestFrom 异常堵塞

  #51 opened 9 months ago by createskyblue
  4

• air001 使用Adafruit_AHTX0 在begin时卡住

  #54 opened 9 months ago by bbllmaster
  1

• arduino软串口有问题

  #49 opened 9 months ago by 60999
  2

• 引入SoftwareWire时 触发来自pins_arduino.h PortNames.h 的编译器错误

  #52 opened 9 months ago by createskyblue
  1

• Air001中断冲突

  #37 opened 10 months ago by Deerczl
  8

• 链接的时候会触发一个警告，进而导致终端下面的输出全部变成红色

  #43 opened 10 months ago by HalfSweet
  0

• 实现看门狗库

  #35 opened 10 months ago by godcjiajia
  0

• 希望官方能不arduino移植到PlatformIO平台

  #36 opened 10 months ago by ls701110
  1