These Open Computers (OC) scripts will automatically tier-up, stat-up, and spread (duplicate) crops for you. Open Computers is a very powerful yet complicated mod using custom scripts, but fear not. I have made everything here as straight forward as possible to help you get your crop bot running in no time.
Obtaining these components will require access to EV circuits and epoxied (late HV). This is because you need an internet card to pull the scripts from GitHub (it is possible to create all the files manually and then copy and paste the code from GitHub, but that is not recommended). The CPU and Graphics Card can be replaced by a single APU if you feel so inclined. Both inventory upgrades are necessary.
- OC Electronics Assembler
- OC Charger
- Tier 3 Computer Case
- Central Processing Unit (Tier 2)
- Graphics Card (Tier 1)
- Redstone Card (Tier 1)
- Internet Card
- Memory (Tier 2)
- EEPROM (Lua BIOS)
- Hard Disk Drive (Tier 1, 1MB)
- Inventory Controller Upgrade
- Inventory Upgrade
- Screen (Tier 1)
- Keyboard
- Geolyzer
- Disk Drive
- OpenOS (Operating System)
Lastly, you need a Transvector Binder and Transvector Dislocator, which requires some progression in Thaumcraft. However, it is not too deep and completely doable if you are already able to make EV circuits and epoxied. Transvector Dislocator can be found under "Thaumic Tinkerer" and requires the following prerequisites on the same tab: Transvector Interface and Smokey Quartz. You will also need to complete research on Mirror Magic under "Artifice." For more information, visit https://gtnh.miraheze.org/wiki/Thaumcraft_Research_Cheatsheet.
-
Insert the computer case into the OC Electronics Assembler which can be powered directly by any GT cable
-
Shift-click all the parts into the computer case except the OpenOS floppy disk
-
Click assemble and wait until it completes
-
Rename the robot in an anvil
-
Place the robot down on the OC Charger which can also be powered directly by any GT cable
-
Insert the OpenOS floppy disk in the disk slot of the robot and press the power button
-
Follow the commands on the screen "install" --> "Y" --> "Y" (Note: The OpenOS floppy disk is no longer needed in the robot afterward)
-
Copy the following line of code into the robot (middle-click to paste) and hit enter
wget https://raw.githubusercontent.com/Animatory/ic2-crop-automation/main/install.lua -
Install the rest of the scripts by entering:
./install -
Edit the config (not recommended, but check it out) by entering:
edit config.lua -
Place the Spade and Transvector Binder into the last and second to last slot of the robot, respectively. Crop sticks will go in the third, but it is not required to put them in yourself. An axe or mattock can also be placed into the tool slot of the robot (optional) to speed up destroying crops. See image below.
First off, it is recommended to set everything up in a Jungle or Swamp biomes at Y=130 as that will give you the highest humidity and air quality stats. This is most easily done in a personal dimension which you earn as a quest reward from reaching the moon. Do not place any solid blocks above the farm as that will reduce the air quality. All the machines on the surface are waterproof so do not worry about the rain. Use vanilla dirt because that will allow you to grow crops that require a particular block underneath, and boost the nutrient stats of your crops. The whole farm can easily fit into a single chunk for easy chunk loading.
You may change both the size of the working farm and the size of the storage farm in the config (default is 6x6 and 9x9, respectively). Larger working farm sizes will extend left and up while larger storage farm sizes will extend down and to the right (see image below). The top row of the working farm will always align with the top row of the storage farm. There is no maximum or minimum size for either farm, and it does not matter if the lengths are even or odd. Note that larger storage farm sizes will leave your working farm more susceptible to weeds because the robot will have to travel further when transporting crops, which means less time spent scanning the working farm. Changing anything in the config, including these sizes, requires you to restart your robot.
First note the orientation of the robot sitting atop the OC charger. It must face up towards the right-most column of the working farm. The crop stick chest directly next to the charger can be a few things: any sort of chest, a JABBA barrel, or storage drawer (orientation does not matter). If the crop stick chest is ever empty, bad things will happen. In the image, I have a trash can on the other side of the crop stick chest because I do not want any drops beyond the target crop, but this can be a second chest if you do want random drops. The blank farmland is for the transvector dislocator which should be facing it. You can tell which direction the transvector dislocator is facing by the side that is animated. The last spot is for a crop-matron which is optional and one y-level lower than the rest of the blocks. It is just to hydrate most of the crops to help them grow a little faster.
The location of the water is completely flexible: they do not have to be in the same locations as in the photo (underneath all five sea lantern slabs), and you can have as many as you would like on both the working farm and storage farm. However, there MUST be a block on top of each water and no two can be next to each other. The block can be literally anything, even a lily pad will work, so long as there is something. It is also possible to use garden soil or fertilized dirt and have absolutely no water on the farms at all, but this will sacrifice a few nutrient stats and bar you from growing crops that require a particular block underneath.
The starting crops must be placed manually in the checkerboard pattern seen in the photo. This layout goes for all three programs. If you cannot fill the entire checkerboard to start, the absolute minimum required is two (one as the target crop and the other next to it for crossbreeding). Placing empty crop sticks to fill the rest of the checkerboard is unnecessary. The target crop is used by autoStat and autoSpread to identify the crop you want to stat-up or spread to the storage farm, respectively.
Underneath the farm, you can see that there are three additional dirt blocks below each farmland, each of which adds to the nutrient stat of the crop above it. For crops requiring a block underneath, that should be placed at the bottom. In this case, I have diareed planted on top, which means I have one farmland --> two dirt --> one diamond block underneath each one. I do not have diamond blocks underneath the working farm because the diareed does not need to be fully grown in order to spread.
For power, I am using an HV gas turbine and a super tank with some benzene (no transformer needed). This is a little overkill, but the important part is that the charger is always at 100% charging speed which you can see by hovering over it. A set-up such as this will last forever with a few hundred thousand benzene since both machines require very little EU/t. Lastly, a reservoir feeds water into the crop-matron automatically after right-clicking it with a wrench.
The first program is autoTier. This will automatically tier up your crops, terminating once the max breeding round is reached (configurable), or the storage farm is full. A storage chest is recommended for this program. Note that unrecognized crops will be moved to the storage farm first before replacing any of the lower tier crops in the working farm. Stating-up crops during this program is a configurable option. To run, simply enter:
autoTier
The second program is autoStat. This will automatically stat-up your crops, terminating once Gr + Ga - Re is at least 52 (configurable) for all crops on the working farm. A trash can is recommended for this program. Maximum growth and resistance for parent crops are also configurable parameters which default to 21 and 2, respectively. To run, simply enter:
autoStat
The third program is autoSpread. This will automatically spread (duplicate) your crops if each new Gr + Ga - Re is at least 50 (configurable), terminating once the storage farm is full. A trash can is recommended for this program. Maximum growth and resistance for new (child) crops are also configurable parameters which default to 23 and 2, respectively. To run, simply enter:
autoSpread
Fire and Forget. If you have brand-new crops (i.e., 1/1/1 spruce saplings) and want to automatically stat-up and start spreading. Note that keepMutations in the config should probably be set to false (default); otherwise, the storage farm will be overwritten once autoSpread begins. To run, simply enter:
autoStat && autoSpread
To list all the files installed on the robot, enter
ls
To remove any one file installed on the robot, enter
rm <filename>
To uninstall all the files from this repo, enter
uninstall
To view an entire error message regardless of how long it may be, enter
<program> 2>/errors.log
edit /errors.log
For starters, I recommend stating-up and spreading the following crops because their outputs are useful and not completely overshadowed by bees. Note that every crop has a higher chance of being discovered with specific parent combinations, but it is often easier to discover a crop from crossbreeding at the same tier. For example, diareed apparently has the highest chance of being discovered when the parents are oilberry and bobsyeruncle ranks, BUT I recommend just running autoTier with all Tier 12 crops (or autoSpread with keepMutations on in the config). Crops that require a particular block underneath do not need to be fully grown in order to spread. For a full list of crops and their requirements, visit https://gtnh.miraheze.org/wiki/IC2_Crops_List.
- Stickreed for discovering other crops and sticky resin (rubber dust)
- Spruce Bonsai for all of your benzene and power needs
- Glowing Earth Coral for sunnarium and glowstone (gold and redstone)
- Sugarbeet for sugar (oxygen)
- Rape for seed oil
- Goldfish plant for fish oil
- Salty root for salt (chlorine and sodium)
- Enderbloom for enderpearls/endereyes
- Diareed for diamonds
- Bobsyeruncle ranks for emeralds
My repo is a fork from https://github.com/DylanTaylor1/ic2-crop-automation which was originally authored by huchenlei and improved by xyqyear and DylanTaylor1. Huge props to them for getting this off the ground and allowing me to take it further.
If you are familiar with the older versions of this code, then here are some notable changes that motivated me to develop this fork in the first place.
- Changed general layout to access chests more easily.
- Changed farm layout to facilitate running autoSpread immediately after autoStat.
- Added the option to use regular dirt instead of fertilized dirt for crops requiring a particular block underneath.
- Added configurable maximum growth and maximum resistance stats.
- Added configurable thresholds for autoSpread, autoStat, and autoTier.
- Added a configurable option to stat-up crops while running autoTier.
- Added a configurable option to clean up after complete (no longer a flag).
- Added a built-in storage reset to prevent having to break the robot in order to run autoSpread or autoTier more than once.
- Added an uninstall script.
- Code is a LOT cleaner and more organized, just look at this README.
- It is no longer the code's fault if any of the programs crash (probably).
