Arksine/katapult

Issues

• STM32F407 not installing firmware after katapult

  #98 opened a year ago by f8m8
  5

• Get to katapult bootloader mode via serial UART1

  #135 opened 2 months ago by jarretluft
  1

• Serial Flashing broken: Error sending command [SEND_BLOCK] to Can Device

  #128 opened 4 months ago by DrKlipper
  22

• Make flash fails

  #136 opened a month ago by Eremius
  0

• CanBoot

  #132 opened 3 months ago by Mabberleys
  0

• pyserial install instructions update

  #130 opened 3 months ago by keyboard-magpie
  0

• Is posible reduce size of the final binary ?

  #120 opened 8 months ago by semos2k
  3

• flash_can.py not going into boot loader mode

  #106 opened a year ago by treaves
  3

• Flashtool reboot (`-r`) fails with write error

  #129 opened 4 months ago by ressu
  2

• [Enhancement] firmware: Support reporting the current version of Katapult.

  #87 opened 4 months ago by Laikulo
  8

• Problem using Katapult with a serial connection

  #125 opened 4 months ago by mykepredko
  3

• MKS SKIPR goes not in DFU Mode after canboot

  #107 opened a year ago by yammaster
  1

• Flashing RP2040 - "No rule to make target 'flash'. Stop.

  #121 opened 7 months ago by Burnsian
  1

• Support for STM32G431

  #124 opened 7 months ago by Samuel-0-0
  1

• Custom Board w/ STM32G0B1CEU6 - 512K

  #123 opened 7 months ago by syph3rd
  2

• RPI - UART - SKR 3 - CAN - EBB36 (UART to CAN Bridge)

  #122 opened 7 months ago by Drury13
  1

• Supported STM32 models

  #109 opened a year ago by T3AR5
  2

• Flashing RP2040 - No rule to make target 'flash'

  #96 opened a year ago by alextac98
  3

• Can't get this to work on Fly ERCF or BTT Manta M8P

  #115 opened 8 months ago by alidaf
  4

• Reboot not connecting

  #119 opened 8 months ago by afewyards
  2

• EBB42 1.2 cannot flash klipper or canboot update via CAN

  #114 opened 10 months ago by sredoje1973
  3

• Failure to manuconfig for Katapult Pi 5

  #118 opened 9 months ago by Jesusday
  1

• STM32407 SKR PRO Can katapult be loaded and function correctly

  #117 opened 9 months ago by shawnchr
  0

• Compile Error Mellow SB2040 V1

  #116 opened 10 months ago by jsuhre
  1

• Reflashing rp2040

  #113 opened 10 months ago by leadustin
  0

• [Help needed] - cause of "CONNECT timed out"on btt-mmb

  #111 opened a year ago by lesaux
  15

• Compiler error BTT EBB36 V1.0

  #112 opened a year ago by Iskaroth
  0

• Issue with make, and Error 127

  #105 opened a year ago by Z035
  1

• BTT Pi

  #108 opened a year ago by Khalid310
  0

• STM32G0B1 via STM32CubeProgrammer fails

  #92 opened a year ago by 53Aries
  2

• How to change Katapult baud rate (reflashing)

  #104 opened a year ago by iwm911
  1

• Cannot make menuconfig

  #103 opened a year ago by Z035
  2

• CanBoot / katapult has never worked with Octopus Pro 1.0 (429)

  #83 opened a year ago by Kaelum
  13

• can't flash over canboot manta E3EZ

  #102 opened a year ago by swaaws
  0

• Flashing over "pure" serial connection (Creality 4.2.7 board)?

  #100 opened a year ago by DrKlipper
  11

• EBB SB2209 CAN RP2040 - No RP2040 Option in Katapult Configuration

  #99 opened a year ago by TimGehres
  3

• Error 127

  #97 opened a year ago by stefanpieter
  1

• Clarification of "Application start offset"

  #95 opened a year ago by DrKlipper
  4

• Changing CANBUS_ID_ADMIN

  #94 opened a year ago by SVL101
  1

• Klipper can't connect to mcu via canbus after Raspbian 11 (bullseye) update.

  #80 opened a year ago by Flob74
  2

• toolboards falling off the can bus

  #84 opened a year ago by ldr
  25

• Coexisting canboot.bin and katapult.bin in katapult/out folder

  #93 opened a year ago by Phil1988
  4

• Hot-Plug ebb36 and octopus 1.1 466

  #91 opened a year ago by islonina
  2

• STM32G0 Series Workaround for BOOT0-Pin Problem

  #82 opened a year ago by skuep
  8

• Conjoin Katapult and Klipper images for single flash?

  #90 opened a year ago by WayneManion
  1

• Unable to open serial port: [Errno 11]

  #89 opened a year ago by TItan371
  0

• [Enhancement] flashtool.py: Guardrail to prevent flashing wrong MCU type.

  #86 opened a year ago by Laikulo
  1

• [Enhancement] flashtool: Support gathering system information (such as MCU name in the CONNECT response) without flashing.

  #85 opened a year ago by Laikulo
  1

• flashtool.py cannot find nodes

  #81 opened a year ago by Fuergrissa1
  4

• [FR] Return to application/Command Serial Device Reset

  #79 opened a year ago by gaby64
  1