CircuitSetup/Split-Single-Phase-Energy-Meter

Issues

• Problem in reading KWH in ATM90E32

  #79 opened 9 months ago by RamyaDidde
  1

• one channel CT channel reading differently

  #78 opened a year ago by chaseadam
  26

• Clarification on ESPHome configuration

  #76 opened a year ago by wilsongoode
  3

• Installation help

  #77 opened 2 years ago by k7faq
  3

• Energy meter solar kit installation in EU

  #75 opened 2 years ago by MassimilianoBiancucci
  2

• Calibration in EU with 230V 50Hz

  #74 opened 2 years ago by MassimilianoBiancucci
  0

• Getting 65535 values for Current and voltage

  #73 opened 2 years ago by abraralishah12
  9

• volt is reading 0.001000

  #70 opened 2 years ago by kimza90
  1

• Current and ADC voltage limits, and the PGA

  #64 opened 3 years ago by raineth
  2

• Negative values?

  #53 opened 2 years ago by scfigg
  1

• fuse suggestion

  #65 opened 3 years ago by chaseadam
  1

• Can I use a Jameco 112366 with board 1.4 rev3?

  #59 opened 2 years ago by rb28z2
  1

• cannot "unset" emoncms server in emonesp

  #57 opened 3 years ago by chaseadam
  0

• FR: Add ClientId to MQTT

  #55 opened 3 years ago by dimaj
  0

• Why in the REGULAR ENERGY MEASUREMENT is done the product by 3200?

  #69 opened 2 years ago by amolina-chargevite
  1

• Rebooting problem using emonESP with ESP32 with Arduino IDE

  #68 opened 2 years ago by albnar
  7

• Alternative way to power the v1.4 board

  #66 opened 2 years ago by foureight84
  3

• Error during compiling EmonESP scr.ino.

  #67 opened 2 years ago by albnar
  1

• Calibration emonESP from Russia

  #49 opened 3 years ago by skribbl84
  1

• Reading 65k from voltage register

  #45 opened 3 years ago by TSMotter
  5

• No Power with 3 different Jameco 9V Ac Adapters

  #58 opened 3 years ago by luisgarcia87
  1

• Use another CT sensor.

  #60 opened 3 years ago by Fresh878
  1

• CT Clamps not reading anything

  #62 opened 3 years ago by smartroad
  1

• Voltage measurement under load?

  #63 opened 3 years ago by Cat-Ion
  1

• How to avoid using Emon software

  #61 opened 3 years ago by Rivazinho
  0

• support for high frequency AC transformer?

  #51 opened 3 years ago by asalexsu
  5

• Any advice for an european transformer brand?

  #54 opened 3 years ago by wouldgo
  3

• Repeated MQTT reconnects due to emon server unavailable

  #56 opened 3 years ago by chaseadam
  1

• Can't connect to Emoncms after updating from 2.5.7 to 2.6

  #42 opened 4 years ago by zirdum
  7

• EmonESP fork

  #38 opened 4 years ago by chaseadam
  3

• No AC adapter available

  #52 opened 3 years ago by eavyon
  4

• Setting up Split Single Phase meter on emoncms.org

  #50 opened 4 years ago by farzadb
  3

• Periodic disconnects - add scheduled reboot?

  #27 opened 5 years ago by amil109
  44

• Board Compatability

  #48 opened 4 years ago by johnsethwatkins
  1

• What is the latest version 2.6 or 2.6.1

  #46 opened 4 years ago by JPElectron
  3

• fried split circuit v1.4 rev 2

  #47 opened 4 years ago by chaseadam
  2

• Won't Connect to MQTT Until Restart

  #35 opened 4 years ago by rothnic
  2

• What Calibration setting value to use for 200A CT?

  #43 opened 4 years ago by JPElectron
  5

• Power is showing negative now?

  #44 opened 4 years ago by scfigg
  7

• Switched routers... device won't connect to wifi

  #41 opened 4 years ago by zirdum
  1

• Can't flash latest esphome example

  #37 opened 4 years ago by jarrettv
  3

• Verifying Power Factor values

  #40 opened 4 years ago by chaseadam
  4

• Can we measure current with one CT only?

  #36 opened 4 years ago by aaamitsingh
  8

• When in STA mode connected to AP and AP goes away, will not auto reconnect

  #32 opened 4 years ago by kirkdwilson
  1

• No readings from CT2

  #34 opened 5 years ago by neilrees
  3

• I am getting smoke from board on IC2

  #33 opened 5 years ago by RichBoehle
  1

• No Hardware

  #28 opened 5 years ago by palmtreefrb
  5

• emonESP split phase - can I use for single phase?

  #31 opened 5 years ago by m-d-johnson
  6

• Voltage * Current != Active Power, is that correct?

  #30 opened 5 years ago by manutenfruits
  4

• Voltage calibration value

  #29 opened 5 years ago by gigawatts
  1