/ATC_MiThermometer

Custom firmware for the Xiaomi Thermometers and Telink Flasher

Primary LanguageCOtherNOASSERTION

Custom firmware for BLE thermometers on the Telink chipset.

This repository contains custom firmware for several Bluetooth Thermometer & Hygrometer devices. The download of the appropriate firmware for your device will be presented automatically in TelinkMiFlasher.html. Downloading files from this repository is not required. Alternative firmware and configurator from ATC1441 (variant ATC_Thermometer.bin) can be found here: atc1441/ATC_MiThermometer. Custom firmware is not supported in MiHome. But it is possible to work LYWSD03MMC with 'Xiaomi Gateway 3' by first registering in MiHome on the official firmware, flashing to custom firmware with restoring the binding key from MiHome, replacing the device name with "LYWSD03MMC" and setting the advertising type to "MIJIA (MiHome)" marked "encrypted".

The custom firmware can be flashed via a modern browser and over-the-air (OTA) without opening the device and unlocks several customization options. You can go back to the original firmware at any time. OTA and configuration main page - TelinkMiFlasher.html.

Key features

  • Extended battery life (over a year)
  • Improved measurement accuracy and extended format in 0.01 units
  • Full support Home Assistant 'BTHome integration'
  • Supports encrypted connections using PIN-code and encrypted bindkey beacon
  • Supports Bluetooth v5.0+ LE Long Range (LE 1M/2M/Coded 500K/125K), CSA1/CSA2 (Channel Selection Algorithm), Advertising Extensions: primary and secondary Coded PHY S=8, Connectable
  • 3 LCD Display Screens (Looping): Temperature & Humidity & Comfort, Temperature & Battery Level, Clock
  • Measurement values recording & Charting. See Reading Measurements from Flash
  • Adjustable correction offsets and Comfort zones
  • Support for 4 beacon formats: Xiaomi, ATC, Custom, BTHome and encrypted options.
  • Adjustable RF TX Power & Bluetooth advertising interval
  • DIY improvements - relay control by temperature or humidity, transmission of the reed switch status - open / closed or pulse counter

Supported models:

Xiaomi Mijia (LYWSD03MMC) Xiaomi Miaomiaoce (MHO-C401) Qingping Temp & RH Monitor (CGG1-Mijia) CGDK2 Qingping Temp & RH Monitor Lite Xiaomi Mijia MJWSD05MMC MHO-C122 (2AWMOMHOC122)
Xiaomi Mijia (LYWSD03MMC) Xiaomi Miaomiaoce (MHO-C401) E-ink CGG1 'Qingping Temp & RH Monitor', Xiaomi Mijia DevID: 0x0B48 CGDK2 Qingping Temp & RH Monitor Lite Xiaomi Mijia (MJWSD05MMC) MHO-C122 (2AWMOMHOC122)

Warnings

If you have many BLE devices, the adapter must be able to receive BLE advertisements every 3 ms. UART speeds of 921600 baud and even USB1.1 are not enough to transfer information in binary form in the HCI format. Requires BT adapter with USB2.0 HS. Otherwise, there will be many gaps in the reception.

Do not use ESP32xxx - it cannot work with BLE at normal speed and drains the batteries of all BLE devices when connected!

ESPHome does not work with Bluetooth 5.0 and misses a lot of advertising packets from BLE devices.

For reliable connection and refirmware on LYWSD03MMC, the battery level must be more than 40%. This is a design feature - a cheaper version of the hardware from Xiaomi.

On devices with missing power capacities, do not set 'Connect latency' to more than 1000 ms!

Home Assistant in "Bluetooth" integration does not full support Bluetooth 5.0 and is not implied.

How to switch the USB-BT5.0+ adapter to work in LE Long Range in Home Assistant under Linux:

On thermometers with a button, if the button function is set to Connect, then a short application on the button for 80 seconds enables connection in BT4.0 mode.

If you accidentally set the 'LE Long Range' on the thermometer, and your device does not support BT5.0, remove and insert the battery - the thermometer will switch to BT4.2 support mode.

If you have a smartphone with BT5.0+ and the nRFConnect program, then you can reset all settings to default by connecting to a thermometer and sending the 0x56 command, as shown in the screenshot:

img nRFConnect_set_default.png

To disable only the 'Long Range' option, use the code 0xDD.

The Web Bluetooth API in Chrome does not yet allow scanning for Bluetooh 5.0+ devices.

Table of content

Getting Started

You can conveniently flash, update and configure the bluetooth thermometers remotely using a bluetooth connection and a modern web browser.

Flashing or Updating the Firmware (OTA)

To flash or update the firmware, use a Google Chrome, Microsoft Edge or Opera Browser.

  1. Go to the Over-the-air Webupdater Page TelinkMiFlasher.html *
  2. If using Android, Windows, Linux: Ensure you enabled "experimental web platform features". Therefore copy the according link (i.e. chrome://flags/#enable-experimental-web-platform-features for Chrome), open a new browser tab, paste the copied URL. Now sten the Experimental Web Platform features flag to Enabled. Then restart the browser.
  3. For all sensors with a button, before activation, it is necessary to reset the past bindings by holding the button for a long time.
  4. In the Telink Flasher Page: Press Connect: The browser should open a popup with visible Bluetooth devices. Choose the according target device (i.e. LYWSD03MMC) to pair.
  5. After connection is established a Do Acivation button appears. Press this button to start the decryption key process.
  6. Now you can press the Custom Firmware ver x.x button to directly flash the custom firmware. Alternatively you can choose a specific firmware binary (i.e. the original firmware) via the file chooser
  7. Press Start Flashing.
  • Use TelinkOTA to flash old or alternative versions (ATC1441). This is a program for OTA projects with Telink SDK, no third-party (mijia) protections.

  • Addition for CGG1-M: Press and hold the button on the back of CGG1-M for 2 seconds until the Bluetooth icon starts blinking on the e-ink display, and then click the 'Connect' and 'Do Activation' buttons on the TelinkMiFlasherl.

  • Addition for MJWSD05MMC: Press and hold both buttons for a few seconds until the screen blink (device resets). Next, briefly press the top side button, then briefly press the bottom button. The Bluetooth icon will start flashing. Next 'Connect' and 'Do Activation' in TelinkMiFlasherl.

Configuration

After you have flashed the firmware, the device has changed it's bluetooth name to something like ATC_F02AED. Using the TelinkMiFlasher.html you have various configuration options.

General process:

  1. Press Connect
  2. Select the according device to connect/pair (i.e. ATC_F02AED)
  3. Several configuration options appear
  4. Choose Send Config to send changed value to the device. Or press Set default and then Send config to revert to the Defaults
Option Description
Temperature and Humidity offset Enter a value to correct the offset of the Temperature or Humidity displayed: For example -1.4 will decrease the Temperature by 1.4°
Smiley or Comfort Choose a static smiley or check the "Comfort" Radio box to change the smiley depending on current Temperature and Humidity.
Comfort Parameters Defines the Lower (Lo) and Upper (Hi) Range for Temperature and Humidity interpreted as comfort zone. In the default configuration a smiley will appear.
Advertising Type Type of supported Bluetooth Advertising Formats.
Set time sends the current time to the device
Comfort, Show batt, Clock Ticking the according boxes you can enable interval rotation between different LCD screens. See the example video below.

Example of LCD display modes

You can configure different LCD Display modes using Comfort, Show batt and Clock configuration checkboxes. The enabled LCD Display Modes will appear one-by-one in a loop.

YoutubeVideo

Battery and clock display are enabled in the settings. The rest of the settings is kept default. The video contains 2 cycles.

  1. Temperature and humidity
  2. Temperature and % of battery
  3. Temperature and humidity
  4. Hours and minutes

Firmware

Firmware Binaries

You can directly update/flash the firmware without downloading the binaries below.

Custom Firmware Versions:

The download of the appropriate firmware for your device will be presented automatically in TelinkMiFlasher.html. Downloading files from this repository is not required.

Original Manufacturer Firmware Version

In case you want to go back to the original firmware, you can download them here:

Firmware version history

Version Changes
1.2 Bind, Set Pin-code, Support MHO-C401
1.3 Get/Set comfort parameters
1.4 Get/Set device name, Get/Set MAC
1.5 Add Standard Device Information Characteristics
1.6 Fix alternation of Advertising in mi mode
1.7 Authorization and encryption in permissions to access GAP ATT attributes, if pin code is enabled
1.8 Time display (instead of a blinking smile)
1.9 Recording measurements to flash memory (cyclic buffer for 19632 measurements)
2.0 Recording measurements with averaging to flash memory
2.1 Periodic display refresh for MHO-C401
'Erase mi-keys' option to return to original firmware
2.2 Added parameter "Encrypted Mi Beacon"
2.3 Added "Delete all records"
2.4 Added parameter "Clock time step"
2.5 Remove TRG/FLG errors, minor optimization
2.6 Expanding the ranges of threshold parameters (TRG)
2.7 Reducing power consumption of MHO-C401 (EDP update), adding version for CGG1-M 2020-2021
2.8 Added saving bindkey to EEP if mi-keys are erased, reduced TX power to 0 dB for defaults
2.9 Added additional id flags to advertising packages
3.0 Added toggle support for advertising package structures for third-party software
3.1 Fix security attributes (for pincode)
3.2 Added new encrypted beacon formats, reed switch maintenance
3.3 Added autodetection for LYWSD03MMC hardware versions B1.6 and B1.9. For CGG1-M and MHO-C401 - autodetection of SHTV3 or SHT4x sensors
3.4 Correct Hardware Version Setting for LYWSD03MMC B1.7
3.5 Correction of moisture readings for SHT4x sensors. Rounding off sensor values on display.. Saving HW string B2.0 on LYWSD03MMC. Eliminated battery voltage noise in CGG1-M. CGG1 - correction of the battery charge display. Added CGDK2 and modified (DIY) variant of CGDK2-2.
3.6 Additional parameters: Support BT5.0 PHY, Channel Selection Algorithm 2, Correct RF-TX Power in suspend
3.7 Added format 'HA BLE', reed switch operation mode: Switch and Count. Full support for "HA BLE" encryption. Speed correction I2C for LCD controller LYWSD03MMC HW:1.9. Support for CGG1-M hardware version 2022.
3.8 Fix clear_memo, renaming 'HA BLE' format to 'BTHome'
3.9 Changed the calculation of battery readings in %, optimization of consumption for the solar battery when the voltage drops below 2V (deep-sleep), added option to invert event for reed switch, small optimizations.
4.0 Improved stability in connected mode. I2C bus CLK and PullUp correction.
4.1 Changed "connection latency" for stability in connected.
4.2 Option Increasing Communication Distance: Bluetooth 5.0 LE Long Range (Advertising Extensions: primary and secondary Coded PHY S=8, Connectable). Added support MHO-C401 (2022.11) and MJWSD05MMC. Added function key: Connect
4.3 Increasing the degree of averaging (x64) of the sent values over the battery. Added "Screen Off" option. Check LYWSD03MMC HW: B1.5. Added MHO-C122 (2AWMOMHOC122) test support. LCD display stabilization LYWSD03MMC HW:B1.9

Applications

Reading Measurements from Flash

GraphMemo.html

To record the measurement results, a cyclic buffer in the flash memory for 19632 measurements is used. The recording step interval is set in the interface. With the default settings, the recording step is 10 minutes, which gives a recording depth of 4 and a half months. During the step period, the sensor data and battery voltage are averaged, time stamped, and written to flash memory.

Setting the value to 0 disable logging to internal storage.

FlashData

Reading Measurements in Connected Mode

GraphAtc.html GraphAtc1.html GraphAtc2.html DevPoint.html

GraphAtc_html

Reading Measurements in Advertising Mode

This requires the Experimental Web Platform Features flag enabled in your browser. See Flashing or Updating the Firmware (OTA).

Advertising.html

Technical specifications

Average power consumption

Xiaomi Mijia (LYWSD03MMC B1.4)

Using the default settings for advertising interval of 2.5 seconds and measurement interval of 10 seconds:

  • Bluetooth Advertisement: 14..15 uA 3.3V (CR2032 over 1 years)
  • Bluetooth Connection: 14..25 uA 3.3V (CR2032 over 10 months)

PowerAdvInt

PowerLife.gif

Xiaomi Mijia (MJWSD05MMC)

Using the default settings for advertising interval of 5 seconds and measurement interval of 20 seconds:

  • Bluetooth Advertisement: 19..21 uA 3.3V (CR2450 over 2 years)
  • Bluetooth Connection: 25..30 uA 3.3V (CR2450 over 1.5 years)

Xiaomi Miaomiaoce (MHO-C401)

Using the default settings for advertising interval of 2.5 seconds and measurement interval of 20 seconds:

Xiaomi Miaomiaoce (MHO-C401N)

Using the default settings for advertising interval of 2.5 seconds and measurement interval of 20 seconds:

  • Bluetooth Advertisement: 10..14 uA 3.3V (depends on the amount of temperature or humidity changes over time to display)
  • Bluetooth Connection: 13..17 uA 3.3V (depends on the amount of temperature or humidity changes over time to display)

Qingping (CGDK2)

Using the default settings for advertising interval of 2.5 seconds and measurement interval of 20 seconds:

  • Bluetooth Advertisement: 18..21 uA 3.3V
  • Bluetooth Connection: 23..30 uA 3.3V

Qingping (CGG1)

Using the default settings for advertising interval of 2.5 seconds and measurement interval of 20 seconds:

  • Bluetooth Advertisement: 12..16 uA 3.3V
  • Bluetooth Connection: 23..30 uA 3.3V

Qingping (CGG1N)

Using the default settings for advertising interval of 2.5 seconds and measurement interval of 10 seconds:

  • Bluetooth Advertisement: 12..16 uA 3.3V
  • Bluetooth Connection: 23..30 uA 3.3V

Bluetooth Advertising Formats

The Firmware can be configured to support one of four different Bluetooth advertisements data formats:

Xiaomi, ATC, Custom, BTHome and encrypted options.

Only the BTHome and Xiaomi support the native HA Xiaomi Integration, for the others use the Custom Component Passive BLE.

Supports bindkey beacon encryption.

Advertising formats.

Test program of used Bluetooth Advertising formats provided by Ircama.

Only the BTHome and Xiaomi support the native HA Xiaomi Integration, for the others use the Custom Component Passive BLE. Supports bindkey beacon encryption.

atc1441 format:

UUID 0x181A - size 16 (temperature in 0.1%, humidity in 1%): atc1441 format

Custom format (all data little-endian):

UUID 0x181A - size 19: Custom extended format in 0.01 units (all data little-endian):

uint8_t     size;   // = 18
uint8_t     uid;    // = 0x16, 16-bit UUID
uint16_t    UUID;   // = 0x181A, GATT Service 0x181A Environmental Sensing
uint8_t     MAC[6]; // [0] - lo, .. [6] - hi digits
int16_t     temperature;    // x 0.01 degree
uint16_t    humidity;       // x 0.01 %
uint16_t    battery_mv;     // mV
uint8_t     battery_level;  // 0..100 %
uint8_t     counter;        // measurement count
uint8_t     flags;  // GPIO_TRG pin (marking "reset" on circuit board) flags: 
                    // bit0: Reed Switch, input
                    // bit1: GPIO_TRG pin output value (pull Up/Down)
                    // bit2: Output GPIO_TRG pin is controlled according to the set parameters
                    // bit3: Temperature trigger event
                    // bit4: Humidity trigger event

'BTHome' format

The 'BTHome' format

Encrypted beacon formats (uses bindkey):

Xiaomi Battery Charge

  1. UUID 0xFE95 - 0x0A: Xiaomi - battery charge level 0..100%, battery voltage in mV

Xiaomi Temperature & Humidity

  1. UUID 0xFE95 - 0x0D: Xiaomi - temperature x0.1C, humidity x0.1%

Xiaomi Encrypted (bindkey enable)

  1. UUID 0xFE95 - 0x0A, 0x04, 0x06 Xiaomi - battery charge level 0..100%, temperature x0.1C, humidity x0.1% (All data are averaged over a period of 16 measurements)

Bluetooth Connection Mode

  • Primary Service - Environmental Sensing Service (0x181A):
  • Characteristic UUID 0x2A1F - Notify temperature x0.1C
  • Characteristic UUID 0x2A6E - Notify temperature x0.01C
  • Characteristic UUID 0x2A6F - Notify about humidity x0.01%
  • Primary Service - Battery Service (0x180F):
  • Characteristic UUID 0x2A19 - Notify the battery charge level 0..99%
  • Primary Service (0x1F10):
  • Characteristic UUID 0x1F1F - Notify, frame id 0x33 (configuring or making a request): temperature x0.01C, humidity x0.01%, battery charge level 0..100%, battery voltage in mV, GPIO-pin flags and triggers.

Temperature or humidity trigger (GPIO PA5 LYWSD03MMC label on the "reset" pin)

Xiaomi LYWSD03MMC has a PCB soldering test point. Available without disassembling the case and marked "Reset". Use as a trigger output with adjustable temperature and / or humidity hysteresis. Hysteresis and thresholds are set in TelinkMiFlasher.html. The output status is displayed in the advertising package.

trg_menu

trg_grf

Hysteresis:

  • =0 off,
  • if less than zero - activation on decrease,
  • if more than zero - activation on excess

Setting the pin to "1" or "0" works if both hysteresis are set to zero (TRG off).

OnOff

ESP01Relay

Trigger and reed switch status receiver on JDY-10 module ($1).

Reed switch or button functions

For CGG1, MHO_C401, CGDK2, MJWSD05MMC, a button on the case is used.

It is possible to solder a reed switch on the LYWSD03MMC board to the pins marked "P8" (GPIO PA6) and GND.

The button on the body can turn the light on and off when creating a scenario in an external program...

The state of the reed switch or button is transferred to the advertising packet and events are sent in the "Switch" and "Ccounter" modes.

Setting the "Connect" option has several functions:

  1. Short press for 80 seconds turns on the ability to connect with a device in BLE 4.2 format
  2. Long press toggles temperature display to C or F.
  3. Holding more than 20 seconds will reset the device settings to default.

Interface for receiving and displaying data on the LCD.

  • LCD shows:
  • Big number: -99.5..1999.5
  • Small number: -9..99
  • Smiley, battery, degrees
  • Setting the display time limit in sec

ShowData

The USB-COM adapter writes the firmware in explorer. Web version.

  • Connect only TX-SWS and GND wires.

USBCOMFlashTx.html

USBCOMFlashTxHtml

Chipset LYWSD03MMC HW:B1.4

  • TLSR8251F512ET24 (TLSR8258 in 24-pin TQFN). SoC: TC32 32-bit MCU 48Mhz, 64 KiB SRAM, 512 KiB Flash (GD25LE40C), Bluetooth 5.0: Mesh, 6LoWPAN, Zigbee, RF4CE, HomeKit, Long Range, Operating temperature: -40°C to +85°C, Power supply: 1.8V to 3.6V.
  • SHTV3 sensor. Measurement range: Temperature -40°C to +125°C, Humidity 0 to 100 %RH. Power supply: 1.8V to 3.6V
  • IST3055NA0 LCD controller

LYWSD03MMC B1.4 BoardPinout

TabPins

For LYWSD03MMC, the HW version is determined by the display and sensor addresses on I2C:

HW LCD I2C addr SHTxxx I2C addr Note
B1.4 0x3C 0x70 (SHTC3)  
B1.5 UART 0x70 (SHTC3)  
B1.6 UART 0x44 (SHT4x)  
B1.7 0x3C 0x44 (SHT4x) Test original string HW
B1.9 0x3E 0x44 (SHT4x)  
B2.0 0x3C 0x44 (SHT4x) Test original string HW

Version 1.7 or 2.0 is determined at first run by reading the HW line written in Flash. Display matrices or controllers are different for all versions, except B1.7 = B2.0.

Building the firmware

Windows:

  1. Go to wiki.telink-semi.cn and get the IDE for TLSR8 Chips.
  2. Install the IDE and import the 'ATC_MiThermometer' project
  3. Compile the project

Ubuntu:

  git clone https://github.com/pvvx/ATC_MiThermometer.git
  cd ATC_MiThermometer
  make

Related Work

ATC_MiThermometer is based on the original work of @atc1441, who developed the initial custom firmware version and the web-based OTA flasher (Source).

Resources & Links

CJMCU-2557 BQ25570

CJMCU-2557

Control function ID when connected

Primary Service UUID 0x1F10, Characteristic UUID 0x1F1F

ID Command
0x01 Get/Set device name
0x02 Get address of internal devices
0x03 I2C scan
0x04 I2C Universal TRansaction (UTR)
0x10 Get/Set MAC
0x11 Get/Set Mi key: DevNameID
0x12 Get/Set Mi keys: Token & Bind
0x15 Get all Mi keys
0x16 Restore prev mi token & bindkeys
0x17 Delete all Mi keys
0x18 Get/set binkey in EEP
0x20 Get/Set comfort parameters
0x22 Get/Set show LCD ext.data
0x23 Get/Set Time
0x24 Get/set adjust time clock delta
0x33 Start/Stop notify measures in connection mode
0x35 Read memory measures
0x36 Clear memory measures
0x44 Get/Set TRG config
0x45 Set TRG output pin
0x4A Get/Set TRG data (not save to Flash)
0x55 Get/Set device config
0x56 Set default device config
0x5A Get/Set device config (not save to Flash)
0x60 Get/Set LCD buffer
0x61 Start/Stop notify LCD buffer
0x70 Set PinCode
0x71 Request Mtu Size Exchange
0x72 Set Reboot on disconnect
0x73 Extension BigOTA (MJWSD05MMC)
0xDD Reset LE Long Range mode

foto