DiSlord/NanoVNA-D

Issues

• edelay display and recalled sxp file

  #95 opened a month ago by owenduffy
  6

• Screen frequency readout is wrong when using sweep command via UART

  #96 opened a month ago by la3pna
  1

• NanoVNA command file extension (.cmd)

  #97 opened a month ago by owenduffy
  0

• v1.2.40 cannot read the CAL files written by the previous version(s).

  #94 opened 4 months ago by theo222
  1

• NanoVNA-H problem with latest release v1.2.29

  #93 opened 4 months ago by vladin79
  2

• A very minor issue regarding version screen title.

  #72 opened 5 months ago by iTrooper5118
  0

• Artefacts when capturing the screen

  #41 opened 5 months ago by Ho-Ro
  2

• NanoVNA-H

  #92 opened 5 months ago by TimBastress
  2

• OT. Paypal declines my donations as a thank you.

  #77 opened 5 months ago by salawalas
  1

• unable to reprograme nanovna-h

  #59 opened 5 months ago by bendelathouwer
  2

• Buggy firmware when compiling with GCC-ARM version 12 - ok with GCC-ARM version 8

  #65 opened 5 months ago by Ho-Ro
  4

• How to Achieve Successful Serial Communication Between Arduino and NanoVNA

  #90 opened 5 months ago by orhanapaydin
  10

• What happened to 1.2.27?

  #91 opened 5 months ago by Sarah-C
  0

• Enhancement: allow specification of DC resistance of calibration LOAD

  #85 opened 7 months ago by owenduffy
  27

• Enhancement: capturetiff command

  #89 opened 6 months ago by owenduffy
  1

• Missing prompt after pause command when using uart interface

  #88 opened 6 months ago by owenduffy
  7

• Raw s21 phase at low frequencies

  #81 opened 7 months ago by owenduffy
  8

• A bug due to an unknown conflict with all versions of NanoVNA-Saver

  #87 opened 7 months ago by Ghaz75
  0

• Enhancement: one touch PAUSE/RESUME and one touch SCREENSHOT

  #84 opened 7 months ago by owenduffy
  4

• Please include an Intel hex format file in the release

  #40 opened 7 months ago by owenduffy
  3

• Erase Not progressing using dfu-util on NanoVNA-H v3.4

  #83 opened 7 months ago by arcreigh
  1

• Series through measurement of a known 200 ohm resistor yields poor result

  #82 opened 7 months ago by owenduffy
  10

• e-delay for s11, s21

  #80 opened 9 months ago by owenduffy
  7

• Error in formatting display data for measure Xtal

  #78 opened 9 months ago by Robyrob
  1

• Data smooth option not saved

  #56 opened a year ago by OneOfEleven
  1

• Feature request: Screen OFF serial command

  #74 opened a year ago by sbridger
  4

• Reading folder support on SD card -- good for organizing various calibrations

  #76 opened a year ago by maelh
  1

• NanoVNA-H4 will not turn on after loading 1.2.20

  #75 opened a year ago by pcpackrat
  1

• Other ways to support you project

  #73 opened a year ago by Sonic0
  4

• Phase not unwrapped before group delay is calculated

  #71 opened a year ago by roseengineering
  0

• Referance value when measuring S21 logMag

  #67 opened a year ago by babak777
  1

• Lower Start Frequency?

  #66 opened a year ago by Moonman0922
  1

• Unable to read .cal files on v1.2.20: "Format err"

  #68 opened a year ago by beaugunderson
  9

• Documentation for Build and Flash firmware is not correct - no reference to -H4 versions

  #69 opened a year ago by Ho-Ro
  0

• No indicator NanoVNA-H Battery

  #62 opened 2 years ago by AxxiMator
  2

• Bug in NanoVNA firmware - XTAL calculations

  #60 opened 2 years ago by Ho-Ro
  5

• Cable length measurement v1.2.22

  #63 opened 2 years ago by AxxiMator
  4

• Wrong formula for Q calculation in XTAL-SERIES

  #58 opened 2 years ago by orestesmas
  1

• Oopsie.. LiteVNA64 flashing

  #57 opened 2 years ago by hvegh
  6

• Possible problem in interpolation of calibration data - H4 - v.1.2.20

  #55 opened 2 years ago by owenduffy
  1

• Provide a command line option to build FW for the MS hardware variant.

  #54 opened 2 years ago by Ho-Ro
  14

• make flash fails

  #49 opened 2 years ago by n3xus1
  3

• NanoVNA-H - wrong text formatting of bottom line

  #52 opened 2 years ago by Ho-Ro
  1

• Paused NanoVNA stops at random frequency of sweep range

  #50 opened 2 years ago by Ho-Ro
  1

• Feature request: allow also 100 points (and 400 for H4 version)

  #37 opened 2 years ago by Ho-Ro
  6

• Confused about what version my NanoVNA is, and the README.md doesn't help....

  #39 opened 2 years ago by frohro
  1

• doc: Please add `dfu-util` cmd in README.md for Linux users

  #35 opened 2 years ago by KJ7NLL
  1

• S11 impedance changed with V1.2?

  #43 opened 2 years ago by errolt
  2

• Please update README.md

  #36 opened 2 years ago by Ho-Ro
  1

• Message "too many arguments, max 4" disturbs NanoVNASaver.

  #34 opened 3 years ago by Ho-Ro
  2