flightmonitor_MQTTtoHA

Introduction

The objective of this project is to display in Home Assistant some basic information from a system running an ADS-B receiver (dump1090-fa) that feeds servers Fligtradar24 and/or FlightAware. The bash script collects information and publish JSON MQTT messages. To ease the integration with Home Assistant, MQTT discovery messages declaring all sensors supported by the script are also published when the script/service starts. Below is a screenshot of a Home Assistant tab on which are dislayed the sensors values handled by the script (titles, weblinks and history graphs were added manually).

Installation

The script has been written with the assumption of a standard installation of FlightAware and Fligtradar24 programs, according to:

this page for FlightAware.
- In addition, piaware has been configured with receiver type set to 'beast' with the command: sudo piaware-config receiver-type beast.
this page for Flightradar24 (download and run bach script install_fr24_rpi.sh)

The script is a bash script with few dependencies: bc, jq, curl and mosquitto-clients. If not already on your machine, they can be installed by: sudo apt-get install bc jq curl mosquitto-clients

Installation steps:

Clone this repository or copy/download the scripts on the Rapsberry Pi running ADS-B receiver (dump1090-fa) and the feeders (fr24feed and/or piaware)
Edit the script file and set the values according to your configuration:

configuration of the MQTT broker: IP address, port, username and password (if needed)
configuration of the topics where are published the messages. For instance, if you do not use fr24feed, set fr24feed_subtopic to an empty string (fr24feed_topic="") or comment the line ( #fr24feed_subtopic="fr24feed").
configuration of Home Assistant:
- the topic prefix for discovery (by default discovery_prefix="homeassistant" as mentionned here)
- a suffix (for instance the machine nickname "_RPi4-Kitchen") that is appended to the unique identifier of the sensors (in case the script runs on several machines connected to the same instance of Home Assistant)
- use_device=0 or use_device=1. If use_device is equal to 1, the data associated with a source (i.e. fr24feed, dump1090-fa or piaware) are declared as entities linked to a device in Home Assistant. The device name is equal to the MQTT sub-topic appended with the unique_id_suffix. This option eases the integration in Home Assistant: when the device is selected in the 'Configuration' menu, an entity-card with all linked entities can be directly added to one of your panel. A screnshot is displayed below (with the parameters dump1090_subtopic="dump1090" and unique_id_suffix="_OdroidXU4"):
configuration of the execution of the script
- pub_discovery="yes" to publish the MQTT discovery messages to Home Assistant at the begining of the execution of the script, pub_discovery="no" not to publish them
- run_mode="loop" to publish the status messages periodically, run_mode="once" to publish them once and exit, run_mode="no" not to publish them
- update_rate=60 which define the delay between the status messages (with run_mode="loop")
The three above parameters can be overwritten by launching the script with the arguments
- -d [yes|no] to overwrite pub_discovery
- -r [loop|once|no] to overwrite run_mode
- -t nn to overwrite update_rate

Launch the script flightmonitor_MQTTtoHA.sh and check new entities are available in Home Assistant

bash flightmonitor_MQTTtoHA.sh
or ./flightmonitor_MQTTtoHA.sh in case you previously set the execution permission to the file (chmod a+x flightmonitor_MQTTtoHA.sh)

When the above step is successful, you can run the install script: sudo bash install_service.sh It will create a file flightmonitor_MQTTtoHA.service which is copied to /etc/systemd/system directory and launch the service. The status of the service is displayed at the end of the install script. By default, the service is configured to send status messages every minute. This value can be changed by running the install_service.sh script with argument -t followed by the value in seconds. For example, for an update every 5 minutes: sudo bash install_service.sh -t 300.

The status of the service is reflected in Home Assistant: sensors will be marked "unavailable" if the service is stopped (or when the script in "loop" mode is stopped with Ctrl+C)

active	stopped

Principles

dump1090-fa

The parameters of the MQTT message are derived from the JSON file /run/dump1090-fa/aircraft.json (which is also used to display the aircrafts on the map @ http://127.0.0.1:8080). For example:

{
    "problem":"OFF",
    "total_aircraft":"14",
    "aircraft_with_positions":"11"
}

In Home Assistant,

the fields problem is declared as binary sensors with device class "problem".
the fields total_aircraft and aircraft_with_positions are declared as sensors.

fr24feed

The parameters of the MQTT message are derived from the JSON file http://127.0.0.1:8754/monitor.json (which is also used for status available @ http://127.0.01:8754). For example:

{
    "problem":"OFF",
    "connection":"ON",
    "mlat_problem":"OFF",
    "lastACsent":"1",
    "numACtracked":"14",
    "numACuploaded":"9"
}

In Home Assistant,

the fields problem and mlat_problem are declared as binary sensors with device class "problem".
the field connection is declared as binary sensors with device class "connectivity".
the fields lastACsent, numACtracked and numACuploaded are declared as sensors.

piaware

The parameters of the MQTT message are derived from the output of the command piaware-status. For example:

{
    "piaware_problem":"OFF",
    "faup1090_problem":"OFF",
    "faup978_problem":"ON",
    "mlat_problem":"OFF",
    "dump1090_problem":"OFF",
    "faup1090dump1090_connection":"ON",
    "piawareserver_connection":"ON",
    "data3005_problem":"OFF"
}

In Home Assistant,

the fields piaware_problem, faup1090_problem, faup978_problem, mlat_problem, dump1090_problem and data3005_problem are declared as binary sensors with device class "problem".
the fields faup1090dump1090_connection and piawareserver_connection are declared as binary sensors with device class "connectivity".

Home Assistant

When the script or service is laucnhed, the MQTT discovery messages are published.

Problems and investigations

This script has been tested on

a Raspberry Pi, model 2+ running RaspiOS distribution 2021-05-07-raspios-buster-armhf-lite
an Odroid-XU4 running DietPi distribution DietPi_OdroidXU4-ARMv7-Buster

In case it does not work properly on your system, below is a list of suggestions to investigate the issues. When debugging, it is recommanded to lower the value of the update_rate variable to few seconds (e.g.update_rate=5).

After each change to the script, restart the service sudo systemctl restart flightmonitor_MQTTtoHA
After each change to the service file (/etc/systemd/system/flightmonitor_MQTTtoHA.service)
- relaunch systemd: sudo systemctl daemon-reload
- restart the service: sudo systemctl restart flightmonitor_MQTTtoHA

Check the file flightmonitor_MQTTtoHA.service can be found in /etc/systemsd/system directory
Check service status: sudo systemctl status flightmonitor_MQTTtoHA
Check MQTT messages are publish in the topics configured by the variables at the begining of the script. For instance assuming mqtt_topic_prefix="flightmonitor" and dump1090_subtopic="dump1090" and that the MQTT borker runs on the same machine: mosquitto_sub -h 127.0.0.1 -p 1883 -t flightmonitor/dump1090.
Check MQTT discovery messages are published when the service start/re-start. For instance: mosquitto_sub -h 127.0.0.1 -p 1883 -t homeassistant/# -v

EricG78/flightmonitor_MQTTtoHA

flightmonitor_MQTTtoHA

Introduction

Installation

Installation steps:

Principles

dump1090-fa

fr24feed

piaware

Home Assistant

Problems and investigations