/core

grblHAL core code and master Wiki

Primary LanguageCOtherNOASSERTION

grblHAL

grblHAL has many extensions that may cause issues with some senders. As a workaround for these a compile time option has been added that disables extensions selectively.

IMPORTANT! grblHAL defaults to normally closed (NC) switches for inputs, if none are connected when testing it is likely that the controller will start in alarm mode.
Temporarily short the Reset, E-Stop and Safety Door4 inputs to ground or invert the corresponding inputs by setting $14=73 to avoid that.
Please check out this Wiki page for additional important information.

Windows users may try ioSender, binary releases can be found here. It has been written to complement grblHAL and has features such as proper keyboard jogging, advanced probing, automatic reconfiguration of DRO display for up to 6 axes, lathe mode including conversational G-Code generation, 3D rendering, macro support etc. etc.


Latest build date is 20220210, see the changelog for details.
NOTE: A settings reset will be performed on an update for versions earlier than 20211122. Backup and restore of settings is recommended.
IMPORTANT! A new setting has been introduced for ganged axes motors in version 20211121.
I have only bench tested this for a couple of drivers, correct function should be verified after updating by those who have more than three motors configured.
More details in the changelog.


Updated for lates core changes. NOTE: Arduino drivers has now been converted to Arduino libraries, installation and compilation procedure has been changed!


grblHAL is a no-compromise, high performance, low cost alternative to parallel-port-based motion control for CNC milling and is based on the Arduino version of grbl. It is mainly aimed at ARM processors (or other 32-bit MCUs) with ample amounts of RAM and flash (compared to AVR 328p) and requires a hardware driver to be functional. Currently drivers are available for more than 15 different processors/processor families all of which share the same core codebase.

grblHAL has an open architecture allowing plugins to extend functionality. User made plugins can be added to grblHAL without changing a single file in the source1, and allows for a wide range extensions to be added. New M-codes can be added, space for plugin specific settings can be allocated, events can be subscribed to etc. etc.
Adding code to drive an ATC, extra outputs or even adding a UI2 has never been easier. You can even add your own driver if you feel so inclined.

HAL = Hardware Abstraction Layer

The controller is written in highly optimized C utilizing features of the supported processors to achieve precise timing and asynchronous operation. It is able to maintain up to 300kHz3 of stable, jitter free control pulses.

It accepts standards-compliant g-code and has been tested with the output of several CAM tools with no problems. Arcs, circles and helical motion are fully supported, as well as, all other primary g-code commands. Macro functions, variables, and some canned cycles are not supported, but we think GUIs can do a much better job at translating them into straight g-code anyhow.

Grbl includes full acceleration management with look ahead. That means the controller will look up motions into the future and plan its velocities ahead to deliver smooth acceleration and jerk-free cornering.

This is a port/rewrite of grbl 1.1f and should be compatible with GCode senders compliant with the specifications for that version. It should be possible to change default compile-time configurations if problems arise, eg. the default serial buffer sizes has been increased in some of the drivers provided.

1 This feature is only to be used for private plugins, if shared then a single call must be added to the driver code of the target processors.
2 I do not usually recommend doing this, and I will not accept pull requests for any. However I may add a link to the github repository for any that might be made.
3 Driver/processor dependent.
4 Not enabled by default if building from source, but may be enabled in prebuilt firmware.


List of Supported G-Codes:
  - Non-Modal Commands: G4, G10L2, G10L20, G28, G30, G28.1, G30.1, G53, G92, G92.1
  - Additional Non-Modal Commands: G10L1*, G10L10*, G10L11*
  - Motion Modes: G0, G1, G2, G3, G5, G38.2, G38.3, G38.4, G38.5, G80, G33*
  - Canned cycles: G73, G81, G82, G83, G85, G86, G89, G98, G99
  - Repetitive cycles: G76*
  - Feed Rate Modes: G93, G94, G95*, G96*, G97*
  - Unit Modes: G20, G21
  - Scaling: G50, G51
  - Lathe modes: G7*, G8*
  - Distance Modes: G90, G91
  - Arc IJK Distance Modes: G91.1
  - Plane Select Modes: G17, G18, G19
  - Tool Length Offset Modes: G43*, G43.1, G43.2*, G49
  - Cutter Compensation Modes: G40
  - Coordinate System Modes: G54, G55, G56, G57, G58, G59, G59.1, G59.2, G59.3
  - Control Modes: G61
  - Program Flow: M0, M1, M2, M30, M60
  - Coolant Control: M7, M8, M9
  - Spindle Control: M3, M4, M5
  - Tool Change: M6* (Two modes possible: manual** - supports jogging, ATC), M61
  - Switches: M48, M49, M50, M51, M53
  - Output control***: M62, M63, M64, M65, M66, M67, M68
  - Valid Non-Command Words: A*, B*, C*, F, H*, I, J, K, L, N, P, Q*, R, S, T, X, Y, Z

  *  driver/configuration dependent.
  ** requires compatible GCode sender due to protocol extensions, new state and RT command.
  *** number of outputs supported dependent on driver implementation.

Some plugins implements additional M-codes.


2022-02-10