Issues
- 2
Is my dog dead?
#266 opened by OldSurferDude - 12
Unable find App on Google Play
#249 opened by ralphxyz - 1
Android touch screen controls, multimeter
#265 opened by Mariovilb - 2
Introducing duty cycle to the Square waveform
#264 opened by mmehari - 9
Unable to download software to raspberry pi
#261 opened by lcarletti88 - 3
Device Not Recognized on Windows
#262 opened by jtleniger - 3
Extending Labrador vendor requests
#260 opened by mmehari - 2
- 1
Debugging the firmware
#257 opened by mmehari - 1
Howto manual firmware recovery?
#258 opened by brummer-simon - 0
Updated PKGBUILD for Arch Linux
#234 opened by bsdice - 5
logic analyzer - I2C decoder
#237 opened by abondis - 2
- 2
Waveform generation clock settings
#255 opened by dbsamithey - 2
name space android studio
#254 opened by shaynababe - 2
Couple Hardware questions
#253 opened by MATRIX7878 - 1
Device not detected!
#252 opened by MadJalapeno - 4
[FR] Documentation to increase V in
#251 opened by slepiavka - 2
Curve tracer
#250 opened by david0rk - 1
Resolution 1024x600 for 7 inch display with Rpi 4
#248 opened by johndoc - 3
Device not Detected Windows
#247 opened by hjrjacquez - 2
Building with avr-gcc
#245 opened by dbsamithey - 2
Logic Analyzing
#246 opened by MATRIX7878 - 1
Recording - where is this?
#244 opened by rvjohnson70 - 1
Labrador Development Documentation
#243 opened by damercer - 2
Spectrum mode waveform breaks
#241 opened by dbsamithey - 0
- 1
- 1
UART output
#239 opened by WilliamWintSBU - 1
Desktop_Interface build
#238 opened by dbsamithey - 2
Unable to save data from multimeter mode
#236 opened by David-1258 - 3
- 1
Oscilloscope range clipping
#232 opened by MrDerples - 2
Write Calibration instructions on the wiki
#230 opened by chistogo - 1
- 3
EspoTek on Debian 10.13 with Lenovo-t520
#228 opened by MoeMaravilla - 1
Website TLS certificat expiry
#229 opened by jrddunbr - 2
Device will only measure 3 volts
#226 opened by JvilleJTW - 5
Connecting to Windows 10 and Mac OS 11 causes Labrador to crash in background
#227 opened by akaBryanB - 6
EspoTek Labrador.Exe Bad Image
#225 opened by JasonAlcor - 1
- 1
Segmentation fault at exit
#223 opened by jfbauer432 - 3
Logic analyzer logging
#222 opened by david0rk - 1
ESPOTEK Labrador: "Last usb device you connected to has malfunctioned and Windows does not recognize it"
#221 opened by miked9746 - 0
Raspbian 64-bit support
#219 opened by EspoTek - 8
new board, after calibrate channel 1 always read around 1.667 volts and multimeter reads new 9v Alkaline at 10.1v
#215 opened by Mclute0 - 1
- 2
Single shot trigger not working on windows 10
#217 opened by drmolix - 1
Espo tek Labrador Software installation failure
#216 opened by nelkhal10 - 1
Feature request: builtin documentation browser
#214 opened by marclava