Doesn't boot on OrangePi Zero 2
osscombat opened this issue · 3 comments
osscombat commented
Hi,
Just gave it a try on a new OPiZ2 recently - it doesn't work as expected. No IP-address is being requested, no signal over mHDMI, network LEDs are blinking though.
Note: RPI4 image boots fine even on RPi3, but probably this board is too weak, the sound is jerking badly in the browser.
F1ATB commented
RPI3 is too weak.
OPIZ2, may be an issue with the SD card. Currently Remote SDR version 5
image is running correctly on OPIZ2. I have good return I have one running
just in front of me.
73
F1ATB
Le mar. 21 mars 2023 à 15:49, osscombat ***@***.***> a écrit :
… Hi,
Just gave it a try on a new OPiZ2 recently - it doesn't work as expected.
No IP-address is being requested, no signal over mHDMI, network LEDs are
blinking though.
Note: RPI4 image boots fine even on RPi3, but probably this board is too
weak, the sound is jerking badly in the browser.
—
Reply to this email directly, view it on GitHub
<#32>, or unsubscribe
<https://github.com/notifications/unsubscribe-auth/ACN7K5OD7T3JBONW5DKBQZLW5G5WLANCNFSM6AAAAAAWCRUPCY>
.
You are receiving this because you are subscribed to this thread.Message
ID: ***@***.***>
--
André Buhart
F1ATB
https://f1atb.fr
https://sea-seek.com
osscombat commented
It's not the sdcard, I have tried two different. Official 3.0.6 debian
image boots fine, will try the manual install.
вт, 21 мар. 2023 г., 19:27 F1ATB ***@***.***>:
… RPI3 is too weak.
OPIZ2, may be an issue with the SD card. Currently Remote SDR version 5
image is running correctly on OPIZ2. I have good return I have one running
just in front of me.
73
F1ATB
Le mar. 21 mars 2023 à 15:49, osscombat ***@***.***> a écrit :
> Hi,
> Just gave it a try on a new OPiZ2 recently - it doesn't work as expected.
> No IP-address is being requested, no signal over mHDMI, network LEDs are
> blinking though.
>
> Note: RPI4 image boots fine even on RPi3, but probably this board is too
> weak, the sound is jerking badly in the browser.
>
> —
> Reply to this email directly, view it on GitHub
> <#32>, or unsubscribe
> <
https://github.com/notifications/unsubscribe-auth/ACN7K5OD7T3JBONW5DKBQZLW5G5WLANCNFSM6AAAAAAWCRUPCY
>
> .
> You are receiving this because you are subscribed to this thread.Message
> ID: ***@***.***>
>
--
André Buhart
F1ATB
https://f1atb.fr
https://sea-seek.com
—
Reply to this email directly, view it on GitHub
<#32 (comment)>,
or unsubscribe
<https://github.com/notifications/unsubscribe-auth/AHJ2YGOE72SNIYQCZ7U4K6LW5HJFTANCNFSM6AAAAAAWCRUPCY>
.
You are receiving this because you authored the thread.Message ID:
***@***.***>
dona76 commented
I encountered the same problem: partial boot with the armbian logo on the hdmi output then nothing but the fixed cursor.
I replaced the Intenso 16GB microSD card with a Sandisk 32GB and it works. Both are marked: UHS I, V30, Class 10, 4k camera, UHS class 30MB/s...
See : http://www.orangepi.org/orangepiwiki/index.php/Orange_Pi_Zero_2#Prepare_the_necessary_accessories