FarmBot/farmbot-arduino-firmware

Issues

• Change parameter units

  #111 opened 5 years ago by gabrielburnworth
  0

• Soil Moisture sensor

  #117 opened 5 years ago by ConnorRigby
  0

• NTH? Support for one more axis? A?

  #164 opened 3 years ago by burk80
  1

• How to configure the code if i replace the RAMPs 1.4 with Arduino Mega by MKS GEN 1.4 ?

  #163 opened 3 years ago by alkhlama
  5

• How to use Steppers without Encoders?

  #162 opened 3 years ago by TehseenHasan
  1

• [FEATURE REQUEST] Repository for Farmbot PCBs

  #161 opened 4 years ago by darigovresearch
  3

• .

  #158 opened 4 years ago by XODDO
  0

• CommitSHA.h incorrectly formatted

  #156 opened 4 years ago by jsimmonds2
  5

• TMC2130 firmware support

  #116 opened 5 years ago by roryaronson
  0

• Arc support?

  #36 opened 9 years ago by roryaronson
  0

• Manual Control (joystick/D-pad style movements)

  #113 opened 5 years ago by roryaronson
  0

• [bug, minor] Firmware interface reports wrong dv/dt for Z-axis state

  #135 opened 5 years ago by jsimmonds2
  2

• Split Z-axis speed settings for up/down variation

  #115 opened 5 years ago by roryaronson
  0

• Calibration and Homing Improvements

  #108 opened 5 years ago by roryaronson
  1

• Add error codes to `R03`

  #110 opened 5 years ago by ConnorRigby
  1

• 75, 76, 77 missing from readme

  #105 opened 5 years ago by ConnorRigby
  1

• I2C communication

  #8 opened 5 years ago by TimEvWw
  1

• the stepper moved too slow?

  #98 opened 5 years ago by yunfan
  4

• F21/R21 broken

  #106 opened 6 years ago by ConnorRigby
  1

• Where to buy a new Farmduino?

  #102 opened 6 years ago by Agrartechnik17
  1

• Wont compile

  #99 opened 7 years ago by kierenblack
  6

• the calibration?

  #43 opened 8 years ago by innovatemaker
  11

• z-axis is moving due to its own weight

  #65 opened 8 years ago by bautze
  3

• GetCodeEnum () is always equal to CODE_UNDEFINED

  #45 opened 8 years ago by linqingfeng
  1

• 3.0.3 Version Problem

  #58 opened 8 years ago by innovatemaker
  4

• Dont work endpoint after update

  #62 opened 8 years ago by innovatemaker
  3

• Motor X2 not working

  #54 opened 8 years ago by AscendFB
  3

• Watering

  #7 opened 8 years ago by TimEvWw
  0

• Movements switch direction inadvertently

  #20 opened 8 years ago by roryaronson
  6

• Discuss error handling

  #6 opened 8 years ago by TimEvWw
  0

• Build steps have changed.

  #22 opened 8 years ago by RickCarlino
  0

• Calibration of paramaters bricks the device

  #31 opened 8 years ago by roryaronson
  2

• Z-movements don't work

  #32 opened 8 years ago by roryaronson
  4

• X2 Dont work

  #42 opened 8 years ago by innovatemaker
  6

• Support G codes in mm

  #46 opened 8 years ago by fluffy
  1

• The CurrentState::getPoint() returns the address of a local stack varaible

  #48 opened 8 years ago by fluffy
  0

• The limit switched need a pull up resistor

  #50 opened 8 years ago by fluffy
  1

• Bug reported by @fluffy on the forum

  #47 opened 8 years ago by RickCarlino
  3

• Error while performing ino build

  #38 opened 8 years ago by davetom13
  6

• Verification of Tool Mounting

  #17 opened 9 years ago by roryaronson
  9

• Arduino is going sloowwww

  #18 opened 9 years ago by roryaronson
  3

• Change this repo to 'farmbot-arduino-firmware' ??

  #28 opened 9 years ago by roryaronson
  3

• Servo Support

  #13 opened 10 years ago by twitchyliquid64
  17

• Calibration of axis length

  #5 opened 10 years ago by TimEvWw
  0