Anycubic Vyper Mods that i have done.
- All the Print Times are rough Estimates that the Ultimaker said.
- When Printing with PLA i use a Temp of 200
- When Printing with PLA+ i use a Temp of 210
- Screen Cover
- Hinges: (Layer Height: 0.1mm | Infill: 10% | Support: NO | Adhesion: NO | Print Time: 29 Mins x 2 = 58 Mins)
- Cover: (Layer Height: 0.2mm | Infill: 10% | Support: NO | Adhesion: NO | Print Time: 1 Hr 9 Mins)
- Frame: (Layer Height: 0.2mm | Infill: 10% | Support: NO | Adhesion: NO | Print Time: 2 Hr 6 Mins)
- Platform Guides - Green Guides
- Guides L/R: (Layer Height: 0.2mm | Infill: 10% | Support: NO | Adhesion: NO | Print Time: 47 Mins x 2 = 1 Hr 34 Mins)
- Data Port Cover - Green Cover
- Cover: (Layer Height: 0.2mm | Infill: 100% | Support: NO | Adhesion: NO | Print Time: 8 Mins)
- Basic Feet
- Feet: (Layer Height: 0.2mm | Infill: 20% | Support: NO | Adhesion: NO | Print Time: 29 Mins)
- Toolbox
- Box: (Layer Height: 0.3mm | Infill: 10% | Support: NO | Adhesion: NO | Print Time: 6 Hr 41 Mins)
- Box wo Bottom: (Layer Height: 0.3mm | Infill: 10% | Support: NO | Adhesion: NO | Print Time: 3 Hr 47 Mins)
- Toolbox Handle Cover
- Cover: (Layer Height: 0.2mm | Infill: 0% | Support: NO | Adhesion: NO | Print Time: 15 Mins)
- PTFE Guide Clip
- Clips: (Layer Height: 0.2mm | Infill: 10% | Support: NO | Adhesion: NO | Print Time: 4 Mins x 4 = 16 Mins)
- 45 Degree Runout
- Bracket: (Layer Height: 0.2mm | Infill: 15% | Support: YES | Adhesion: NO | Print Time: 58 Mins)
- Filament Guide
- Guide: (Layer Height: 0.2mm | Infill: 20% | Support: YES | Adhesion: NO | Print Time: 42 Mins)
- Top Mount Spool Holder
- Holder: (Layer Height: 0.2mm | Infill: 20% | Support: NO | Adhesion: NO | Print Time: 3 Hr 26 Mins)
- Mounted Drip Tray & Trash Bin
- Bin: (Layer Height: 0.2mm | Infill: 25% | Support: NO | Adhesion: NO | Print Time: 5 Hr 54 Mins)
- Legs: (Layer Height: 0.2mm | Infill: 25% | Support: NO | Adhesion: NO | Print Time: 41 Mins)
- Kobra V-Slot Cover
- Screw Cover: (Layer Height: 0.2mm | Infill: 0% | Support: NO | Adhesion: NO | Print Time: 3 Mins x 4) - 2 on Left Side, 2 on Right Side,
- Cover 35mm: (Layer Height: 0.2mm | Infill: 0% | Support: NO | Adhesion: NO | Print Time: 2 Mins x 2 = 4 Mins) - 2 on Left Side Top Before Drip Tray Legs
- Cover 50mm: (Layer Height: 0.2mm | Infill: 0% | Support: NO | Adhesion: NO | Print Time: 3 Mins x 2 = 6 Mins) - 2 on Bottom Tension Track
- Cover 120mm: (Layer Height: 0.2mm | Infill: 0% | Support: NO | Adhesion: NO | Print Time: 6 Mins x 2 = 12 Mins) - 2 on Left Side Top In-Between Drip Tray Legs
- Cover 130mm: (Layer Height: 0.2mm | Infill: 0% | Support: NO | Adhesion: NO | Print Time: 7 Mins x 2 = 14 Mins) - 2 on Right Side Front Goes Slightly under Screen Mounts
- Cover 135mm: (Layer Height: 0.2mm | Infill: 0% | Support: NO | Adhesion: NO | Print Time: 7 Mins x 2 = 14 Mins) - 2 on Top Printer
- Cover 150mm: (Layer Height: 0.2mm | Infill: 0% | Support: NO | Adhesion: NO | Print Time: 8 Mins x 10 = 1 Hr 20 Mins) - 4 on Right/Left Top Back, 4 on Right/Left Side Back, & 2 on Bottom Tension Track
- Cover 160mm: (Layer Height: 0.2mm | Infill: 0% | Support: NO | Adhesion: NO | Print Time: 8 Mins x 4 = 32 Mins) - 2 on Left Side Front & 2 on Bottom Tension Track
- Cover 170mm: (Layer Height: 0.2mm | Infill: 0% | Support: NO | Adhesion: NO | Print Time: 9 Mins x 4 = 36 Mins) - 2 on Left Side Top & 2 on Right Side Top (NOTE: Don't use if using Mounted Drip Tray & Screen)
- Chainlink
- Follow Video Guide
- bed_cable_reinforced_redesign_REMIX: (Layer Height: 0.2mm | Infill: 25% | Support: NO | Adhesion: NO | Print Time: 49 Mins)
- small_Chainlink_Cover_V2(23): (Layer Height: 0.2mm | Infill: 25% | Support: NO | Adhesion: NO | Print Time: 43 Mins)
- small_dragchain_V2.1(23): (Layer Height: 0.2mm | Infill: 25% | Support: NO | Adhesion: NO | Print Time: 3 Hr 53 Mins)
- Widend_Chainlink_Cover_V2(26): (Layer Height: 0.2mm | Infill: 25% | Support: NO | Adhesion: NO | Print Time: 55 Mins)
- Widend_PSU_Cable_Split_V2.1(1): (Layer Height: 0.2mm | Infill: 25% | Support: NO | Adhesion: NO | Print Time: 59 Mins)
- widened_dragchain_V2.1(26): (Layer Height: 0.2mm | Infill: 25% | Support: NO | Adhesion: NO | Print Time: 4 Hr 53 Mins)
- widened_platform_chain_mount_V2(1): (Layer Height: 0.2mm | Infill: 25% | Support: YES | Adhesion: NO | Print Time: 1 Hr 45 Mins)
- Z Axis Anti Wobble/Vibration Ring
- "Print thin walls" must be activated so that it prints the upper ring
- Ring: (Layer Height: 0.2mm | Infill: 15% | Support: NO | Adhesion: NO | Print Time: 2 Mins x 2 = 4 Mins)
- Z Axis Ring
- "Print thin walls" must be activated so that it prints the upper ring
- Z_Axis_Ring_2: (Layer Height: 0.2mm | Infill: 100% | Support: NO | Adhesion: NO | Print Time: 4 Mins x 2 = 8 Mins)