Tantillus Introducing Tantillus. The portable self replicating mini printer. Please visit www.Tantillus.org for more information ** Please note these files may change without notice ** If you find mistakes or convert it to metric please file a bug report here on GitHub or even better a pull request. - Derived parts: - 4 - Triffidhunter's Printable LM8uu v3 bushings http://www.thingiverse.com/thing:16813 - One piece case (200mm x 200mm x 300mm) - 1 - Tantillus.0.2.0.stl NOTE: See image folder for exploded view of printed case. - Printed Case files: - - Printed case source: - Tantillus.0.1.1.blend Tantillus.0.1.1_ABS.blend 1 - Case top 1 1 - Case top 2 1 - Case top 3 1 - Case top 4 1 - Case middle 1 1 - Case middle 2 1 - Case middle 3 1 - Case middle 4 1 - Case bottom 1 1 - Case bottom 2 1 - Case bottom 3 1 - Case bottom 4 - Printed case connectors: - 1 - Top front connector 2 - Top side connectors 1 - Rear lower connector 1 - Rear upper connector 3 - Middle connectors 3 - Base connectors 1 - Motor mount reinforcement 4 - Upper stiffeners NOTE: Assembled and exploded view stl files are for reference only. - Axis Parts: - 1 - Bowden clamp.stl 1 - Carriage bottom.stl 1 - Carriage top.stl 1 - Endstop_holder.stl 4 - Printable-lm8uu-v3.stl 2 - XY_end_left.stl 2 - XY_end_right.stl 1 - Z_arm_1.stl 1 - Z_arm_2.stl 2 - Z-coupler.stl 1 - Z_lift.stl 1 - Z_lower_bracket.stl 1 - Z_motor_bracket.stl 1 - Z_upper_bracket.stl - Extruder: - 1 - Extruder.stl 1 - Extruder_idler.stl 1 - Extruder_motor_mount_v2.stl - Gears: - NOTE: 4mm and 5mm denote motor shaft size (use only one size) NOTE: Or use optional pulleys in Pulley folder 2 - Upper gear.stl 2 - Motor_gear_(4mm).stl or 2 - Motor_gear_(5mm).stl - Optional Pulleys - NOTE: Only use if you are NOT planning on using the above gears NOTE: Uses 267-3GT-06 belts. NOTE: #4 is for imperial nuts and grub screws, M4 is for Metric nuts and grub screws 2 - Upper_50T_pulley_(8mm)(nn).stl and 2 - Motor_40T_pulley_(4mm)(nn).stl or 2 - Motor_40T_pulley_(5mm)(nn).stl - Experimental pulleys - NOTE: There is a folder with 50 tooth motor pulleys that can be used in place of the 40T ones above. But be warned there is no access to the motor bolts and you will be required to use hex bolts or figure out some other way of tensioning them. - Extruder gears - 1 - Extruder_large.stl (normal gears 2.7:1) 1 - Extruder_small_(4mm).stl (normal gears 2.7:1) or 1 - Extruder_small_(5mm).stl (normal gears 2.7:1) - Laser cut case files: - NOTE: STL's are used to produce the DXF's and SVG's and are not for printing. All_panels.dxf All_panels.stl All_panels.svg Back.dxf Back.stl Back.svg Carriage_middle.dxf Carriage_middle.stl Carriage_middle.svg Front.dxf Front.stl Front.svg Left.dxf Left.stl Left.svg Right.dxf Right.stl Right.svg NOTE: Cutting test to confirm fit of tabs and bearings Test.dxf Test.svg test.stl NOTE: Scad file used to make DXF's from STL's (Inkscape used to convert DXF's to SVG's) V3_svg.scad - Laser cut case corners - NOTE: You may require scaling these by %1 or %2 4 - Corner_bottom.stl 1 - Corner_top_front_left.stl 1 - Corner_top_front_right.stl 1 - Corner_top_rear_left.stl 1 - Corner_top_rear_right.stl - Extras - NOTE: Not all of these are used for each machine choose wisely (LC) = Laser cut 40mm_fanmount_(LC).stl 50mm_fanmount_(LC).stl 40mm_Fan_mount_(printed case).stl Encoder_knob.stl 40mm_Fan_duct.stl Plug_adapter.stl Repraper_spool_a.stl Repraper_spool_b.stl Spool_holder.stl (Esun style spool) Spool_holder_long.stl (Makerbot spool) Spool_holder_mount.stl (Fits both Esun and Makerbot spool holder) - Source files - Tantillus.0.3.4.blend (laser cut case and all axis parts) 40mm_Fan_duct.blend All_Fanmounts.blend Extruder_gears_v2.blend Plug_adapter.blend Spool_holders.blend Tantillus_extruder.blend Tantillus_gears.blend Cable-Z_and_Printed-case-extensions.blend