/bt-speaker

A simple Bluetooth Speaker Daemon for the Raspberry Pi 3

Primary LanguageCGNU General Public License v3.0GPL-3.0

BT-Speaker

A simple Bluetooth Speaker Daemon designed for the Raspberry Pi 3.

Installation

Quick Installation for Raspbian:

sudo -i
bash <(curl -s https://raw.githubusercontent.com/lukasjapan/bt-speaker/master/install.sh)

For details refer to the comments in the install script.

Depending on your application, you might also want to send all audio to the headphone jack. This can be done by raspi-config:

Advanced Options -> Audio -> Force 3.5mm ('headphone') jack

Usage

The BT-Speaker daemon does not behave like a typical bluetooth device. Once a client disconnects, the speaker will immediately allow other clients to connect. This means that the quickest device may claim the speaker and no real bluetooth pairing occurs. The bright side of this logic is that no button for unpairing is needed.

The speakers name will default to the hostname of your Raspberry Pi. BT-Speaker does not manage this value. You are advised to change the hostname according to your needs.

Config

The default settings of BT-Speaker can be overridden in /etc/bt_speaker/config.ini.

Section Key Default Value Description
bt_speaker play_command aplay -f cd - The raw audio in CD Format (16bit little endian, 44100Hz, stereo) is piped to this command.
bt_speaker connect_command ogg123 /usr/share/sounds/freedesktop/stereo/service-login.oga Command that is called when an audio device connects to BT-Speaker
bt_speaker disconnect_command ogg123 /usr/share/sounds/freedesktop/stereo/service-logout.oga Command that is called when an audio device disconnects from BT-Speaker
bluez device_path /org/bluez/hci0 The DBUS path where BT-Speaker can find the bluetooth device
alsa mixer PCM The volume of this mixer will be set from AVRCP messages (Remote volume control)
alsa id 0 The alsa id of the mixer control
alsa cardindex 0 The alsa cardindex of the soundcard

The settings in the alsa section specify on which alsa mixer (more info here) volume changes are applied. You need to adjust these settings if you are using an external sound card.

Example of /etc/bt_speaker/config.ini:

[bt_speaker]
play_command = aplay -f cd -
connect_command = ogg123 /usr/share/sounds/freedesktop/stereo/service-login.oga
disconnect_command = ogg123 /usr/share/sounds/freedesktop/stereo/service-logout.oga

[bluez]
device_path = /org/bluez/hci0

[alsa]
id = 0
cardindex = 0
mixer = PCM

Details of Implementation

The BT-Speaker daemon has been written in Python and works with Bluez5. It talks to the Bluez daemon via the Bluez DBUS interface.

Bluetooth profiles

BT-Speaker will register itself as an A2DP capable device and route the received audio fully decoded to ALSAs aplay command.

Changes in volume are detected via messages from the AVRCP profile and are applied directly to the ALSA master volume.

Partial Bluez5 port of BT-Manager

The great BT-Manager library does (currently) only work with Bluez4. Changes in the Bluez DBUS API from version 4 to 5 were huge and fully porting BT-Manager would have been a too heavy task. So instead, I extracted all relevant parts and ported them to Bluez5 as good as I could. Documentation and probably lots of other parts there have yet to be adjusted, so refer to that code with caution.

About the audio stream

The following describes some internals of the audio stream that is transferred via bluetooth.

Format

The Light of Dawn blog describes the format very accurate:

As it turns out, the audio data is compressed with SBC codec. But I can't just use "sbcdec" tool from SBC package to decode it, as the audio data is encapsulated in A2DP packets, not naked SBC-compressed audio data. A2DP packets are RTP packets (referenced by A2DP specification, and detailed in this IETF draft) containing A2DP Media Payload. We need to extract the SBC audio data, pass it through SBC decompressor, and only then we get raw audio data that can be sent to ALSA.

Unfortunately there is no media player (or at least I didn't find any) that could handle this 'SBC in RTP' format natively. However, BT-Manager already provided a C library that takes care of the decoding process. The decoded output is raw audio data in CD format (16 bit little endian, 44100Hz, stereo) and can be piped to ALSA as mentioned in the blog.

Decoding

The C library for the decoding process is located in the codecs folder. Its functions are called via Python CFFI. BT-Speaker provides the binary for ARM already, so there is no need to compile the codec manually.

However, if you need to do so for some reason, please be aware that the Makefile has been adjusted by the following:

  1. The default PLATFORM setting has been changed to armv6
  2. The -O3 flag has been added