Pinned Repositories
3D-Gerber-Viewer
Clone of WebGerber for use by UKSC
Arduino_Dash
CS499
Code for CS499 Senior Design Project
DriverControl_tri86_ws22
This is the repo for the driver control box that came with our new motor controller.
Drivetek_MPPT
Drivetek_MPPT This code came from Cal Sol (Berkeley CA) solar car team. We at UK have the same devices, but I am unable to find our copy. We plan to change the operating values in this code. It is critical to note that Cal Sol has licensed this as GPL2. Any update that is made to this code must be shared.
flutter_dashboard
Next gen dashboard built with Flutter
LapTimer
TeensyCAN
Telemetry-GUI
This code will run on a desktop machine, and display the data the solar car sends from an rs 232 connection
USBtin
USBtin - Simple USB to CAN interface ------------------------------------ This archive contains firmware, drivers and bootloader for the USBtin project. USBtin is a simple USB to CAN interface. You find further information about USBtin on the project homepage: http://www.fischl.de/usbtin
KentuckySolarCar's Repositories
KentuckySolarCar/3D-Gerber-Viewer
Clone of WebGerber for use by UKSC
KentuckySolarCar/Telemetry-GUI
This code will run on a desktop machine, and display the data the solar car sends from an rs 232 connection
KentuckySolarCar/Drivetek_MPPT
Drivetek_MPPT This code came from Cal Sol (Berkeley CA) solar car team. We at UK have the same devices, but I am unable to find our copy. We plan to change the operating values in this code. It is critical to note that Cal Sol has licensed this as GPL2. Any update that is made to this code must be shared.
KentuckySolarCar/USBtin
USBtin - Simple USB to CAN interface ------------------------------------ This archive contains firmware, drivers and bootloader for the USBtin project. USBtin is a simple USB to CAN interface. You find further information about USBtin on the project homepage: http://www.fischl.de/usbtin
KentuckySolarCar/DriverControl_tri86_ws22
This is the repo for the driver control box that came with our new motor controller.
KentuckySolarCar/flutter_dashboard
Next gen dashboard built with Flutter
KentuckySolarCar/Arduino_Dash
KentuckySolarCar/CS499
Code for CS499 Senior Design Project
KentuckySolarCar/LapTimer
KentuckySolarCar/TeensyBottomShellReborn
The code for the Teensy-powered main driver board (Bottom Shell) for Gato VII. A rewrite of TeensyBottomShell.
KentuckySolarCar/TeensyCAN
KentuckySolarCar/.github
A description of our organization
KentuckySolarCar/7moduleCrossoverBPS
Jimmy wrote this code. It was written so we could use the 7 moduleBPS with the single moduleBPS.
KentuckySolarCar/ad-hoc_script
This script will connect to the garage wifi when it is detected. If the ssid "solarcar" can not be found the script will open a ad-hoc network
KentuckySolarCar/DriverControlBoxTRI63
This is the code downloaded from the Tritium website (http://tritium.com.au/products/legacy-products/) on September 17 2014.
KentuckySolarCar/LCD
This is the code that drives the LCD controller board
KentuckySolarCar/project-cole
This is a meta repository containing general documentation and links to all aspects of Project C.O.L.E. Miscellaneous scripts and OS configuration may also be here
KentuckySolarCar/RaspberryPi_03
Code for raspberry pi on car
KentuckySolarCar/SCAnalysis
Python package for analysis and creation of graphs relating to variable input data.
KentuckySolarCar/State-of-Charge-Estimator
Python script for adaptive estimation of State of Charge for LiFePO4 battery pack.
KentuckySolarCar/TelemetryPython_2012
code for parsing telemetry data coming from a serial port
KentuckySolarCar/Temp-Telemetry
Temporary utility to make connecting to the Pi telemetry easier.
KentuckySolarCar/TritiumMotorTester
Runs through a pre-programmed routine of motor commands and logs the resulting telemetry. Intended for bench testing of motors.
KentuckySolarCar/UKSC_Arduino_Libraries