LibreRouterOrg/board

Issues

• Change JATG pull down resistors Value

  #64 opened 5 years ago by xcancerberox
  0

• Add JTAG connector

  #49 opened 5 years ago by xcancerberox
  1

• General Silk screen check

  #62 opened 5 years ago by xcancerberox
  0

• Properly design coupled transmission lines

  #60 opened 5 years ago by spiccinini
  2

• Add a way to disconnect the power to the board through GPIO

  #61 opened 5 years ago by spiccinini
  3

• Missing holes in PCB

  #58 opened 5 years ago by xcancerberox
  6

• Improve impedance of PCIe routing

  #54 opened 5 years ago by spiccinini
  4

• Missing Core Board?

  #59 opened 5 years ago by stephen304
  2

• GPS module does not lock (signal issues)

  #31 opened 6 years ago by spiccinini
  5

• Improve Ethernet differential pair impedance and reduce series resistance

  #57 opened 5 years ago by xcancerberox
  2

• Remove SPI connection from watchdog to core board (introduced by mistake in the Eagle to Kicad migration)

  #55 opened 5 years ago by spiccinini
  1

• Add hack ethernet port

  #45 opened 5 years ago by xcancerberox
  1

• Better PoE power handling in both LAN and WAN ports

  #34 opened 5 years ago by spiccinini
  4

• Change GPS 3.3V source

  #43 opened 5 years ago by xcancerberox
  1

• Shorten GPS uart path

  #48 opened 5 years ago by xcancerberox
  1

• Internal RF cables may disconnect or shortcircuit

  #39 opened 5 years ago by spiccinini
  1

• Change PCIe1 3.3V source

  #42 opened 5 years ago by xcancerberox
  2

• Complete BOM

  #51 opened 5 years ago by xcancerberox
  7

• Add magnetics board option

  #46 opened 5 years ago by xcancerberox
  1

• Power domain isolation

  #47 opened 5 years ago by xcancerberox
  2

• Add internal header for Core9558 ethernet ports not used

  #33 opened 5 years ago by xcancerberox
  1

• Individual disable for PCIe0 and 1

  #44 opened 5 years ago by xcancerberox
  1

• Move PCIe1 device

  #41 opened 5 years ago by xcancerberox
  1

• General track and vias review

  #50 opened 5 years ago by xcancerberox
  0

• Board hangs when power cycled with serial TTL connected

  #22 opened 5 years ago by darkdrgn2k
  5

• Prototypes have fake and reused MAC addresses

  #20 opened 5 years ago by altergui
  3

• Pin connection difference between PCIe0 and PCIe1

  #37 opened 5 years ago by xcancerberox
  1

• PCB's process parameter

  #29 opened 6 years ago by chenhaimeng
  1

• LEDs for 5GHz WLAN Operation

  #16 opened 5 years ago by nicopace
  3

• Heatsinks

  #10 opened 5 years ago by nicopace
  4

• Input voltage is <= 30V

  #25 opened 5 years ago by spiccinini
  8

• PoE passthrough circuit R32 is too low

  #28 opened 5 years ago by spiccinini
  2

• PoE and PoE Passthrough overheats magnetics

  #23 opened 5 years ago by spiccinini
  7

• Improve 5.8GHz antenna's pigtails

  #26 opened 5 years ago by spiccinini
  1

• USB LED Operation

  #9 opened 7 years ago by nicopace
  1

• Status LED Operation

  #8 opened 7 years ago by nicopace
  1

• Link LED Operation

  #7 opened 7 years ago by nicopace
  3

• Dragino PoE injector does not support 1000mbps

  #27 opened 6 years ago by spiccinini
  0

• PoE is not working

  #14 opened 6 years ago by nicopace
  6

• Hardware Reset Operation: Watchdog

  #4 opened 6 years ago by nicopace
  2

• we don't have a bootloader

  #19 opened 6 years ago by dangowrt
  1

• 2.4 Ghz radio issue

  #21 opened 6 years ago by nicopace
  12

• Screen print font

  #17 opened 6 years ago by nicopace
  3

• Board Mounting

  #12 opened 6 years ago by nicopace
  2

• ANT 2 Circuit Error

  #11 opened 6 years ago by nicopace
  3

• ANT3 connector - no signal

  #13 opened 6 years ago by nicopace
  2

• PCIe mounting holes are misaligned

  #18 opened 6 years ago by nicopace
  3

• Ethernet connector wiring

  #15 opened 6 years ago by nicopace
  1

• SWRST Operation

  #5 opened 7 years ago by nicopace
  1

• GPIO Operation

  #6 opened 7 years ago by nicopace
  1