Pinned Repositories
335x-b4
335x linux4.1 for b4
aq_flight_control
Fork of Bill Nesbitt's AutoQuad Multicopter Flight Controller firmware
arduino
Educ portable version of Arduino IDE 1.8.5, with libraries special Education : for Scratch 2, specific shield, robots, Blockly@rduino
Arduino_Core_STM32
STM32 core support for Arduino
Arduino_STM32
Arduino STM32. Hardware files to support STM32 boards, on Arduino IDE 1.8.x including LeafLabs Maple and other generic STM32F103 boards
ardupilot
Emlid's port of ArduPilot for Navio/Navio+/Navio2.
autoquad
Automatically exported from code.google.com/p/autoquad
bCNC
GRBL CNC command sender, autoleveler and g-code editor
Component-Tester-V-I-Curve-Tracer
you can use Component-Tester to learn about the behavior of the components and semiconductors.
dso203
attempt to restore buildability of Wildcat's DSO203 oscilloscope firmware + bugfixes
MeKeCNC's Repositories
MeKeCNC/Component-Tester-V-I-Curve-Tracer
you can use Component-Tester to learn about the behavior of the components and semiconductors.
MeKeCNC/dso203
attempt to restore buildability of Wildcat's DSO203 oscilloscope firmware + bugfixes
MeKeCNC/bCNC
GRBL CNC command sender, autoleveler and g-code editor
MeKeCNC/betaflight
Open Source Flight Controller Firmware
MeKeCNC/BTT_SKR_13_14_14T_SD-DFU-Bootloader
This is a repository of BIGTREETECH bootloaders. The originals are stored under the bootloader_bin/backed_up_original_bootloaders/ directory. This repository also has a bootloader for the SKR E3 TURBO to fix the high pitch sound coming out of the CR10_STOCKDISPLAY it is located on the bootloder_bin/compiled_bootloader_bin/ directory.
MeKeCNC/Candle
GRBL controller application with G-Code visualizer written in Qt.
MeKeCNC/ChargePi
⚡ChargePi🔌 is an open-source Raspberry Pi 4 based ⚡Charging Point🔌 project, which supports multiple EVSEs and simple connectors🔌. A charging connector🔌 consists of a WS281x RGB 🚥 LED strip, a relay and a power meter.
MeKeCNC/Coil64
Coil64 is inductance coil calculator, that allows to calculate the single-layer and multi-layer air core inductors, the ferrite toroid inductors or chokes, planar coils on PCB etc.
MeKeCNC/core
grblHAL core code and master Wiki
MeKeCNC/ESP32Controller
ESP32-based 3D printer controller
MeKeCNC/etcher
Flash OS images to SD cards & USB drives, safely and easily.
MeKeCNC/ext-switchev-iso15118
Implementation of the ISO 15118 Communication Protocol (-2, -20, -8)
MeKeCNC/FluidNC
The next generation of motion control firmware
MeKeCNC/grbl-Mega
An open source, embedded, high performance g-code-parser and CNC milling controller written in optimized C that will run on an Arduino Mega2560
MeKeCNC/grbl-mega-1
MeKeCNC/grbl_controller_esp32
grbl controller for esp32
MeKeCNC/grbl_controller_stm32
Grbl controller running on stm32F103
MeKeCNC/Grbl_Esp32
A port of Grbl CNC Firmware for ESP32
MeKeCNC/grblcontroller
Compact android mobile application for gcode streaming and controlling a cnc machine with grbl firmware
MeKeCNC/grblLCD
Small LCD to show some status info of grbl / grblESP32 controllers
MeKeCNC/ioSender
A GCode Sender for Grbl and grblHAL written in C# (Windows only).
MeKeCNC/pi-fan-controller
Raspberry Pi fan controller.
MeKeCNC/Plugins_motor
grblHAL motor plugins
MeKeCNC/serialplot
Small and simple software for plotting data from serial port in realtime.
MeKeCNC/STM32F1xx
grblHAL driver for ST STM32F1xx (Redpill, Bluepill)
MeKeCNC/STM32F7xx
grblHAL driver for ST STM32F7xx (Nucleo-144)
MeKeCNC/STM32H7xx
grblHAL driver for ST STM32H7xx (Nucleo-144, WeAct MiniSTM32H7xx)
MeKeCNC/ti-linux-kernel-dev
vendor bsp...
MeKeCNC/UAVXArm-Source
Source code for UAVXArm and GUI etc
MeKeCNC/UTFT-ESP
UTFT with support for ESP8266 and ESP32