NabuCasa/yellow

Issues

• BOM File

  #60 opened a year ago by gui28347
  1

• Google Coral USB Stick

  #63 opened a year ago by arne182
  1

• Fan header and RGB lights

  #61 opened 2 years ago by t3hk0d3
  5

• Adjust layout to mitigate PoE shutdown issue

  #53 opened 2 years ago by agners
  1

• Fix JP2 unsecure parking position

  #56 opened 2 years ago by agners
  2

• Add more thermal vias under BD9D321EFJ chips

  #57 opened 2 years ago by randomplum
  1

• Adjust back silk screen for larger product label

  #55 opened 2 years ago by agners
  1

• Add "Made in PRC" to Silk Screen

  #52 opened 2 years ago by agners
  0

• Increase CM4 hole size for SMT stand-off nuts

  #54 opened 2 years ago by agners
  0

• CP2102N overheating issue

  #51 opened 3 years ago by agners
  1

• Dim green LED by increasing R37 to 10k

  #48 opened 3 years ago by agners
  1

• Add CM4 chip outlines to silkscreen for orientation

  #50 opened 3 years ago by agners
  0

• Add Raspberry Pi logo for orientation

  #49 opened 3 years ago by agners
  1

• Update Home Assistant and Nabu Casa logo

  #47 opened 3 years ago by agners
  3

• Add UKCA logo

  #46 opened 3 years ago by agners
  0

• Consider shifting J11 closer to MGM210P

  #45 opened 3 years ago by agners
  2

• Orientation of D26, D27, D28 and D29 not visible

  #39 opened 3 years ago by agners
  0

• Draw Heatsink outline on PCB silk screen

  #44 opened 3 years ago by agners
  0

• Adjust C85 to match Nichicon UCD1K470MNL1GS

  #40 opened 3 years ago by agners
  2

• Use FSUSB30MUX instead of FSUSB42MUX

  #42 opened 3 years ago by agners
  1

• SDA/SCL reversed on TSSOP-8 RTC footprint U25

  #43 opened 3 years ago by agners
  1

• USB D+/D- reversed

  #41 opened 3 years ago by agners
  1

• Add silk screen mentioning the input voltage/amperage

  #38 opened 3 years ago by agners
  0

• Change "USB Boot" silkscreen text

  #26 opened 3 years ago by agners
  2

• Use TE F1.1 48-LQFP USB Hub

  #37 opened 3 years ago by agners
  1

• Remove bottom holes

  #33 opened 3 years ago by agners
  0

• Add GND testpoint

  #31 opened 3 years ago by agners
  0

• Pulse Transformer T1 for PoE assembled in non-PoE variant

  #34 opened 3 years ago by agners
  1

• Check for non-PoE Ethernet plug

  #18 opened 3 years ago by agners
  1

• Replace USB-Hub U7 USB2422 with Terminus Tech FE1.1

  #28 opened 3 years ago by agners
  0

• Audio Jack feet too short

  #30 opened 3 years ago by agners
  3

• Disable LP5569 RGB LED solution/use regular Raspberry Pi LEDs

  #32 opened 3 years ago by agners
  0

• Support RTC with TSSOP-8 footprint

  #29 opened 3 years ago by agners
  0

• Replace 3xRGB LED controller LP5569 with single RGB LED LP5521

  #11 opened 3 years ago by agners
  1

• U16 not connected to GND

  #27 opened 3 years ago by agners
  0

• Use two separate footprints for CM4

  #19 opened 3 years ago by agners
  1

• Add Jumper to allow PoE class selection

  #25 opened 3 years ago by agners
  1

• Wrong pin-assignement on HDMI plug

  #24 opened 4 years ago by agners
  0

• Change package of C87/C91 from 0805 to 1206

  #21 opened 4 years ago by agners
  2

• Change package of 2.2uF/25V from 0402 to 0805

  #20 opened 4 years ago by agners
  2

• Change rating of C84/C86/C90 to 25V

  #22 opened 4 years ago by agners
  2

• Top-right corner uses different radi than the three other corners

  #23 opened 4 years ago by agners
  0

• Consider alternative MOSFET for Q1/Q2

  #13 opened 4 years ago by agners
  2

• Replace full-size HDMI with micro-HDMI

  #17 opened 4 years ago by agners
  0

• Power button not waking up module after shutdown

  #8 opened 4 years ago by agners
  2

• Redesign Switches

  #16 opened 4 years ago by agners
  0

• Replace DC-DC Buck Converter

  #12 opened 4 years ago by agners
  2

• Check USB-C Connector footprint

  #14 opened 4 years ago by agners
  0

• 3.5mm audio plug not mechanically stable

  #9 opened 4 years ago by agners
  1

• Check pull-up/down for SiLabs MGM210P radio module

  #10 opened 4 years ago by agners
  1