NeonHorizon/lipopi

Issues

• Hum noise

  #58 opened 2 years ago
  5

• Remove transparency from diagrams

  #57 opened 3 years ago
  1

• On-Off switch suggestion

  #56 opened 3 years ago
  2

• Power down while charging => immediately off

  #55 opened 4 years ago
  6

• Variant for reusing switch for soft powerdown

  #54 opened 4 years ago
  9

• Bateria Raspberry

  #53 opened 4 years ago
  0

• Connecting LBO directly to a GPIO pin

  #52 opened 4 years ago
  1

• Using other DC-DC converters

  #51 opened 5 years ago
  1

• Why is wire to GND needed?

  #50 opened 4 years ago
  11

• Is it possible to use other pins that are not UART?

  #49 opened 5 years ago
  2

• Wiring from PowerBoost 1000c to RPi 3 B

  #48 opened 5 years ago
  1

• error during run process

  #47 opened 5 years ago
  1

• step 13 not working. Pi powers off when releasing button

  #46 opened 5 years ago
  4

• Hold button 3 seconds to shut down

  #45 opened 5 years ago
  1

• Recommended code change

  #44 opened 5 years ago
  8

• Configuring the serial port without raspi-config

  #43 opened 5 years ago
  1

• EN pin on Vs instead of Bat ?

  #41 opened 6 years ago
  3

• using other pin than 14

  #40 opened 6 years ago
  1

• low battery light always on

  #39 opened 6 years ago
  2

• Auto Power on part Deux

  #38 opened 6 years ago
  26

• lipopi.py script query

  #37 opened 6 years ago
  1

• GPIO connection question

  #36 opened 6 years ago
  1

• Pinnout question

  #35 opened 6 years ago
  1

• Pi Zero W powering as soon as battery is connected

  #34 opened 6 years ago
  8

• GPIO 14 does not stay high on power up (Pi Zero W version 1.1)

  #32 opened 6 years ago
  26

• UART and USB Serial

  #31 opened 6 years ago
  1

• Tx uart share with imu

  #30 opened 6 years ago
  1

• gpio switch from pitft gpio

  #29 opened 6 years ago
  3

• RPI3 with Stretch works like the others

  #28 opened 7 years ago
  3

• LiPoPi Power Up / Power Down version low power reset

  #27 opened 7 years ago
  9

• question of software install on/off version

  #26 opened 7 years ago
  7

• Single spdt switch working

  #25 opened 7 years ago
  6

• Using a 3.3v linear regulator

  #24 opened 7 years ago
  1

• raspi-config sets enable_uart=0

  #23 opened 7 years ago
  9

• Basic Schematic Question

  #22 opened 7 years ago
  1

• Is it possible to use a ON/OFF switch with 2 positions?

  #21 opened 7 years ago
  2

• Auto Power on

  #20 opened 7 years ago
  9

• 100K resistor?

  #19 opened 7 years ago
  1

• Incompatible with RedBear IoT pHAT?

  #18 opened 7 years ago
  8

• Need to use serial to connect pc to Pi

  #17 opened 7 years ago
  6

• Shutting straight down

  #16 opened 7 years ago
  42

• Power Up path in the Power Up / Power Down version will pull GPIO 14 above 3.3 volts

  #15 opened 7 years ago
  1

• Auto Power On?

  #14 opened 8 years ago
  1

• Power up/power down version

  #13 opened 7 years ago
  1

• can't see the button in the photo

  #12 opened 8 years ago
  3

• not enough voltage on GPIO14 on pi3

  #9 opened 8 years ago
  20

• Not latching on

  #8 opened 7 years ago
  48

• How long does the battery last?

  #4 opened 8 years ago
  1

• Typos in README

  #3 opened 8 years ago
  1

• 4.2Volts on 3.3Volts GPIO

  #2 opened 8 years ago
  16