OpenSourceEBike/TSDZ2-Smart-EBike

Issues

• clear_eeprom fails with invalid address

  #163 opened a year ago by chgpalmer
  0

• Battery Display

  #162 opened 2 years ago by JasperCat123
  3

• New verison Tongsheng TSDZ2 compatibility

  #159 opened 2 years ago by Walkability
  1

• TSDZ2-ESP-32 compatibility?

  #160 opened 2 years ago by washichi
  3

• Random hangs / freezes in menu with SW102 and FW1.0.0

  #144 opened 4 years ago by palm369
  1

• motor code should include a bit (or packet count) that indicates it is receiving packets from the display...

  #122 opened 5 years ago by geeksville
  2

• Wheel speed sanity check

  #145 opened 4 years ago by iamblacklite
  2

• TMP36 vs LM35 temperature sensor

  #118 opened 5 years ago by j0bro
  2

• Weird serial output after flashing OSF to motor

  #158 opened 3 years ago by elpollodiablo
  1

• coaster brake and backpaddling

  #157 opened 3 years ago by PrivatePuffin
  1

• [Feature] Sloped temperature limit

  #156 opened 3 years ago by PrivatePuffin
  1

• Document EN:15194 Compliance

  #146 opened 4 years ago by PrivatePuffin
  3

• Implement again startup BOOST

  #123 opened 5 years ago by casainho
  0

• Possible to use this firmware and controller for hub motor

  #155 opened 3 years ago by Joev38
  1

• Lights start blinking after a while (unsafe!)

  #126 opened 5 years ago by j0bro
  10

• Odometer is resetting every start

  #153 opened 3 years ago by deadrabbit87
  0

• tsdz2 with lcd3 problem

  #150 opened 4 years ago by Karq81
  7

• timer loop in adc.c

  #152 opened 4 years ago by 4var1
  0

• Current controller counter issue in motor.c

  #151 opened 4 years ago by 4var1
  4

• (Still) no pedaling support when light's are on.

  #139 opened 4 years ago by andrevil
  10

• Data loss on battery disconnect without turning off first

  #143 opened 4 years ago by palm369
  0

• motor.c: Wrong values for ui8_phase_x_voltage and MIDDLE_PWM_DUTY_CYCLE_MAX

  #140 opened 4 years ago by mspider65
  0

• V1.0.0 is 0.57.3 in the zip file?

  #138 opened 4 years ago by KodeZ
  0

• firmware v1.0.0 dwonload

  #137 opened 4 years ago by josch591
  2

• I'm confused about the release versions

  #130 opened 5 years ago by kaelsaes
  10

• Firmware Releases 0.57.x

  #135 opened 5 years ago by acousticsmobile
  1

• Expiremental motor type actually doesn't change the maximum RPM

  #133 opened 5 years ago by r0mko
  4

• uart communication with computer

  #132 opened 5 years ago by benno90
  2

• Wrong voltage in FW 0.20.0

  #131 opened 5 years ago by d3rsch0rsch
  1

• I broke my cadence sensor, workaround in software

  #129 opened 5 years ago by djwlindenaar
  0

• New improved communications protocol

  #125 opened 5 years ago by casainho
  7

• 0.19 performance worse than 0.18

  #112 opened 5 years ago by j0bro
  4

• new feature: mixed mode (power and torque)

  #127 opened 5 years ago by bart594
  2

• compilation on linux

  #116 opened 5 years ago by benno90
  4

• If motor stops receiving packets from display, we should do a few things for safety:

  #111 opened 5 years ago by geeksville
  3

• Control motor current instead of battery current

  #113 opened 5 years ago by AckmaniacSoftware
  5

• Flash Program Memory

  #124 opened 5 years ago by benno90
  6

• lots of "address out of range" errors when flashing lcd firmware

  #121 opened 5 years ago by glauco76
  2

• [Request] Pedal-torque threshold for 0 cadence starting.

  #107 opened 5 years ago by Frans-Willem
  12

• Official support from a Chinese manufacturer

  #110 opened 5 years ago by geeksville
  4

• Possibly two off-by-one errors in motor controller?

  #109 opened 5 years ago by Frans-Willem
  6

• Question about uninstalling firmware

  #108 opened 5 years ago by hydriniumh2
  2

• Battery SOC percentage wrongly displayed after power cycle

  #101 opened 5 years ago by j0bro
  15

• [Request] swap to off-road blinking "Assist"

  #106 opened 5 years ago by Frans-Willem
  1

• bus error while compiling LCD3/lcd.c with sdcc 3.9.0

  #104 opened 5 years ago by geeksville
  2

• ooh cool - need any help?

  #103 opened 5 years ago by geeksville
  4

• Motor assistance does not resume after standstill when lights are on

  #94 opened 5 years ago by j0bro
  5

• Error code 1 happens frequently when it should not

  #93 opened 5 years ago by casainho
  3

• Walk Assist closed loop

  #100 opened 5 years ago by leon927
  0

• Walk Assist soft start

  #99 opened 5 years ago by leon927
  0