RobTillaart/ADS1X15

Issues

• setComparatorPolarity and setComparatorLatch are inverting the setting?

  #80 opened a month ago by HineSite
  9

• COMP_POL reversed

  #76 opened 3 months ago by lynx985
  15

• possible error in the readme

  #74 opened 3 months ago by lynx985
  7

• 10-12 Channel Continuous with interrupts.

  #73 opened 5 months ago by marcus-4
  11

• wire speed

  #72 opened 6 months ago by lynx985
  22

• Differential input and gain for maximum precision.

  #71 opened 6 months ago by ChSt15
  4

• interrupt driven reads

  #70 opened 7 months ago by holgerlembke
  6

• getMaxVoltage() does not handle ADS1113

  #68 opened 7 months ago by Mark-81
  6

• [question] About using ALERT RDY in ADS_continuous_differential.ino example.

  #64 opened 10 months ago by ChipCE
  8

• Alternate I2C/TWI library or library abstraction layer

  #63 opened a year ago by commodoretim
  8

• The use of Wire1 is not allowed for ESP32 or ESP8266

  #61 opened a year ago by asantiagod
  3

• ADS1115 value from one channel is being copied to the other

  #58 opened a year ago by sghirsst
  6

• Cannot change address

  #57 opened a year ago by yihan-liu
  11

• Differential continuous mode

  #56 opened a year ago by tomelgato
  12

• Arduino Micro and ADS1115 - 860SPS (Only on 1 channel ?)

  #49 opened a year ago by MopheusDG
  62

• [Query] Example for continuously reading all four channels at max sps?

  #55 opened a year ago by subhashisbhowmik
  2

• Synchronous mode very slow

  #53 opened a year ago by git2212
  13

• Error during compiling

  #51 opened a year ago by jlcnuke
  5

• ESP32 work on Espressif 1.04 but No on Espressif 2,07

  #52 opened a year ago by ziojos
  4

• ADS1115 on RP2040 Wire, 0x4B is busy

  #45 opened 2 years ago by f5exo
  14

• How to check if the data rate is correct?

  #44 opened 2 years ago by yanxiang-wang
  8

• ADS1115 reading

  #42 opened 2 years ago
  14

• requestADC(pin); should have 0 as default,

  #40 opened 3 years ago by RobTillaart
  1

• ADS1X15::setWireClock() and high-speed mode

  #39 opened 3 years ago by MaffooClock
  11

• Suggestion: Add wrapper method to set I2C clock speed

  #22 opened 3 years ago by regcs
  23

• Not working with Nano Every

  #36 opened 3 years ago by 80stech
  11

• Library compatible for STM32F407

  #34 opened 3 years ago by hanmey97
  14

• ADS1115 Data Rate question

  #32 opened 3 years ago by sghirsst
  15

• ADS1013 broken

  #33 opened 3 years ago by JimDrewGH
  1

• QUESTION: What's the typical conversion time?

  #28 opened 3 years ago by marcdraco
  12

• ADS1X15 Continuous Mode AND differential (0_1) & (2_3)

  #29 opened 3 years ago by NovaJeff
  16

• Documentation clarification. In latch mode, alert pin goes high only after readADC?

  #26 opened 3 years ago by alicedb2
  10

• Read 4 channel asynchronous

  #24 opened 3 years ago by Mplex72
  88

• can isBusy() also verify connected() ?

  #25 opened 3 years ago by RobTillaart
  1

• Allow specifying I2C bus

  #20 opened 3 years ago by MaffooClock
  7

• ALRT Pin number?

  #19 opened 3 years ago by kritch83
  2

• ADS1115 resolution question

  #18 opened 4 years ago by thefreakyZ
  3

• 4channel continues read

  #14 opened 4 years ago by Mplex72
  20

• ADS1X15::getMaxVoltage()

  #12 opened 4 years ago by samcontrollers
  1

• Support for missing differential readings

  #9 opened 4 years ago by RobTillaart
  0

• Check documentation carefully

  #8 opened 4 years ago by RobTillaart
  0

• Add code for Comparator mode

  #1 opened 4 years ago by RobTillaart
  1

• Can this be used with esp32 dev kit? (esp-wroom32 dev board)?

  #4 opened 4 years ago by AtharZafeer
  2

• ESP32 needs a begin(sda, scl) function

  #5 opened 4 years ago by RobTillaart
  0

• ADS1013 & ADS1113 do not have gain

  #2 opened 4 years ago by RobTillaart
  0