RobTillaart/AS5600

Issues

• On AS5600_demo.ino I2C address is missing

  #72 opened 25 days ago by julien-printerbox
  2

• add update funktion for speed and cumulative position

  #67 opened a month ago by Chris-42
  14

• resetCumulativePosition not correct if direction set

  #69 opened a month ago by Chris-42
  6

• getCumulativePosition not using direction

  #65 opened a month ago by Chris-42
  16

• make wire accessing functions virtual

  #66 opened a month ago by Chris-42
  4

• rawAngle(), readAngle() only returns 0

  #64 opened 4 months ago by k4pow
  4

• getCumulativePosition messed up by http.POST

  #62 opened 7 months ago by ivukotic
  20

• Change DIR value after programming.

  #61 opened 7 months ago by vbenso
  5

• Change direction after programming.

  #60 opened 8 months ago by vbenso
  0

• Hardwired direction pin not used

  #59 opened 9 months ago by LukeSkaff
  4

• Some examples marked as AS5600 use the AS5600L

  #57 opened 9 months ago by Rob65
  6

• Failure detection on 3839 readout.

  #55 opened 9 months ago by cranefist
  9

• Teensy 4.1 cannot connect to AS5600

  #53 opened 10 months ago by SquadQuiz
  4

• Reverse rotation gives incorrect (huge) numbers.

  #50 opened 10 months ago by RobTillaart
  11

• setOffset() fails when called again

  #51 opened 10 months ago by fahadshihab
  7

• Here is the code for AS5600 library, two sensors on one bus. Maybe you can add it in the examples.

  #48 opened a year ago by laptophead
  2

• AS5600.h Library , trouble with a second sensor

  #49 opened a year ago by laptophead
  4

• Burn functions not working?

  #38 opened a year ago by cedricjeanty
  24

• Intermittent 0 degree angle returned (wrong value)

  #44 opened a year ago by antoinec4
  6

• Oscillations in speed measurements

  #43 opened a year ago by JabberwockPL
  28

• Use lib without dir pin

  #42 opened a year ago by bar2104y
  2

• Bug with using second I2C bus on ESP32 for two AS5600 encoders

  #39 opened a year ago by jtran03
  9

• Connecting multiple encoders

  #37 opened a year ago by MaksymKotwas
  7

• AS5600 module came with a resitor between PGO and GND

  #36 opened 2 years ago by Zipdox2
  3

• Weird noise in cumulative position reading

  #34 opened 2 years ago by cranefist
  6

• How to use Wire1?

  #33 opened 2 years ago by kingjamez
  10

• What is the Maximum Rotation Speed ​​in RPM?

  #32 opened 2 years ago by rtek1000
  27

• Set position when using Cumulative Position

  #30 opened 2 years ago by daniel-frenkel
  11

• i2c reading gets stuck sometimes

  #28 opened 2 years ago by hapiel
  20

• Repeatable jumps in angle value

  #24 opened 2 years ago by dead5ailor
  36

• revolution counter "edges" are incorrect

  #26 opened 2 years ago by RobTillaart
  0

• Getting range of 18-4095

  #22 opened 2 years ago by cranefist
  31

• detectMagnet always false

  #21 opened 2 years ago by DP1000
  3

• Support for other I2C addresses/AS5600L

  #19 opened 2 years ago by StathisTseflidis
  11

• investigate OUT pin

  #15 opened 2 years ago by RobTillaart
  2

• Feature request: zero-position offset

  #13 opened 2 years ago by Shdwdrgn
  17

• Add bool return to setters of config registers - check parameters

  #16 opened 2 years ago by RobTillaart
  0

• invalid mask in setConfigure

  #18 opened 2 years ago by RobTillaart
  0

• AS5600_COUNTERCLOCK_WISE fails

  #6 opened 2 years ago by Shdwdrgn
  31

• Testing

  #2 opened 2 years ago by ahmetcemturan
  7

• Handle CW and CCW in software

  #10 opened 2 years ago by RobTillaart
  0

• getAngularSpeed() fails when over 360 degrees

  #14 opened 2 years ago by RobTillaart
  2

• Optimization

  #7 opened 2 years ago by RobTillaart
  0

• Bug in setConfigure

  #8 opened 2 years ago by RobTillaart
  0

• Feature Request - get rotational speed - degrees / second.

  #4 opened 2 years ago by ahmetcemturan
  2